Uninterruptible Power Supply

Catalogs > Industrial Controls Catalog > Power Supplies > Uninterruptible Power Supply > 1609-P Industrial

1609-P Industrial

Specifications

Electrical Ratings		1609-P3000N	1609-P3000A	1609-P5000E	1609-P8000E	1609-P10000E
Input	V nom. (V AC)	120	230	208/230	208/230	208/230
	Voltage Range, default (V AC)	90…150V	160…280V
	Current (A)	20 nom., 28 max.	11 nom., 14 max.	19 nom., 24 max.	30 nom., 40 max.	39 nom., 48 max.
	Capacity	3000VA (2100 W)		5000VA (3500 W)	8000VA (6400 W)	10 000VA (8000 W)
	Frequency	45…65 Hz (self sensing)
	PFC	> 0.95
	Protection	N/A	N/A	N/A	70 A input circuit breaker
Output	V nom.	120V	208V
	Capacity	3000VA (2100 W)		5000VA (3500 W)	8000VA (6400 W)	10 000VA (8000 W)
	Protection	3…15 A circuit breaker			N/A	N/A
On Battery	Frequency	Nominal +/- 3 Hz
	Reg.	+/- 2% static +/- 5% dynamic	+/- 1% static, +/- 5% dynamic
	THD	<5% at full load
	Crest Factor	3:01
Efficiency	On Battery	86%
	On Line	88%
Protection	Surge	IEC 1000-4-4
	Overload	125% : 1 minute, 150% : 30 seconds
	Output Short	Input circuit breakers and/or premises branch protection
	Thermal Protection	Yes
	Bypass	N/A			70 A input circuit breaker
Regulatory	Safety	UL 1778, cULus, IEC 60950	EN 61000-3-2	UL 1778, cULus, IEC 60950
	EMC	FCC (Class A)	EN50091-2	FCC (Class A), EN50091-2
	Markings	cULus, CSA	CE	cULus, CSA, CE
Battery Pack	Run Time	14 minutes @ full load, 34 minutes @ half load		5…7 minutes @ full load, 13…18 minutes @ half load
	Type	Sealed Lead Acid, valve regulated, hot swappable, user replaceable
	Voltage	192V
	Charger	Temperature compensated current limited, float charger
	Recharge Time	Less than 3 hours to 90% capacity	Less than 3 hours to 85% capacity
	Lifetime	2…4 years @ 25 °C ambient
Environment	Temperature	0…40 °C (operating), -20…60 °C (short term storage)
	Altitude	10 000 ft (operating)
	Humidity	0…95% non-condensing (operating)
	Heat Output (Full Load)	655 BTU/hour		1040 BTU/hour	1536 BTU/hour	2216 BTU/hour
	Audible Noise	<50 dB @ 1 meter (full load)	<55 dB @ 1 meter (full load)
Rear Panel	AC Outlets	(6) NEMA 5…15 (2) NEMA 5…20	(8) IEC C13 (2) IEC C19		(12) IEC C13 (2) IEC C19
	AC Inlets	NEMA L5…30	IEC C14	IEC C20	3 position terminal blocks
Communication	DB9	Serial and Contact Closures
	EPO	Via Contact Closure
	Network	Via Network Management Card (1609-NMC, provided as standard with units >3 KVA)
Indicators and Controls	LED Status	On-line, In Bypass Mode, On Battery, Overload and Replace Battery, Fault, Bar graph for Load, Bar graph for Battery Fuel Gauge, Bar graph for Measured Input Voltage when recessed switch is held
	Control	(Front panel) On/self-test/alarm silence/cold start/load off
	Audible	On Battery: 4 short beeps repeats about 20 seconds (mutable), Low Battery: persistent 0.5 second beep every 1 second (mutable), In Bypass: continuous beeping, Failure: continuous tone, Replace Battery: occasional on/off change - single beep

	Wiring of the UPS should be performed by a qualified electrician. Use appropriate size wires.
	In 230V AC applications, the UPS must be protected with a circuit breaker that complies with European standards for branch rated protection per the country of installation.
	In 208V AC applications, the UPS must be protected by a dual-pole, 10 A branch rated, UL 489 circuit breaker.
	The 120V AC 1609-P3000N has supplementary circuit breaker protection. The unit should be protected by a single-pole, 15 A branch rated, UL 489 circuit breaker. Allen-Bradley part number 1492-MCAA115 is suggested.
	The branch circuit breaker must be off prior to wiring the unit.

Notes

208V AC applications: The 1609-P5000E, 1609-P8000E, and 1609-P10000E, ship ready for 230V AC sources. When operating one of these in 208V AC applications, the UPS low transfer voltage settings are adjusted through the PowerChute^® software or the Network Management Card.

Refer to the PowerChute^® User Guide or the Network Management Card instructions for details.