Catalogs > Industrial Controls Catalog > Power Supplies > Uninterruptible Power Supply > 1609-S Industrial

1609-S Industrial

Introduction

Standards Compliance and Certifications

Catalog Number Explanation

Product Selection

Accessories

Specifications

Approximate Dimensions and Shipping Weights

Specifications

		1609-S350NS	1609-S350ES
Input	Wiring	Touch-proof terminal block
	Nominal Voltage	120V	208/230V
	Voltage Range, Default	81…143V	160…287V
	Voltage Range, Widest, On Line	75…153V	150…300V
	Nominal Current	2.9 A	1.5 A
	Capacity	350VA/280 W
	Frequency	47…63 Hz
	PFC	None, load power factor is reflected in the input line current
On Line Output	Wiring	Touch-proof terminal block
	Nominal Voltage	120V	208/230V
	Voltage Range, Default	106…127V	208…253V
	Voltage Range, Widest, On Line	97…136V	196…265V
	Transfer Point Accuracy	+/- (2% of transfer voltage + 1.3)	+/- (2% of transfer voltage + 2.6)
	Overload Protection	Alarm at 107% of rated load input circuit breaker	Alarm at 107% of rated load Premises branch protection 10 A or less
	Efficiency	96% @ 100% resistive load
	Surge Protection	Per EN50091-2
On Battery Output	Frequency	Nominal +/- 3 Hz (Locked), Nominal +/- 0.5 Hz (Free-running)
	THD	< 5% at full (linear) load
	Voltage Regulation	+/- 5%, + 5…-15% after low battery warning
	Crest Factor	2.5:1
	Efficiency	77% @ 100% resistive load
	Overload Protection	Overload indication and shutdown @ 107% of rate load or electronic current limit and shutdown under short circuit condition
Battery Pack	Run Time	12 minutes (full load) 24 minutes (50% full load)
	Type	Sealed lead acid, valve-regulated hot-swappable, user-replaceable
	Voltage	24V
	Charger	Temperature-compensated, current-limited, float charger
	Recharge Time	Less than 3 hours to 90% capacity
	Lifetime	3…5 years @ 25 °C ambient Lifetime cut in half for every 10 °C above 25 °C
Environment	Temperature	0…40 °C (operating), -15…45 °C (short-term storage)
	Altitude	10 000 ft (operating)
	Humidity	0…95% non-condensing (operating)
	Heat Output	On line, full load: 137 BTU per hour On line, full load, charging: 190 BTU per hour On battery, full load: 1706 BTU per hour
	Audible Noise	<45 dB @ 1 m (full load)
Communication	Serial	Serial RS232 DB-9
	Options	Dry contact I/O communication cable
Indicators and Controls	Status LEDs	On line (green) AVR low line (yellow) AVR high line (yellow) On battery (yellow) Overload and fault (red) Bad battery (red) Load percentage of full rating bar graph (green) Battery state of charge bar graph (green) Measured input voltage indicated by load bar graph when recessed switch is held
	Control Buttons	On/self-test/alarm silence/cold start Output off
	Audible Alarms	On Battery: 4 short beeps repeats about 20 seconds (mute capability) Low Battery: persistent 0.5 second beep every 1 second (mute capability) Disconnected Battery: continual chirping Failure: continuous tone Replace Battery: occasional On/off change: single beep

	Wiring of the UPS should be performed by a qualified electrician. Use appropriate size wires.
	In 230V AC applications, the UPS must be protected with a circuit breaker that complies with European standards for branch rated protection per the country of installation.
	In 208V AC applications, the UPS must be protected by a dual-pole, 10 A branch rated, UL 489 circuit breaker.
	The 120V AC 1609-S350NS has supplementary circuit breaker protection. The unit should be protected by a single-pole, 15 A branch rated, UL 489 circuit breaker. Allen-Bradley part number 1492-MCAA115 is suggested.
	The branch circuit breaker must be off prior to wiring the unit.