22 mm

Catalogs > Industrial Controls Catalog > Push Buttons > 22 mm > Bulletin 800MR/800MB Push Buttons

Bulletin 800MR/800MB Push Buttons

Modifications and Accessories

Contact Blocks

Bulletin 800M contact blocks are available with quick connect type terminals and screw terminals with pressure plates (in two sizes). Each quick connect type termination will accept two 0.110 x 0.032 in. push-on connectors or one 0.250 x 0.032 in. connector. Each small screw terminal with pressure plate will accept a maximum of one #14 AWG wire or two #16 AWG wires. The large screw terminals with pressure plates are similar in size to the Bulletin 800T (full size) contact block terminals.

Cat. No. 800M-XA		Cat. No. 800M-XAS		Cat. No. 800M-XAK		Cat. No. 800M-XAR

Contact Arrangement	Standard Block			Logic Reed Block‡
	Quick Connect Terminals	Small Screw Terminals with Pressure Plates	Large Screw Terminals with Pressure Plates	Quick Connect Terminals
	Cat. No.	Cat. No.	Cat. No.	Cat. No.
1 N.O.	800M-XD1	800M-XD1S	800M-XD1K	800M-XD1R
1 N.C.	800M-XD2	800M-XD2S	800M-XD2K	800M-XD2R
1 N.O. - 1 N.C.	800M-XA	800M-XAS	800M-XAK	800M-XAR
2 N.O.	800M-XA2	800M-XA2S	800M-XA2K	800M-XA2R
2 N.C.	800M-XA4	800M-XA4S	800M-XA4K	800M-XA4R
1 N.O.E.M. - 1 N.C.L.B.	800M-XA3	800M-XA3S	800M-XA3K	—
1 N.C.L.B. - 1 N.C.	800M-XA7	800M-XA7S	800M-XA7K	—
‡ Screw terminals with pressure plates are not available.

Note:For contact block rating information see Standard Contact Ratings.

Color Caps

Non-Illuminated Devices

Flush Head Push Buttons		Extended Head Push Buttons		Mushroom Buttons		Push-Pull Units		Twist or Pull Release Caps

Color	Flush Head Push Buttons	Extended Head Push Buttons	Mushroom Buttons	Push-Pull Units	Twist or Pull Release Caps
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Green	800MR-N41	800MR-N21	800MR-N56G	800MR-N160B	800MR-N30B
Black	800MR-N42	800MR-N22	800MR-N56B	800MR-N160H	800MR-N30H
Orange	800MR-N43	800MR-N23	800MR-N56O	800MR-N160F	800MR-N30F
Gray	800MR-N44	800MR-N24	800MR-N56GR	800MR-N160G	—
White	800MR-N45	800MR-N25	800MR-N56W	800MR-N160J	—
Red	800MR-N46	800MR-N26	800MR-N56R	800MR-N160A	800MR-N30A
Blue	800MR-N47	800MR-N27	800MR-N56BL	800MR-N160C	800MR-N30C
Yellow	800MR-N49	800MR-N29	800MR-N56Y	800MR-N160E	800MR-N30E

Illuminated Devices

Pilot Light		Push-to-Test Pilot Light and Illuminated Push Button		Push-Pull Unit		Mushroom Button		Twist or Pull Release Caps

Color	Pilot Lights	Push-to-Test Pilots and Illuminated Push Buttons	Illuminated Push-Pull Units	Illuminated Mushroom Buttons	Illuminated Twist or Pull Release Caps
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Red	800MR-N1R	800MR-N2R	800MR-N159R	800MR-N156R	800MR-N20R
Green	800MR-N1G	800MR-N2G	800MR-N159G	—	800MR-N20G
Amber	800MR-N1A	800MR-N2A	800MR-N159A	800MR-N156A	800MR-N20A
Blue	800MR-N1B	800MR-N2B	800MR-N159B	800MR-N156B	800MR-N20B
White	800MR-N1W	800MR-N2W	800MR-N159W	800MR-N156W	—
Clear	800MR-N1C	800MR-N2C	800MR-N159C	800MR-N156C	800MR-N20C

Replacement Selector Switch Knobs

Selector Knob Cat. No. 800MR-NG		Selector Knob Lever Cat. No. 800MR-NK		Selector Knob Cat. No. 800MR-LB		Selector Knob Lever Cat. No. 800MR-LM

Knobs

Color	Selector Switch Knobs, Non-Illuminated		Color	Selector Switch Knobs, Illuminated
	Standard Knob	Knob Lever		Standard Knob	Knob Lever
	Cat. No.	Cat. No.		Cat. No.	Cat. No.
Gray	800M-NG	800M-NT		—	—
Red	800M-NA	800M-NL		—	—
Green	800M-NB	800M-NM	Red	800M-LA	800M-LL
Blue	800M-NC	800M-NN	Amber	800M-LD	800M-LP
Yellow	800M-NE	800M-NR	Clear	800M-LY	800M-LZ
Orange	800M-NF	800M-NS	Green	800M-LB	800M-LM
Black	800M-NH	800M-NK		—	—
White	800M-NJ	800M-NV		—	—

Bul. 800MB Color Chip Kits

	Description	Type of Unit	Color	Cat. No.
	Color Chip Kits These kits are available for replacement on backlit style devices. A packet of color chips containing one of each color is included in each kit.	Full-face illuminated	Amber	800MS-N10A
			Blue	800MS-N10B
			Clear	800MS-N10C
			Green	800MS-N10G
			Red	800MS-N10R
		Non-illuminated	Blue	800MS-N12B
			Grey	800MS-N12GR
			Green	800MS-N12G
			Orange	800MS-N12O
			Red	800MS-N12R
			White	800MS-N12W
			Yellow	800MS-N12Y
Cat. No. 800MS‑N10

General Accessories

Boots

	Description		Cat. No.
	Insulation Boot When properly combined with a Bulletin 800MR unit, this device meets CSA grounding requirements.		800M-N18
	Description	Color	Cat. No.
	Rubber Boot These accessories are used as dust covers. They can be added to flush and extended head push button units (illuminated and non-illuminated) to protect against foreign materials from reaching the opening between the button and the mounting ring.	Black	800MR-N8
		Red	800MR-N9
		Green	800MR-N10
		Blue	800MR-N11
		Yellow	800MR-N12
Cat. No. 800MR‑N9		Clear	800MR-N14

Miscellaneous

	Description	Cat. No.
	Extended Mounting Ring This mounting ring protects against accidental push button operation.	800MR-N4
	Padlocking Cover Stainless steel mounting bracket with clear plastic cover. Guards against unauthorized operation. Used with round design push buttons and selector switches (not for use with wing lever). Also available for 2-position push-pull units (button must be in the depressed position when the cover is closed).	800MR-N6
(Padlock not included)

Miscellaneous, Continued

	Description	Cat. No.
	Locking Ring Wrench This device is used to tighten and loosen mounting rings properly in the 800MR family.	800MR-N3
	Hole Closing Plug Wherever an enclosure or flush plate with more than the required number of openings is used, this neat-appearing plug can be supplied to close the unused openings.	800M-N1
	Lamp Remover This tool can be used to remove and install wedge based lamps in Illuminated selector switches.	800M-N5
	Connectors Used with wire sizes AWG 18…22. The connectors come in packages of 100 pieces.	⋆	800M-NT2
	Guard for Illuminated Push Buttons This device is used to prevent accidental operation of illuminated push buttons.	800MR-N93
	Mounting Ring This device is a retaining ring used to keep an operator in the panel when removing the guard ring to service the light bulb.	40167-287-02
	Lens Remover This device makes it easier to remove the lens.	800MS-N9
⋆ These must be ordered in multiples of 100.

Miscellaneous, Continued

	Description	Style	Color	Cat. No.
	Additional Bezels These bezels fit square traditional and backlit styles.		Grey	800MS-N16
Cat. No. 800MS-N16 (Grey) Cat. No. 800MB-N16 (Black)			Black	800MB-N16
		Flush button backlit	Grey	800MS-N17
			Black	800MB-N17
		Extended button backlit	Grey	800MS-N18
			Black	800MB-N18
Cat. No. 800MS‑N17
	Description	Type		Cat. No.
	Legend Insert Do-It-Yourself Kits These kits contain material necessary to create transparent backlit legend inserts	Legend marking start package		800MS-N13

Replacement Lamps

Replacement Incandescent and Light Emitting Diode (LED) Lamps

Lamp	Type	Lamp Voltage	ANSI Number	Cat. No.
Incandescent	Full Voltage and Transformer	6.3V AC	86	800M-N15
	Full Voltage	12V AC/DC	73	800M-N16
		24V AC/DC	85	800M-N17
	Dual Input Transformer	6.3V AC	755/1866	800T-N65
Standard LED	Full Voltage	6.3V AC/DC	—	⋆	800T-N60x
		14V AC/DC	—	⋆	800T-N61x
		28V AC/DC	—	‡	800T-N62x
		120V AC	—	⋆	800T-N64x
	Full Voltage	6.3V AC/DC	—	⋆	800T-N60x
⋆ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, White, or Blue.
‡ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, or White.

All illuminated devices, except dual input transformer units, use T 1-3/4 wedge base units. Existing Bulletin 800M devices may have incandescent lamps replaced with shock and vibration resistant LEDs. Existing ANSI# 86, 73, or 85 lamps may be replaced by LEDs.

Bul. 800MR Legend Plates

Standard Size Blank Legend Plate Gray (Cat. No. 800MR-W00) Red (Cat. No. 800MR-W600)		Large Size Blank Legend Plate Gray (Cat. No. 800MR-W100) Red (Cat. No. 800MR-W6100)

Push Buttons/Pilot Lights
Marking	Cat. No.	Marking	Cat. No.	Marking	Cat. No.
CLOSE	800MR-W01	LOWER	800MR-W11	SLOW	800MR-W18
DOWN	800MR-W02	OFF	800MR-W09	START	800MR-W19
EMERG. STOP (Red)	800MR-W624	ON	800MR-W10	STOP (Red)	800MR-W620
FAST	800MR-W03	OPEN	800MR-W13	TEST	800MR-W21
FORWARD	800MR-W23	OUT	800MR-W12	UP	800MR-W22
HIGH	800MR-W04	PUSH-TO-TEST	800MR-W29	1ST SPEED	800MR-W25
IN	800MR-W06	RAISE	800MR-W14	2ND SPEED	800MR-W26
INCH	800MR-W07	RESET	800MR-W15	3RD SPEED	800MR-W27
JOG	800MR-W08	REV	800MR-W16	4TH SPEED	800MR-W28
LOW	800MR-W05	RUN	800MR-W17	—	—

Selector Switches
Marking	Cat. No.	Marking	Cat. No.	Marking	Cat. No.
OPEN-CLOSE	800MR-W57	STOP-START	800MR-W64	HAND-OFF-AUTO	800MR-W78
RAISE-LOWER	800MR-W58	SUM-WINT	800MR-W65	HIGH-LOW	800MR-W53
RUN-JOG	800MR-W59	UP-DOWN	800MR-W66	JOG-REV	800MR-W54
SAFE-RUN	800MR-W60	1-2-3-4	800MR-W80	JOG-RUN	800MR-W55
SLOW-FAST	800MR-W61	AUTO-OFF-HAND	800MR-W79	JOG-STOP-RUN	800MR-W76
SLOW-OFF-START	800MR-W75	FOR-OFF-REV	800MR-W77	LEFT-RIGHT	800MR-W56
START-JOG	800MR-W62	FOR-REV	800MR-W51	OFF-ON	800MR-W50
START-STOP	800MR-W63	HAND-AUTO	800MR-W52	—	—

Blank Legends		Custom Legends
Size — Color	Cat. No.	Number of Lines and Characters	Cat. No.
Standard — Gray	800MR-W00	1 Line, 12 Characters	800MR-W00E plus Custom Text
Large — Gray	800MR-W100	2 Lines, 12 Characters	800MR-W100E plus Custom Text
Standard — Red	800MR-W600	1 Line, 12 Characters	800MR-W600E plus Custom Text
Large — Red	800MR-W6100	2 Lines, 12 Characters	800MR-W6100E plus Custom Text

Extra Large Legend Plates

An adapter ring is available for Bulletin 800MR push buttons when used with Bulletin 800T legend plates. Order Cat. No. 800MR-N50. Refer to Approximate Dimensions and Shipping Weights for dimension requirements.

Cat. No. 800MR-W645		Cat. No. 800MR-W646		Cat. No. 800MR-W647		Cat. No. 800MR-W130		Cat. No. 800MR-N50

Format	Cat. No.	Format	Cat. No.
Large Size with Adapter Ring (Blank)	800MR-W645	For Push-Pull only Push Stop Pull Start	800MR-W130
Round with Adapter Ring (Blank)	800MR-W646	Adapter Ring⋆  Used with Bulletin 800T Legend Plates	800MR-N50
Pre-printed includes Adapter Ring (Cat. No. 800MR-N50) Push to Stop Twist or Pull Release	800MR-W647	—	—
⋆ To use the Bulletin 800T legend plates with Bulletin 800MR devices, use adapter ring (Cat. No. 800MR-N50).

Bul. 800MB Special Legend Inserts

Special legend inserts are available. To order, specify Cat. No. 800MS-WC00E and marking required. A maximum of nine characters per line: one or two lines 0.140 in. high characters; three or four lines 0.110 in. high characters.

Bul. 800MB Backlit Legends

The table lists standard legend markings that are available. To order legend insert only, add the suffix of the legend to Cat. No. 800MS-WC. Example: Cat. No. 800MS-WC03 would be a FAST legend insert only.

Marking	Suffix	Marking	Suffix	Marking	Suffix	Marking	Suffix
CLOSE	01	LOW	05	RESET	15	UP	22
DOWN	02	LOWER	11	REV	16	1ST SPEED	25
FAST	03	OFF	09	RUN	17	2ND SPEED	26
FORWARD	23	ON	10	SLOW	18	3RD SPEED	27
HIGH	04	OPEN	13	START	19	4TH SPEED	28
IN	06	OUT	12	STOP	20	0	40
INCH	07	PUSH-TO-TEST	29	EMERG STOP	24	1	41
JOG	08	RAISE	14	TEST	21	—	—