Bulletin 800MB Push Buttons

Bulletin 800MB

• 22.5 mm mounting hole
  
• Type 13 oiltight
  
• Square backlit operators
  

Standards Compliance and Certifications

UL Listed — File: E14840
Guide: NKCR
CSA Certified (File No. LR1234)

Product Selection

Momentary Contact Push Button Units, Non-Illuminated

Contact Terminations

Devices come standard with stab terminations. For large screw contact terminations, add letter K to the end of the cat. no. For small screw terminations, add the letter S.

Flush Head Unit Cat. No. 800MB-CA1B		Extended Head Unit Cat. No. 800MB-CB1B

Contact Type		Button Color	Flush Head	Extended Head
			Cat. No.	Cat. No.
	1 N.O.	Green	800MB-CA1D1	—
		Gray	800MB-CA4D1	800MB-CB4D1
		Red	—	800MB-CB6D1
		Yellow	800MB-CA9D1	800MB-CB9D1
	1 N.C.	Green	800MB-CA1D2	—
		Gray	800MB-CA4D2	800MB-CB4D2
		Red	—	800MB-CB6D2
		Yellow	800MB-CA9D2	800MB-CB9D2
	1 N.O. - 1 N.C.	Green	800MB-CA1A	—
		Gray	800MB-CA4A	800MB-CB4A
		Red	—	800MB-CB6A
		Yellow	800MB-CA9A	800MB-CB9A
	2 N.O. - 2 N.C.	Green	800MB-CA1B	—
		Gray	800MB-CA4B	800MB-CB4B
		Red	—	800MB-CB6B
		Yellow	800MB-CA9B	800MB-CB9B

Push Buttons, Illuminated

Momentary Contact Push Button Units, Illuminated

Contact Terminations

Devices come standard with stab terminations. For large screw contact terminations, add letter K to the end of the cat. no. For small screw terminations, add the letter S.

Flush Head Unit Cat. No. 800MB-CPA16GA		Extended Head Unit Cat. No. 800MB-CQB24RA

Contact Type	Type	Volts/Lamp	Color	Flush Head	Extended Head
				Cat. No.	Cat. No.
	Full voltage	24 AC/DC Incandescent 50/60 Hz	Red	—	800MB-CQB24RA
			Green	800MB-CQA24GA	—
			Amber	800MB-CQA24AA	800MB-CQB24AA
	Transformer	120 AC Incandescent	Red	—	800MB-CPB16RA
			Green	800MB-CPA16GA	—
			Amber	800MB-CPA16AA	800MB-CPB16AA
	Full voltage	12 AC/DC LED	Red	—	800MB-CQBL12RA
			Green	800MB-CQAL12GA	—
1 N.O. - 1 N.C.			Amber	800MB-CQAL12AA	800MB-CQBL12AA
		24 AC/DC LED	Red	—	800MB-CQBL24RA
			Green	800MB-CQAL24GA	—
			Amber	800MB-CQAL24AA	800MB-CQBL24AA
	Transformer	120 AC LED 50/60 Hz	Red	—	800MB-CPBL16RA
			Green	800MB-CPAL16GA	—
			Amber	800MB-CPAL16AA	800MB-CPBL16AA

Momentary Contact Push Button Units, Non-Illuminated

800	MB	–	CA		1		A
	a		b		c		d		e

a

b

c

d

d (cont’d)

e

Bezel Color

Operator Type

Color Insert

Contact Block(s)

Contact Block(s)

Contact Block Termination Type

Standard

Logic Reed with Stab Terminals

Code

Color

Code

Description

Code

Color

Code

Description

Code

Description

Code

Description

MB

Black

CA

Flush head

X

No color insert

Blank

No contacts

D1R

1 N.O.

Blank

Stab terminals

MS

Gray

CB

Extended head

1

Green

D1

1 N.O.

D2R

1 N.C.

K

Large screwT

3

Orange

D2

1 N.C.

AR

1 N.O. - 1 N.C.

S

Small screwT

4

Gray

A

1 N.O. - 1 N.C.

A2R

2 N.O.

5

White

A2

2 N.O.

A4R

2 N.C.

6

Red¬

A4

2 N.C.

BR

2 N.O. - 2 N.C.

7

Blue

A7

1 N.C.L.B. - 1 N.C.

9

Yellow

B

2 N.O. - 2 N.C.

Momentary Contact Push Button Units, Illuminated

800

MB

–

CQ

A

L

06

R

A

a

b

c

d

e

f

g

h

a

b

c

d

e

Bezel Color

Power Module Type

Operator Type

Illumination Options

Voltage

Full Voltage

Code

Color

Code

Description

Code

Description

Code

Description

Code

Description

MB

Black

CQ

Full Voltage

A

Flush

Blank

Incandescent

06

6V AC/DC

MS

Gray

CP

Transformer

B

Extended

L

LED‡ §

12

12V AC/DC

24

24V AC/DC

10

120V AC§

Transformer

Code

Description

16

120V AC

26

240V AC

f			g			g (cont’d)			h
Color Insert			Contact Block(s)			Contact Block(s)			Contact Block Termination Type
			Standard			Logic Reed with Stab Terminals
Code	Color		Code	Description		Code	Description		Code	Description
Blank	No contacts		Blank	No contacts		D1R	1 N.O.		Blank	Stab terminals
X	Packet of colored insertsØ		D1	1 N.O.		D2R	1 N.C.		K	Large screwT
A	Amber		D2	1 N.C.		AR	1 N.O. - 1 N.C.		S	Small screwT
B	Blue		A	1 N.O. - 1 N.C.		A2R	2 N.O.
C	Clear		A2	2 N.O.		A4R	2 N.C.
G	Green		A4	2 N.C.		BR	2 N.O. - 2 N.C.z
R	Red¬		A7	1 N.C.L.B. - 1 N.C.
			B	2 N.O. - 2 N.C.z

¬ Red flush head push buttons are not suitable for applications requiring extended head or other unguarded buttons capable of being operated quickly in emergencies, and they may not comply with applicable codes or standards.
T Not available with Logic Reed contact blocks.
‡ LEDs are only available in red, green, amber, and white; lens color must match LED color.
§ White LED available in 24V AC/DC only.
§ LED only.
Ø Packet of colored inserts, one of each color. Not available with LED option for illuminated devices.
z Only available with full voltage illumination option and standard stab terminations.

Dual Lamp Momentary Contact Push Button Units, Illuminated

Contact Terminations

Devices come standard with stab terminations. Screw terminations are not available for these operators.

Flush Head Unit Cat. No. 800MB-DA24GRBK		Extended Head Unit Cat. No. 800MB-DG12RGA

Type	Contact	Lamp	Volts	Color	Flush Head	Extended Head
					Cat. No.	Cat. No.
Full voltage		Incandescent	12 AC/DC	Red (top) Green (bottom)	800MB-DA12RGA	800MB-DG12RGA
			24 AC/DC		800MB-DA24RGA	800MB-DG24RGA
			12 AC/DC	Blank with pack of color inserts	800MB-DA12XXA	800MB-DG12XXA
			24 AC/DC		800MB-DA24XXA	800MB-DG24XXA
		LED	12 AC/DC	Red (top) Green (bottom)	800MB-DAL12RGA	800MB-DGL12RGA
			24 AC/DC		800MB-DAL24RGA	800MB-DGL24RGA
	1 N.O. - 1 N.C.
		Incandescent	12 AC/DC	Red (top) Green (bottom)	800MB-DA12RGB	800MB-DG12RGB
			24 AC/DC		800MB-DA24RGB	800MB-DG24RGB
			12 AC/DC	Blank with pack of color inserts	800MB-DA12XXB	800MB-DG12XXB
			24 AC/DC		800MB-DA24XXB	800MB-DG24XXB
		LED	12 AC/DC	Red (top) Green (bottom)	800MB-DAL12RGB	800MB-DGL12RGB
			24 AC/DC		800MB-DAL24RGB	800MB-DGL24RGB
	2 N.O. - 2 N.C.

800

MB

–

DA

L

24

G

R

A

a

b

c

d

e

f

g

a			b			c			d
Bezel Color			Operator Type			Illumination Options			Power Module Type and Voltage‡
									Full Voltage
Code	Color		Code	Description		Code	Description		Code	Description
MB	Black		DA	Flush head		Blank	Incandescent		06	6V AC/DC
MS	Gray		DG	Extended head		L	LED¬ T		12	12V AC/DC
									24	24V AC/DC
									10	120V AC§

e			f			g
Lens Color			Lens Color			Contact Block(s)
Top Position			Bottom Position			Standard
Code	Color		Code	Color		Code	Description
X	Packet of colored inserts§		X	Packet of colored inserts§		Blank	No contacts
A	Amber		A	Amber		D1	1 N.O.
B	Blue		B	Blue		D2	1 N.C.
C	Clear/white		C	Clear/white		A	1 N.O. - 1 N.C.
G	Green		G	Green		A2	2 N.O.
R	Red		R	Red		A4	2 N.C.
						A7	1 N.C.L.B. - 1 N.C.
						B	2 N.O. - 2 N.C.
						Logic Reed with Stab Terminals
						D1R	1 N.O.
						D2R	1 N.C.
						AR	1 N.O. - 1 N.C.
						A2R	2 N.O.
						A4R	2 N.C.
						BR	2 N.O. - 2 N.C.

¬ LEDs are only available in red, green, amber, and white; lens color must match LED color.
T White LED available in 24V AC/DC only.
‡ Both lamps must be the same voltage.
§ LED only.
§ Packet of colored inserts, one of each color. Not available with LED illumination option.

Pilot Light Units

Contact Terminations

Devices come standard with stab terminations. For large screw contact terminations, add letter S to the end of the cat. no. For push-to-test pilot lights, add the letter K.

Pilot Light Cat. No. 800MB-CQ24RS		Push-to-Test Pilot Light Cat. No. 800MB-CPT16G

Lamp	Type	Volts	Color	Pilot Light	Push-to-Test
				Cat. No.	Cat. No.
Incandescent	Full voltage	24 AC/DC	Red	800MB-CQ24R	800MB-CQT24R
			Green	800MB-CQ24G	800MB-CQT24G
			Amber	800MB-CQ24A	800MB-CQT24A
	Transformer	120 AC 50/60 Hz	Red	800MB-CP16R	800MB-CPT16R
			Green	800MB-CP16G	800MB-CPT16G
			Amber	800MB-CP16A	800MB-CPT16A
LED	Full voltage	12 AC/DC	Red	800MB-CQL12R	800MB-CQTL12R
			Green	800MB-CQL12G	800MB-CQTL12G
			Amber	800MB-CQL12A	800MB-CQTL12A
		24 AC/DC	Red	800MB-CQL24R	800MB-CQTL24R
			Green	800MB-CQL24G	800MB-CQTL24G
			Amber	800MB-CQL24A	800MB-CQTL24A
	Transformer	120 AC 50/60 Hz	Red	800MB-CPL16R	800MB-CPTL16R
			Green	800MB-CPL16G	800MB-CPTL16G
			Amber	800MB-CPL16A	800MB-CPTL16A

Pilot Light Units, Dual Lamp

Contact Terminations

Devices come standard with stab terminations. Screw terminations are not available for these operators.

Pilot Light Cat. No. 800MB-DL24GR		Push-to-Test Pilot Light Cat. No. 800MB-DT24RG

Type	Lamp	Volts	Color	Pilot Light	Push-to-Test
				Cat. No.	Cat. No.
Full voltage	Incandescent	12 AC/DC	Red (top) Green (bottom)	800MB-DL12RG	800MB-DT12RG
		24 AC/DC		800MB-DL24RG	800MB-DT24RG
		12 AC/DC	Blank with pack of color inserts	800MB-DL12XX	800MB-DT12XX
		24 AC/DC		800MB-DL24XX	800MB-DT24XX
	LED	12 AC/DC	Red (top) Green (bottom)	800MB-DLL12RG	800MB-DTL12RG
		24 AC/DC		800MB-DLL24RG	800MB-DTL24RG

Pilot Light Units

800	MB	–	CP		L		24		R
	a		b		c		d		e		f

a			b			c
Bezel Color			Power Module Type			Illumination Options
Code	Color		Code	Description		Code	Description
MB	Black		CP	Transformer		Blank	Incandescent
MS	Gray		CQ	Full voltage		L	LED¬ T
						T	Push-to-test
						TL	Push-to-test with LED¬ T

d			e			f
Voltage			Lens Color			Termination Type
Full Voltage						Pilot Lights
Code	Description		Code	Color		Code	Description
06	6V AC/DC		X	Packet of colored inserts§		Blank	Stab terminals
12	12V AC/DC		A	Amber		S	Large screw
24	24V AC/DC		B	Blue		Push-to-Test Pilot Lights
10	120V AC‡		C	Clear/white		Code	Description
Transformer			G	Green		Blank	Stab terminals
Code	Description		R	Red		K	Large screw§
16	120V AC					S	Small screw§
26	240V AC

Pilot Light Units, Dual Lamp

800

MB

–

DL

L

06

G

R

a

b

c

d

e

f

g

a			b			c			d
Bezel Color			Operator Type			Illumination Options			Power Module Type and VoltageØ
									Full Voltage
Code	Color		Code	Description		Code	Description		Code	Description
MB	Black		DL	Pilot light		Blank	Incandescent		06	6V AC/DC
MS	Gray		DT	Push-to-test		L	LED ¬ T		12	12V AC/DC
									24	24V AC/DC
									10	120V AC ‡

e			f			g
Lens Color			Lens Color			Termination Type
Top Position			Bottom Position
Code	Color		Code	Color		Code	Description
X	Packet of colored inserts §		X	Packet of colored inserts §		Blank	Stab terminals
A	Amber		A	Amber
B	Blue		B	Blue
C	Clear/White		C	Clear/White
G	Green		G	Green
R	Red		R	Red

¬ LEDs are only available in red, green, amber, and white; lens color must match LED color.
T White LED available in 24V AC/DC only.
‡ LED only.
§ Packet of colored inserts, one of each color. Not available with LED illumination option.
§ Only available with full voltage power module and standard stab terminations.
Ø Both lamps must be the same voltage.

Accessories

Modifications and Accessories

Boots

	Description	Cat. No.
	Insulation Boot When properly combined with a Bulletin 800MR unit, this device meets CSA grounding requirements.	800M-N18
Cat. No. 800M-N18

Miscellaneous

	Description		Cat. No.
	Lamp Remover This tool can be used to remove and install wedge based lamps in Illuminated selector switches.		800M-N5
Cat. No. 800M‑N5
	Connectors Used with wire sizes AWG 18…22. The connectors come in packages of 100 pieces.		¬	800M-NT2
Cat. No. 800M‑NT2
	Lens Remover This device makes it easier to remove the lens.		800MS-N9
Cat. No. 800MS‑N9
	Description	Style	Color	Cat. No.
	Additional Bezels These bezels fit square traditional and backlit styles.	Flush button backlit	Grey	800MS-N17
			Black	800MB-N17
		Extended button backlit	Grey	800MS-N18
			Black	800MB-N18
Cat. No. 800MS‑N17
	Description	Type		Cat. No.
	Legend Insert Do-It-Yourself Kits These kits contain material necessary to create transparent backlit legend inserts	Legend marking start package		800MS-N13
		Legend marking start package - French		800MS-N13F
		Legend marking blank grid, bond paper		800MS-N14
		Legend marking blank grid, vellum paper		800MS-N15
Cat. No. 800MS‑N13
¬ These must be ordered in multiples of 100.

Modifications and Accessories, Continued

	Description	Type of Unit	Color	Cat. No.
	Color Chip Kits These kits are available for replacement on backlit style devices. A packet of color chips containing one of each color is included in each kit.	Full-face illuminated	Amber	800MS-N10A
			Blue	800MS-N10B
			Clear	800MS-N10C
			Green	800MS-N10G
			Red	800MS-N10R
		Split-lens illuminated	Amber	800MS-N11A
			Blue	800MS-N11B
			Clear	800MS-N11C
			Green	800MS-N11G
			Red	800MS-N11R
		Non-illuminated	Blue	800MS-N12B
			Grey	800MS-N12GR
			Green	800MS-N12G
			Orange	800MS-N12O
			Red	800MS-N12R
			White	800MS-N12W
			Yellow	800MS-N12Y
Cat. No. 800MS‑N10

Legend Plates

Special Legend Inserts

Special legend inserts are available. To order, specify Cat. No. 800MS-WC00E and marking required. A maximum of nine characters per line: one or two lines 0.140 in. high characters; three or four lines 0.110 in. high characters.

Split Face Legend Inserts

When ordering dual lamp legend inserts, specify Cat. No. 800MS-WC88E and marking required. A maximum of nine characters per line: one or two lines 0.140 in. characters; three or four lines 0.110 in. characters.

Bulletin 800M Backlit Legends

The table lists standard legend markings that are available. To order legend insert only, add the suffix of the legend to Cat. No. 800MS-WC. Example: Cat. No. 800MS-WC03 would be a FAST legend insert only. To order a standard legend insert with the backlit style device, add the suffix from the table to the end of the cat. no. Example: Cat. No. 800MS-CP16R09.

Marking	Suffix	Marking	Suffix	Marking	Suffix	Marking	Suffix
CLOSE	01	LOW	05	RESET	15	UP	22
DOWN	02	LOWER	11	REV	16	1ST SPEED	25
FAST	03	OFF	09	RUN	17	2ND SPEED	26
FORWARD	23	ON	10	SLOW	18	3RD SPEED	27
HIGH	04	OPEN	13	START	19	4TH SPEED	28
IN	06	OUT	12	STOP	20	0	40
INCH	07	PUSH-TO-TEST	29	EMERG STOP	24	1	41
JOG	08	RAISE	14	TEST	21	—	—

Replacement and Light Emitting Diode (LED) Lamps

Lamp	Type	Lamp Voltage	ANSI Number	Cat. No.
	Full Voltage and Transformer	6.3V AC	86	800M-N15
	Full Voltage	12V AC/DC	73	800M-N16
Incandescent		24V AC/DC	85	800M-N17
	Full Voltage	6.3V AC/DC	—	¬	800T-N60x
		14V AC/DC	—	¬	800T-N61x
		28V AC/DC	—	T	800T-N62x
		120V AC	—	¬	800T-N64x
Standard LED	Transformer	6.3 AC	—	¬	800T-N60x
¬ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, or Red.
T To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, or White.

All illuminated devices, except dual input diode and dual input transformer units, use T 1-3/4 wedge base units. Existing Bulletin 800M devices may have incandescent lamps replaced with shock and vibration resistant LEDs. Existing ANSI# 86, 73, or 85 lamps may be replaced by LEDs.

Specifications

Specifications¬ 

Electrical Ratings
Contact Ratings		Refer to the Contact Ratings tables below.
Dielectric Strength		1600V for one minute
		1300V for one minute (Logic Reed)
Electrical Design Life Cycles		750 000 at maximum rated load
		200 000 at maximum rated load (Logic Reed)
Mechanical Ratings
Vibration		10…2000 Hz 1.52 mm displacement (peak-to-peak) max./10 G max. (except Logic Reed)
Shock		1/2 cycle sine wave for 11 ms ³ 25 G (contact fragility) and no damage at 100 G
Degree of Protection		Type 13; IEC 144 IP65 Oiltight
Contact Operation		Contact blocks with bifurcated spanner: Slow, make and break, simple break.
		Logic Reed contact blocks: Snap-action
Typical Operating Forces		2.45 lb (10.8 N)
Operators without Contact Blocks
Contact Blocks	Standard	1.5 lb (6.7 N) 0.62 lb (2.6 N)
	Logic Reed
Environment
Temperature Range	Operating	+32…+131 °F (0…+55 °C)
	Storage	–40…+185 °F (–40…+85 °C)
Note:Operating temperatures at +32 °F (0 °C) are based on the absence of freezing moisture and liquids.
Humidity		50% at +104 °F (+40 °C)
Panel Thickness Requirements		1/16…1/4 in. (1.6…6.4 mm)
¬ Performance Data — See Performance Data.

Standard Contact Ratings

(IEC 337-1) (NEMA ICS 2-125) Maximum continuous current Ith 10 A. Bulletin 800MB units have control circuit ratings with 800M contact blocks as follows:

Max. Oprtnl. Volts Ue	Utilization Category		Rated Operational Currents
	IEC	NEMA	Volts Ue	Make	Break
AC 300	AC-II	A300	120…300 72…120 24…72 T	7200 VA 60 A 60 A	720 VA 720 VA 10 A
T For applications below 24V and 24 mA, Logic Reed contacts are recommended.

Logic Reed Contact Ratings

Maximum: 150V AC, 0.15 A, 8VA, and 30V DC, 0.06 A, 1.8VA. Should only be used with resistive loads.

Wire Capacity

Small screw contact blocks —
Accept 1 (one) #14 or 2 (two) #16 AWG solid or stranded wires.
Large screw contact blocks —
Accept 2 (two) #12 AWG wires.
Push-on connectors —
Accept 2 (two) 0.110 in x 0.032 in connectors or 1 (one) 0.250 in x 0.032 in connector.

Approximate Dimensions

Approximate Dimensions and Shipping Weights

Dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.

Extension Behind Panel for Square Units

CAUTION: To avoid possible excessive heat, clusters of nine or more continuously illuminated units mounted in a small enclosure should be spaced at 1-1/2 in. (38.1 mm) minimum centers in one direction.

Units with Quick Connect Terminal Contact Blocks (Typical View)		Units with PC Pin Connector Contact Blocks (Typical View)		Mounting Configuration¬

¬ Large screw terminal contact blocks require a minimum vertical spacing of 1-37/64 in. (40 mm); selector switches with wing lever knobs require 2-1/4 in. (57.1 mm) vertical and horizontal minimum spacing and large round legend plates require 1-1/2 in. (38.1 mm) minimum spacing.

Shipping Weights in Ounces (kg)
Type of Unit			Weight
Push buttons	Non-illuminated		3-1/4 (0.09)
	Illuminated	Full voltage	3-1/2 (0.10)
		Transformer	5 (0.14)
Pilot lights	Full voltage		2-1/4 (0.06)
	Transformer		4-1/2 (0.13)
Potentiometer units			4 (0.11)

Dimension A
Description		Quick Connect Terminal		PC Pin Connector Terminal
		Push Button	Pilot Light	Push Button	Pilot Light
Illuminated	Full voltage	2-23/32 (69.1)	2-23/32 (69.1)	—	—
	Transformer	2-1/4 (57.2)	2-1/4 (57.2)	2-5/8 (66.7)	2-5/8 (66.7)
Non-illuminated		2-1/4 (57.2)	—	2-5/8 (66.7)	—

Approximate Dimensions and Shipping Weights, Continued

Dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.

Extension Behind Panel for Square Units, Continued

CAUTION: To avoid possible excessive heat, clusters of nine or more continuously illuminated units mounted in a small enclosure should be spaced at 1-1/2 in. (38.1 mm) minimum centers in one direction.

Units Having Small Screw Terminals with Pressure Plate Contact Blocks (Typical View)		Units Having Large Screw Terminals with Pressure Plate Contact Blocks (Typical View)

Front View of Square Units

CAUTION: To avoid possible excessive heat, clusters of nine or more continuously illuminated units mounted in a small enclosure should be spaced at 1-1/2 in. (38.1 mm) minimum centers in one direction.

Unit without Insert and Backlit Unit		Square Backlit with Guarded Bezel		Square Backlit with Unguarded Bezel

Shipping Weights in Ounces (kg)
Type of Unit			Weight
Push buttons	Non-illuminated		3-1/4 (0.09)
	Illuminated	Full voltage	3-1/2 (0.10)
		Transformer	5 (0.14)
Pilot lights	Full voltage		2-1/4 (0.06)
	Transformer		4-1/2 (0.13)
Potentiometer units			4 (0.11)

Dimension A
Description		Small Screw Terminal		Large Screw Terminal
		Push Button	Pilot Light	Push Button	Pilot Light
Illuminated	Full voltage	2-25/32 (70.6)	2-25/32 (70.6)	3-11/64 (80.6)	3-11/64 (80.6)
	Transformer	2-25/32 (70.6)	2-25/32 (70.6)	3-11/64 (80.6)	3-11/64 (80.6)
Non-illuminated		2-5/16 (59)	—	2-45/64 (68.6)	—