Catalogs > Industrial Controls Catalog > Push Buttons > 22 mm > Bulletin 800FD Monolithic Push Buttons
Bulletin 800FD Monolithic Push Buttons
| Introduction |  |
Standards Compliance and Certifications | |
Product Selection | |
Accessories | |
Specifications | |
Approximate Dimensions | |
Specifications⋆
| Mechanical Ratings | ||||
| Vibration (assembled to panel) | Tested at 10…2000 Hz, 1.52 mm displacement (peak-to-peak) max./10 G max. for 3 hr duration, no damage | |||
| Shock | Tested at 1/2 cycle sine wave for 11 ms; no damage at 100 G | |||
| Degree of protection | IP66 (Type 3/3R/4/4X/12/13) | |||
| Mechanical durability per EN 60947-5-1 (Annex C) | 300 000 cycles | Selector switch | ||
| Push-pull/twist-to-release E-stop | ||||
| 2 000 000 cycles | Momentary push buttons | |||
| Operating forces | E-stop = 36 N | |||
| Operating torque (typical application with one contact block) |
Selector switch = 0.25 N•m | |||
| Contact operation | N.O. | Slow double make and break | ||
| N.C. | Slow double make and break - positive opening |
|||
|
||||
| Push button travel to change electrical state | N.O. | 2.5 mm (0.1 in.) | ||
| N.C. | 1.5 mm (0.060 in.) | |||
| Environmental | ||||
| Temperature range (operating) | -25…+60 °C (-13…+140 °F)‡ | |||
| Temperature range (short term storage) | -40…+85 °C (-40…+185 °F) | |||
| Humidity | 50…95% RH from 25…60 °C (77…140 °F) | |||
| Electrical Ratings | ||||
| Standard contact block ratings | B300, R300 AC 15, DC 13 300 VAC EN/IEC 60947-5-1 and UL 508, 17V, 5 mA min. |
|||
| Nominal Voltage | Range | Current Draw | Frequency | |
| LED module ratings | 24V AC 24V DC 120V AC 240V AC |
20…26V AC 18…30V DC 102…132V AC 204…264V AC |
32 mA 24 mA 22 mA 22 mA |
50/60 Hz DC 50/60 Hz 50/60 Hz |
| Thermal current | 5 A max. enclosed (40 °C ambient) to UL 508, EN/IEC 60947-5-1 | |||
| Insulation voltage (Ui) | 300V | |||
| Wire capacity (screw terminal) | #18…14 AWG (0.75…2.5 mm2) Max. (2) #14 AWG, uses same size wire only |
|||
| Recommendations for ring lug termination option§ | 6.35 mm (0.250 in.) Max. outer diameter with 3.8 mm (0.148 in.) hole diameter | |||
| Recommended tightening torque on screw terminals | 0.7…0.9 N•m (6…8 lb•in) | |||
| Dielectric strength (minimum) | 2500V for one minute | |||
| External short circuit protection | 5 A Type gL/gG cartridge fuse to EN 60269-2-1 or gN (Class J to UL 248-8 or Class CC to UL 248-4) | |||
| Electrical shock protection | Finger-safe conforming to IP2X | |||
| Illumination | ||||
| LED dominant wavelength | Green | 525 nm | ||
| Red | 629 nm | |||
| Yellow | 590 nm | |||
| Blue | 470 nm | |||
| White | — | |||
| LED luminous intensity | Green | 780 mcd | ||
| Red | 780 mcd | |||
| Yellow | 600 mcd | |||
| Blue | 168 mcd | |||
| White | 360 mcd | |||
| Incandescent maximum wattage | 2.6 W | |||
| ⋆ Performance Data — see Performance Data. | ||||
| ‡ Operating temperatures below 0 °C (32 °F) are based on the absence of freezing moisture and liquids. | ||||
| § 3M MV018-R/S (#22…18 AWG) or 3M MVU14-6R/S (#16…14 AWG) | ||||
Specifications, Continued⋆
| Materials | ||||
| Springs | Stainless steel and zinc coated music wire | Lens (pilot light) | Acrylic | |
| Electrical contacts | Brass with silver-nickel contacts | Bezel/bushing, housing | Glass-filled polyester | |
| Terminals | Brass and phosphor bronze | Legend frames | Glass-filled polyamide | |
| Panel gasket | Nitrile and polyester-based TPE | Mounting ring | Glass-filled polyamide | |
| Seal | Nitrile | Terminal screws | Zinc-plated steel with chromate | |
| Button cap/mushroom head | Polyester/polycarbonate blend | Lamp socket | Brass and Phosphor bronze | |
| ⋆ Performance Data — see Performance Data. | ||||