Push Buttons

Catalogs > Industrial Controls Catalog > Push Buttons > 30 mm NEMA

30 mm NEMA

Accessories

Contact Blocks

Packaged in kit form for field installation. All necessary mounting hardware is provided with each contact block kit. Contact ratings are listed on Standard Contact Ratings.

Note:It is not recommended to mount more than four contact blocks on any one non-illuminated operator, (maximum two blocks deep). Contact blocks cannot be stacked onto power modules, so illuminated operators are limited to two contact blocks. Sealed switch contact blocks are not stackable, and are limited to two blocks per operator. Time delay contacts are only available as one circuit per operator.

Contact Type	Shallow Block¬ T		PenTUFF (Low Voltage) Block¬ T		Logic Reed Block‡		Sealed Switch Block‡		Stackable Sealed Switch Block‡
	Cat. No.	Code	Cat. No.	Code	Cat. No.	Code	Cat. No.	Code	Cat. No.	Code
1 N.O.	800T-XD1	D	800T-XD1V	H	800T-XD1R	V	800T-XD1P	R	800T-XD1Y	5
1 N.C.	800T-XD2	E	800T-XD2V	U	800T-XD2R	W	800T-XD2P	S	800T-XD2Y	6
1 N.O.E.M.	800T-XD3	G	800T-XD3V	I	—	—	—	—	—	—
1 N.C.L.B.	800T-XD4	J	800T-XD4V	Q	—	—	—	—	—	—
1 N.O. - N.C.	800T-XA	A	800T-XAV	F	800T-XAR	T	800T-XAP	P	800T-XAY	7
2 N.O.	800T-XA2§	M	—	—	800T-XA2R§	Y	—	—	800T-XA2Y	8
2 N.C.	800T-XA4	N	—	—	800T-XA4R	Z	—	—	800T-XA4Y	9
1 N.C.L.B. - 1 N.O.	800T-XA1	B	—	—	—	—	—	—	—	—
1 N.C.L.B. - 1 N.C.	800T-XA7	C	—	—	—	—	—	—	—	—
Note:Modular suffix codes can be used when specifying selector switches with multiple contact blocks.

Self Monitoring Contact Block

Contact Type	S.M.C.B.¬ Ø
	Cat. No.	Code
1 N.C.L.B. (wired in series with 1 N.O. monitoring contact)	800TC-XD4S	3

Contact Type	Mini Block¬		Time Delay Block§	MaxDuty Block
	Cat. No.	Code	Cat. No.	Cat. No.	Code
1 N.O.	800T-XD5	K	800T-XT	800T-XD1M	1
1 N.C.	800T-XD6	L	800T-XS	800T-XD2M	2
1 N.C.L.B.	—	—	—	800T-XD4M	4
Note:Modular suffix codes can be used when specifying selector switches with multiple contact blocks.

¬ Contact blocks with normally closed contacts meet direct drive positive opening standard requirements when properly fused to IEC 269-1 and 269-2. Shallow/mini contacts: 10 A gl or N type cartridge fuse. PenTUFF contacts: 6 A gl or N type cartridge fuse.
T Specify Bulletin 800TC for finger-safe contact blocks. Example: Cat. No. 800T-XA becomes Cat. No. 800TC-XA.
‡ 800T operator using sealed switch and logic reed contact blocks and installed in a suitable enclosure are UL Listed as suitable for use in Class I, Division 2/Zone 2 hazardous locations.
§ Additional contacts cannot be stacked on XA2 and XA2R contact blocks.
§ For contact ratings, see Standard Contact Ratings.
Ø For use with 2-position push-pull or push-pull/twist operators only. Must be mounted on the first level of the operator. The N.O. monitoring contact automatically closes when the S.M.C.B. is properly installed onto the operator. If the S.M.C.B. is separated from the operator, the N.O. monitoring contact automatically opens.

Shallow Contact Block Hardware

Description	Cat. No.
Contact Block Mounting Screw	800T-N335
Screw Retainer	800T-N336
Actuator Extender	800T-N337

Power Modules

Packaged in kit form for field installation. Lamps are listed on Replacement Lamps.

Full Voltage Power Module Cat. No. 800T-N330		Transformer Power Module Cat. No. 800T-N326		Dual Input Power Modules Cat. No. 800T-N296 (Transformer) Cat. No. 800T-N290N (Diode)
Full Voltage§		Transformer§		Dual Input
Voltage	Cat. No.	Voltage	Cat. No.	Type	Voltage	Cat. No.
6V AC/DC 12V AC/DC 24V AC/DC 48V AC/DC 120V AC/DC	800T-N330	48V AC 50/60 Hz	800T-N325	Transformer¬	120V AC	800T-N296
		120V AC 50/60 Hz	800T-N326	Diode TypeT	24V AC/DC	800T-N291N
		240V AC 50/60 Hz	800T-N327		120V AC/DC	800T-N290N
		277V AC 50/60 Hz	800T-N327Y	—	—	—
		480V AC 50/60 Hz	800T-N328	—	—	—
240V AC/DC‡	800T-N331	600V AC 50/60 Hz	800T-N329	—	—	—
¬ Transformer type dual input provides circuit isolation via a miniature type relay. This module is used in conjunction with a 120V transformer.
T Diode type dual input provides circuit isolation via opposing diodes. Not recommended for use with solid-state outputs and neon indicators.
‡ 240V full voltage module contains 50% dropping resistors for use with a 120V incandescent lamp.
§ Specify Bulletin 800TC for finger-safe power modules. Example: Cat. No. 800T-N330 becomes Cat. No. 800TC-N330.

Resistor Power Module Cat. No. 800T-N332		Neon Power Module Cat. No. 800T-N333
Resistor (10% Drop)Ø		Neon§ Ø
Voltage	Cat. No.	Voltage	Cat. No.
120V AC/DC	800T-N332	120V AC/DC	800T-N333
		240V AC/DC	800T-N334
§ Neon modules contain resistors.
Ø Specify Bulletin 800TC for finger-safe power modules. Example: Cat. No. 800T-N332 becomes Cat. No. 800TC-N332.

Replacement Color Caps

Color caps listed below are for field replacement on installed devices or for completion of devices ordered with color caps omitted.

Push-Pull		Push-Pull/Twist		Push-Pull Jumbo		Push-Pull/Twist Jumbo

Push-Pull Color Caps, Illuminated
Color	800T Push-Pull	800H Push-Pull	800T/H Push-Pull/Twist	800T/H Push-Pull Jumbo	800T/H Push-Pull/Twist Jumbo
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Amber	800T-N159A	800H-N112A	800T-N301A	800T-N209A	800T-N306A
Blue	800T-N159B	800H-N112B	800T-N301B	800T-N209B	800T-N306B
Clear	800T-N159C	800H-N112C	800T-N301C	800T-N209C	800T-N306C
Green	800T-N159G	800H-N112G	800T-N301G	800T-N209G	800T-N306G
Red	800T-N159R	800H-N112R	800T-N301R	800T-N209R	800T-N306R
White	800T-N159W	800H-N112W	800T-N301W	800T-N209W	800T-N306W

Illuminated Mushroom		Illuminated Jumbo Mushroom		Standard		Push-to-Test		Glass Caps for Pilot Lights

Color	800T/H Push Button Color Caps, Illuminated		800T/H Pilot Light Color Caps			Glass Caps for 800T Pilot Lights
	Mushroom	Jumbo Mushroom	Standard¬	Push-to-Test¬	18 mm
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Amber	800T-N304A	800T-N305A	800T-N26A	800T-N42	800T-N122A	800T-N22
Blue	800T-N304B	800T-N305B	800T-N26B	800T-N43	800T-N122B	800T-N23
Clear	800T-N304C	800T-N305C	800T-N26C	800T-N45	800T-N122C	800T-N25
Green	800T-N304G	800T-N305G	800T-N26G	800T-N41	800T-N122G	800T-N21
Red	800T-N304R	800T-N305R	800T-N26R	800T-N40	800T-N122R	800T-N20
White	800T-N304W	800T-N305W	800T-N26W	800T-N44	800T-N122W	800T-N24
¬ Available in bulk quantities of 20. Add suffix (-BP) to the cat. no. and order in multiples of 20.

Plastic Mushroom		Plastic Jumbo Mushroom		Padlocking Metal Mushroom		Metal Jumbo Mushroom

Push Button Color Caps, Non-Illuminated
Button Color	800T Plastic Mushroom	800H Plastic Mushroom	800T Plastic Jumbo Mushroom	800H Plastic Jumbo Mushroom	800T Padlocking Metal Mushroom	800T Metal Jumbo Mushroom¬
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Red	800T-N246R	800H-N114A	800T-N247R	800H-N115A	800T-N311R	800T-N248R
Green	800T-N246G	800H-N114B	800T-N247G	800H-N115B	800T-N311G	800T-N248G
Black	800T-N246B	800H-N114H	800T-N247B	800H-N115H	800T-N311B	800T-N248B
Orange	800T-N246O	800H-N114F	800T-N247O	800H-N115F	800T-N311O	800T-N248O
Gray	800T-N246GR	800H-N114G	800T-N247GR	800H-N115G	800T-N311GR	800T-N248GR
Blue	800T-N246BL	800H-N114C	800T-N247BL	800H-N115C	800T-N311BL	800T-N248BL
Yellow	800T-N246Y	800H-N114E	800T-N247Y	800H-N115E	800T-N311Y	800T-N248Y
Natural	—	—	—	—	—	800T-N248
White	800T-N246W	800H-N114L	—	800H-N115L	—	—
¬ For padlocking jumbo mushroom style, change listed cat. no. from 248 to 313.

Push-Pull		Push-Pull/Twist		Push-Pull Jumbo		Push-Pull/Twist Jumbo

Button Color	800T/H Push-Pull Color Caps, Non-Illuminated
	Push-Pull	Push-Pull/Twist	Push-Pull Jumbo	Push-Pull/Twist Jumbo
	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Red	800T-N160A	800T-N302A	800T-N208A	800T-N307A
Green	800T-N160B	800T-N302B	800T-N208B	800T-N307B
Blue	800T-N160C	800T-N302C	800T-N208C	800T-N307C
Yellow	800T-N160E	800T-N302E	800T-N208E	800T-N307E
Orange	800T-N160F	800T-N302F	800T-N208F	800T-N307F
Gray	800T-N160G	800T-N302G	800T-N208G	800T-N307G
Black	800T-N160H	800T-N302H	800T-N208H	800T-N307H
White	800T-N160L	800T-N302L	800T-N208L	800T-N307L

Selector Switch Knobs, Illuminated

Standard Knob		Knob Lever

Color	800T Knob Type		800H Knob Type
	Standard Knob	Knob Lever	Standard Knob	Knob Lever
	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Amber	800T-N297A	800T-N298A	800H-N154A	800H-N155A
Blue	800T-N297B	800T-N298B	800H-N154B	800H-N155B
Clear	800T-N297C	800T-N298C	800H-N154C	800H-N155C
Green	800T-N297G	800T-N298G	800H-N154G	800H-N155G
Red	800T-N297R	800T-N298R	800H-N154R	800H-N155R
White	800T-N297W	800T-N298W	800H-N154W	800H-N155W

Selector Switches

		Description	Item	Color	Cat. No.
Standard Knob Lever	Coin Slot Wing Lever	800T Knobs and Actuators for Selector Switches Selector switch knobs can be changed in the field. Standard knob and knob levers can be ordered with white inserts or with a packet of colored inserts which includes one insert of each color.	Standard Knob	White	800T-N230F
				Kit	800T-N230
			Knob Lever	White	800T-N231F
				Kit	800T-N231
			Wing Lever	Gray	800T-N238
				Red	800T-N238A
			Coin Slot	Black Only	800T-N239
		800H Knob	Standard Knob	White	800H-N145F
		Description	Color	Cat. No.
		800T/H Color Insert Kits Available on Selector switches with removable color inserts. Standard knob and knob levers use the same insert. If color All is selected, a packet of color inserts will be furnished which includes one of each color. Color Insert kits can also be ordered with operators at no additional charge.	Red	800T-N124
			Green	800T-N125
			Blue	800T-N126
			Yellow	800T-N127
			White	800T-N128
			Orange	800T-N286
			All	800T-N123

Booted Selector Switch Knobs, Non-Illuminated (800H only)

Cat. No. 800H-NR5

Insert Material	Material
	Hypalon‡		Silicone ŸT ‡		Urethane ŸŸT ‡		Ethylene Ÿ Propylene ŸŸT ‡
	Cat. No.		Cat. No.		Cat. No.		Cat. No.
Brass	¬	800H-NR5	¬	800H-NR101	¬	800H-NR100	¬	800H-NR103
Stainless Steel	800HS-NR5		800HS-NR101		800HS-NR100		800HS-NR103
¬ Color insert packet (Cat. No. 800T-N123) is included in each kit.
‡ Dots printed on the inside of the boot identify the boot material.

Protective Boots

Cat. No. 800H-N11		Cat. No. 800H-N12

Protective Boot for Illuminated Push Buttons
Description	Type	Cat. No.
May be added to guarded units, units without guard or Push-to-Test devices. This protective boot guards against the entrance of foreign materials reaching the opening between the button and locking ring.	Boot without Guard	800H-N11
	Boot with Guard	800H-N12

Boots supplied with control stations and components are made of a hypalon material with brass insert ring. To order boots with silicone, urethane, or ethylene propylene material, see the table below. Material application information shown below.

Cat. No. 800H-N5A

Protective Boots for Non-llluminated Push ButtonsT
Insert Material	Boot Color	Material
		Hypalon‡	Silicone Ÿ‡	Urethane ŸŸ‡	Ethylene Ÿ Propylene ŸŸ‡
		Cat. No.	Cat. No.	Cat. No.	Cat. No.
Brass	Red	800H-N5A	800H-N101R	800H-N100R	800H-N103R
	Green	800H-N5B	800H-N101G	800H-N100G	800H-N103G
	Black	800H-N5H	800H-N101B	800H-N100B	800H-N103B
	Yellow	800H-N5E	800H-N101Y	800H-N100Y	—
	Blue	800H-N5C	800H-N101BL	800H-N100BL	—
Stainless Steel	Red	800HS-N5A	800HS-N101R	800HS-N100R	800HS-N103R
	Green	800HS-N5B	800HS-N101G	800HS-N100G	800HS-N103G
	Black	800HS-N5H	800HS-N101B	800HS-N100B	800HS-N103B
	Yellow	800HS-N5E	800HS-N101Y	800HS-N100Y	—
	Blue	800HS-N5C	800HS-N101BL	800HS-N100BL	—
T May be added to flush or extended head push button units to protect against foreign materials reaching the opening between the button and the locking ring.
‡ Dots printed on the inside of the boot identify the boot material.

Protective Boot Application Information

• Hypalon (synthetic rubber)
  Very resistant to attack by oxidizing chemicals such as concentrated sulfuric acid and hypochlorite solutions. Also resistant to attack by oils and performs well in a wide range of other chemicals and solvents. Good flex and high impact resistance. This is the standard boot material supplied with 800H NEMA Type 4/4X push buttons unless otherwise specified.
  
• Silicone
  Superior high temperature resistance. Particularly suited for use where organic acids or vegetable oils may be present. Also superior resistance to the effects of outdoor use, such as oxygen, ozone, and weather.
  
• Urethane
  Excellent resistance to mechanical failure. Most durable boot material. Particularly suited for use where lubricating oils and automotive fuels may be present. Also well-suited for outdoor use.
  
• Ethylene-propylene
  Particularly suited for high temperature applications. Resistant to attack by many acids and alkalies, detergents, phosphate esters, ketones, alcohols, and glycols. Outstanding service in areas with hot water and steam wash-downs.
  

Potentiometer Replacement Knobs

Description	Cat. No.
Type 4/13 (800T)	40274-073-55
Type 4/4X/13 (800H)	40274-073-54

Push Buttons

	Description	Cat. No.
	800T/H Mechanical Interlock Used on momentary contact push button units. Guards against closing the N.O. contacts of one button while the other button’s N.O. contacts are closed. Buttons remain momentary. For maintained units, see Mechanically Interlocked Maintained Push Button Devices.	800T-N179
Cat. No. 800T‑N179 (Operators not included)
	800T Rocker Arm Operating Lever The rocker arm lever operates two flush head or one flush with one extended head momentary contact push button units spaced 1-27/32 in. center-to-center. Legend plates must be ordered separately and should be inverted 180° prior to engraving and installation.	800T-N12
Cat. No. 800T‑N12

Miscellaneous

	Description	Cat. No.
	800T/H Mounting Ring Wrench This wrench will simplify tightening or loosening the octagonal mounting ring used on Bul. 800T units. This wrench is double‑ended and can be used for 18 mm and 30 mm pilot light mounting rings.	800T-N245
Cat. No. 800T‑N245
	800T/H Jumbo Push-Pull Cap For use on Bul. 800T or 800H push-pull operators. Fits on illuminated and non-illuminated devices.	800T-N209RE1
	800T 63 mm Red Anodized Aluminum Cap For use on Bul. 800T non-illuminated push‑pull devices.	800T-N210R
	800T 63 mm Red Anodized Aluminum Cap with "E‑Stop" For use on Bul. 800T non-illuminated push‑pull devices.	800T-N210RE
Cat. No. 800T‑N209RE1	800T 90 mm Gold Anodized Aluminum Cap For use on Bul. 800T non-illuminated push‑pull devices.	800T-N211GL
	800T Bonding Bracket The bonding bracket establishes an electrical circuit between the mounting surface and metal operator bushing for grounding purposes; recommended for installations which require CSA approval. Necessary mounting hardware is included. Order Cat. No. 800T‑N300 for back‑of‑panel bracket. Order Cat. No. 800T‑N300F for front‑of‑panel bracket.	800T-N300
Cat. No. 800T‑N300		800T-N300F
	800T/H Lens/Bulb Removal Tool The small end of this tool provides quick and easy removal of any incandescent or LED lamp.	800F-ALR1
Cat. No. 800E‑ALR1

Miscellaneous, Continued

			Description	Cat. No.
		Cat. No. 800T‑N323	800T/H IEC Finger-Safe Terminal Guards Snap-on accessories which provide IEC, IP2X and VGB finger-safe protection. Single terminal guards for single circuit contact blocks, full voltage modules, LED modules, etc. (800T-XD1, -XD2, -XD3, -XD4, -XD5, -XD6, -XAP, -XD1P, -XD2P, -PC…, and -QC…)¬  Note:Must be ordered in multiples of 100 pieces.	800T-N322
Cat. No. 800T‑N324		Cat. No. 800T‑N322	Transformer covers for transformer only. Note:Must be ordered in multiples of 25 pieces.	800T-N324
IEC Finger-Safe Accessories			Multi-terminal side cover for use on single or double circuit contact blocks. (800T-XA, -XA1, -XA2, -XA4, -XA7, -XAR, -XA2R, -XA4R, -XD1R, and -XD2R) Note:Must be ordered in multiples of 25 pieces.	800T-N323
			Gray 800T Trim Washer Used to mount the operator properly when a legend plate is not being used. Note: Must be ordered in multiples of 10 pieces.	800T-N292
			Plastic 800H Trim Washer Used to mount the operator properly when a legend plate is not being used. Note: Must be ordered in multiples of 10 pieces.	800H-N148
Cat. No. 800T-N292
			Metal 800T Thrust Washer Used to prevent rotation of operators in a keyed or notched hole. Note: Must be ordered in multiples of 10 pieces.	800T-N293
			Plastic 800H Thrust Washer Used to prevent rotation of operators in a keyed or notched hole. Note: Must be ordered in multiples of 10 pieces.	800H-N146
Cat. No. 800T-N293
			800T Etching Fluid Used to blacken freshly engraved aluminum legend plates.	800T-N188
Cat. No. 800T-N188
			Description	Color	Cat. No.
			800T/H Closing Button Where an enclosure or flush plate with more than the required number of openings is used, this neat‑appearing button can be supplied to close the unused openings.	Grey	800T-N1
Cat. No. 800T-N1				Black	800T-N1B
¬ Power modules excluding transformers and dual inputs

Locking Attachments

	Description	Cat. No.
	800T Extended Head Push Button Padlocking Attachments Permits locking in the depressed position. Locks the normally closed contact in the open position. For extended head non-illuminated momentary push buttons.	800T-N2
Cat. No. 800T‑N2 (Padlock not included)
	800T Flush Head Push Button Padlocking Attachments Permits locking in the depressed position. Locks the normally closed contact in the open position. For flush head push button.	800T-N10
Cat. No. 800T‑N10 (Padlock not included)
	800T Momentary Mushroom Padlocking Attachments For Bul. 800T non-illuminated momentary mushroom push button. Requires use of Cat. No. 800T‑N311 mushroom cap. This device is used to lock the mushroom button in a depressed position.	800T-N315
Cat. No. 800T‑N315 (Padlock not included)
	800T/H Push-Pull Padlocking Attachment For 2-position push-pull and push-pull/twist release illuminated and non-illuminated operators. Use on standard head only (40 mm dia.). Locks the normally closed contacts open only. Conversion of normally closed late break contacts to standard normally closed contacts are recommended when using this accessory. Made of stainless steel.	800T-N314
Cat. No. 800T‑N314 (Padlock not included)
	800T/H Padlocking Cover Guards against unauthorized operation for non-illuminated, standard knob selector switches and potentiometers. Stainless steel and clear plastic construction.	800T-N163
Cat. No. 800T‑N163 (Padlock not included)

Locking Attachments, Continued

	Description		Cat. No.
	800T/H Padlocking Cover Guards against unauthorized operation. For non-illuminated push buttons, 2-position push-pull or twist-release units, and standard knob selector switches. When applying Cat. No. 800H-N140 on 2-position maintained push-pull units, cover will lock only when the button is in depressed position. Padlocking cover includes blank legend plate for customer marking. Note: A pre-marked legend plate is available.The words OPEN COVER TO OPERATE are on the front and PULL-TO-START-PUSH-TO-STOP are on the rear. To order legend plate only, specify Cat. No. 800H-W174L.		800H-N140
Cat. No. 800H‑N140 (Padlock not included)
	800T 2- and 3-Position Non-illuminated Selector Switch Padlocking Attachment — Standard Knob Padlocking guard for 2- and 3-position selector switches with standard knob operators only. Locks selector switch in any maintained position.¬		800T-NX446
Cat. No. 800T‑NX446 (Padlock not included)
	Description	Position	Cat. No.
	800H 2- and 3-Position Selector Switch with Padlocking Guards Padlocking guard for 2- and 3‑position selector switches with standard knob operators only.	Left	800H-N141L
		Center	800H-N141C
		Right	800H-N141R
Cat. No. 800H‑N141R (Padlock not included)		All	800H-N141A
	800T 4-Position Selector Switch Attachment — Standard Knob Kit includes selector switch and guard (padlock not included). Padlocking guard for 4-position selector switches with standard knob operators only. Locks selector switch in any maintained position.¬		800T-NX446A
Cat. No. 800T‑NX446A (Padlock not included)
	Description	Position	Cat. No.
	800T/H Non-Illuminated Selector Switch Padlocking Attachment 2-, 3-, and 4-position selector switch padlocking attachments. Can be used to lock operators in a desired position. For 3-position selector switches, this device can also be used to lock out a left or right position as shown in the photo to the left.	For 2- and 3-Position Selector Switches
		Left	800T-N316L
		Center	800T-N316C
		Right	800T-N316R
		Window Center through Right - Prevent Left Operation	800T-N316J
		Window Center through Left - Prevent Right Operation	800T-N316K
		For 4-Position Selector Switches
		Left (Pos. 1)	800T-N317L
Cat. No. 800H‑N316J (Padlock not included)		Center Left (Pos. 2)	800T-N317CL
		Center Right (Pos. 3)	800T-N317CR
		Right (Pos. 4)	800T-N317R
	800T/H Illuminated Selector Switch Padlocking Attachment 2- and 3-position selector switch padlocking attachments for illuminated selector switches. Stainless steel material	For 2-Position Selector Switches
		Left	800T-N4162L
		Right	800T-N4162R
		For 3-Position Selector Switches
		Left	800T-N4163L
		Center	800T-N4163C
		Right	800T-N4163R
Cat. No. 800H‑N4162L (Padlock not included)		Window Center through Right - Prevent Left Operation	800T-N4163J
		Window Center through Left - Prevent Right Operation	800T-N4163K
¬ Diameter of hasp is 11/32 in. (8.73 mm)

Guards

	Description	Type	Cat. No.
	800T Push Button Guards Momentary push button guards to reduce the risk of accidental operation.	1 in. guard for non-illuminated	800T-N13
		1/2 in. guard for non-illuminated	800T-N143
		1-1/2 in. guard for illuminated	800T-N93
Cat. No. 800T-N13		1-1/2 in. guard for non-illuminated with locking attachment	800T-N39
	800H Illuminated Push Button Guard This guard provides additional protection against accidental operation of the push button unit. 1-1/2 in. (38.1 mm) guard for illumination units.		800H-N152
Cat. No. 800H-152
	800T 18 mm Guard Provides side protection for 18 mm pilot lights.		800T-N226
Cat. No. 800T-N226
	800H Stainless Steel Guard Used on non-illuminated push buttons that have protective boots as shown on Protective Boots.		800H-N153
Cat. No. 800H-N153
	800T Mushroom Push Button Guards Momentary mushroom guards for standard and jumbo mushroom push buttons. Reduces the risk of accidental operation.	Standard guard	800T-N129
		Standard guard with set screw	800T-N165
		Jumbo guard	800T-N151
Cat. No. 800T-N129		Jumbo guard with set screw	800T-N154
	Description	Type of Finish	Cat. No.
	800T/H Protective Guard Protective ring for Bul. 800T 2-position push-pull operators. Illuminated or non-illuminated. Often used to avoid unintentional tripping of E-stop operators. This guard is used with standard size button (40 mm dia.).	Stainless steel	800T-N310
Cat. Nos. 800T‑N310 and 800T‑NX1320		Black	800T-NX1320
	Description	Operator Size	Cat. No.
	800T/H Jumbo Protective Guard Protective ring for Bul. 800T 2-position push-pull operators. Illuminated or non-illuminated. Often used to avoid unintentional tripping of E-stop operators.	60 mm (Jumbo)	800T-N310J
Cat. No. 800T-N310J		63 mm	800T-N310L
	800T/H Ramp Guard For Bul. 800T/800H 2- and 3-position illuminated and non-illuminated push-pull units. Standard size button only (40 mm dia.).		800T-N339
Cat. No. 800T-N339

Replacement Lamps

Pilot Lights, Illuminated Push Buttons, Illuminated Push-Pull, Illuminated Push-Pull/Twist to Release

Lamp	Type	Current, Typical	Lamp Voltage	ANSI No.	Cat. No.
Incandescent	Full Voltage Transformer	150 mA/250 mA	6.3V AC	755/1866	¬	800T-N65
	Full Voltage	80 mA	14V AC/DC	756	¬	800T-N141
		70 mA	24V AC/DC	757	¬	800T-N157
		50 mA	48V AC/DC	1835	¬	800T-N365
	Full Voltage Resistor	22 mA	120V AC/DC	949	¬	800T-N169
	Flashing	150 mA	6V AC/DC	267	¬	800T-N212
	Dual Input Diode	57 mA	24V AC/DC	24 MB	¬	800T-N180
		21 mA	120V AC	90 MB	¬	800T-N261
Neon	—	2 mA	120V AC/DC	B2A	609-N9
Lamp	Type	Current, TypicalT	Lamp Voltage	Leakage Current	Cat. No.§
LED‡	Full Voltage	13 mA/22 mA	12V AC/DC	3 mA	800T-N362x
		13 mA/21 mA	24V AC/DC	3 mA	800T-N319x
		12 mA/17 mA	32V AC/DC	3 mA	800T-N363x
		9 mA/14 mA	48V AC/DC	3 mA	800T-N364x
		3.3 mA/6 mA	120V AC	—	800T-N320x
		4.5 mA/6.2 mA	130V AC/DC	3 mA	800T-N321x
	Transformer	50 mA	6V AC	14 mA	800T-N318x
	Flashing	18 mA	24V AC/DC	—	§	800T-N319Fx
¬ Item is sold in multiples of 5. Order quantity of 5 to receive package of 5 pieces. T Typical current draw varies with LED color. The first mA value is for a green or blue LED and the second mA value is for a red or amber LED. ‡ All LEDs except 120V have an internal shunt resistor for use with solid-state outputs. LEDs will not illuminate below listed leakage current. § To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, Blue, or White. White LEDs only available in 6V, 24V, 120V, and 130V. § Flashing rate is 2 Hz.

Illuminated Selector Switches

Lamp	Type	Current, Typical	Lamp Voltage	ANSI No.	Cat. No.¬
Incandescent	Full Voltage Transformer	150 mA/250 mA	6.3V AC	755/1866	800T-N65
	Full Voltage	80 mA	14V AC/DC	756	800T-N141
		70 mA	24V AC/DC	757	800T-N157
Lamp	Type	Current, TypicalT	Lamp Voltage	Leakage Current	Cat. No.§
LED‡	Full Voltage	13 mA/22 mA	12V AC/DC	3 mA	800T-N362x
		13 mA/21 mA	24V AC/DC	3 mA	800T-N319x
		12 mA/17 mA	32V AC/DC	3 mA	800T-N363x
		9 mA/14 mA	48V AC/DC	3 mA	800T-N364x
		3.3 mA/6 mA	120V AC	—	800T-N320x
		4.5 mA/6.2 mA	130V AC/DC	3 mA	800T-N321x
	Transformer	50 mA	6V AC	14 mA	800T-N318x
	Flashing	18 mA	24V AC/DC	—	§	800T-N319Fx

Cluster Pilot Lights

Lamp	Type	Current, Typical	Lamp Voltage	ANSI No.	Cat. No.¬
Incandescent	Full Voltage Transformer	195 mA	6V AC/DC	381	800T-N258
	Full Voltage	73 mA	12V AC/DC	382	800T-N259
		37 mA	24V AC/DC	387	800T-N260
Lamp	Type	Current, Typical	Lamp Voltage	Polarity	Cat. No.Ø
LED	Full Voltage Transformer	45 mA	6V AC/DC	Positive	800T-N340x
	Full Voltage	36 mA	12V AC/DC	Positive	800T-N341x
		14 mA	28V AC/DC	Bi-Polar	z	800T-N80x
¬ Item is sold in multiples of 5. Order quanitity of 5 to receive package of 5 pieces.
T Typical current draw varies with LED color. The first mA value is for a green or blue LED and the second mA value is for a red or amber LED.
‡ All LEDs except 120V have an internal shunt resistor for use with solid-state outputs. LEDs will not illuminate below listed leakage current.
§ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, Blue, or White. White LEDs only available in 6, 24, 120, and 130V.
§ Flashing rate is 2 Hz.
Ø To complete the cat. no., replace the x with the first letter of the desired color: Amber, Green, or Red only.
z For use with 24V AC/DC rated devices.

Replacement Keys for Cylinder Lock 2-, 3-, and 4-Position Selector Switches (800T only)

Cylinder Lock Key Option Code	Series Key Number	Cat. No.	Cylinder Lock Key Option Code	Series Key Number	Cat. No.
Blank (standard key)	D018 (standard key)	X-181170	15	T112T	40269-087-01
03	D020¬	X-307922	16	T115T	40269-087-02
04	D025¬	X-307923	17	T324T	40269-087-03
05	D335¬	X-307924	18	T382T	40269-087-04
06	D429¬	X-307925	19	T404T	40269-087-05
07	D461¬	X-307926	20	T171T	40269-087-06
08	D111¬	X-307927	21	T484T	40269-087-07
09	D587¬	X-307928	22	T547T	40269-087-08
10	D682¬	X-307929	23	T569T	40269-087-09
11	D713¬	X-307930	24	T692T	40269-087-10
12	D900¬	X-307931	25	T752T	40269-087-11
13	D992¬	X-307932	26	T178T	40269-087-12
14	D118¬	X-307933
¬ Uses master key DM81, AB Cat. No. X-433358.
T Uses master key 15T, AB Cat. No. X-433359.

Replacement Keys for Push Button Switches with Cylinder Locks (800T only)

Lock Key Option Code			Series Key Number	Cat. No.
Spring Bolt	Dead Bolt A	Dead Bolt B
Blank (standard key)	Blank (standard key)	Blank (standard key)	E158 (standard key)	X-144218
44	32	20	E109	X-386233
45	33	21	E131	X-386234
46	34	22	E100	X-386235
47	35	23	E115	X-386236
48	36	24	E120	X-386237
49	37	25	E104	X-386238
50	38	26	E108	X-386239
51	39	27	E132	X-386240
52	40	28	E144	X-386241
53	41	29	E157	X-386242
54	42	30	E101	X-386243
55	43	31	E102	40274-250-01
66	61	56	E106	40274-250-07
67	62	57	E111	40274-250-02
68	63	58	E117	40274-250-14
69	64	59	E125	40274-250-21
70	65	60	E130	40274-250-26

Blank and Custom Legend Plates — Aluminum, Type 4/13 (800T)

Blank/Custom Legend Plates

Legend Plate Color	Standard	Jumbo
	Cat. No.	Cat. No.
Grey	800T-X559	800T-X559J
Red	800T-X621	800T-X621J
Yellow	800T-X679	800T-X679J
Grey (with Custom Text)	800T-X559E	800T-X559JE
Red (with Custom Text)	800T-X621E	800T-X621JE
Yellow (with Custom Text)	800T-X679E	800T-X679JE

Specialty Legend Plates

Legend Plate Color	Automotive	Half Round¬
	Cat. No.	Cat. No.
Grey (Blank)	800T-X700	800T-X59
Red (Blank)	800T-X701	800T-X121
Grey (with Custom Text)	800T-X700E	800T-X59E
Red (with Custom Text)	800T-X701E	800T-X121E
Note:Include text with custom legends.
¬ All half round legend plates must be ordered in quantities of 25.

Custom Text Guidelines

Legend Size	No. of Lines	Max. No. of Characters per Line
Standard	1 Line of 2 Lines of	14 14
Jumbo	5 Lines	14
Automotive	4 Lines	20

Custom Legend Plates for 4 Way Toggle and Cluster Pilot Lights

Legend Size	Cat. No.‡	Color	Text OptionsT
Standard	800T-X619E	Aluminum (with Custom Text)	2 lines of up to 14 characters on top 1 line of up to 14 characters on bottom 1 vertical line of up to 7 characters on left side 1 vertical line of up to 7 characters on right side
			1 vertical line of up to 9 characters on left side 1 vertical line of up to 9 characters on right side
T Rule sets listed are mutually exclusive; only one can be chosen.
‡ For blank toggle or cluster pilot legend, order Cat. No. 800T-X619.

Blank and Custom Legend Plates — Aluminum, Type 4/13 (800T), Continued

Specialty Legend Plates

Cat. No. 800T-X618		Cat. No. 800T-X647Y		Cat. No. 800T-X646

Type	Start/Stop Legend Plates	Emergency Stop Legend Plates
	Gray	Yellow	Yellow (Large Size)	Yellow IEC Ring
	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Push-to-Stop Pull-to-Start or Push-to-Stop Twist or Pull Release	800T-X618	800T-X618Y	800T-X647Y	—
Blank	—	—	800T-X645Y	800T-X646
Custom	—	—	800T-X645YE	—
Emergency Stop	—	—	—	800T-X646EM

Potentiometer Legend Plates

Cat. No. 800T-X609		Cat. No. 800T-X608

Type	Cat. No.
Potentiometer with graduated markings	¬	800T-X609
SPEED	800T-X608
¬ For graduated markings with a custom text, order Cat. No. 800T-X609E and specify up to two lines of text, 14 characters per line.

Standard Legends – Aluminum, Type 4/13 (Bul. 800T)

Standard Legend Plate		Jumbo Legend Plate

Marking	Standard	Jumbo	Marking	Standard	Jumbo
	Cat. No.	Cat. No.		Cat. No.	Cat. No.
AUTO-OFF-HAND	800T-X501	800T-X501J	ON-OFF	800T-X622	800T-X622J
AUTO-MAN-OFF	800T-X625	800T-X625J	OPEN	800T-X531	800T-X531J
CLOSE	800T-X502	800T-X502J	OPEN-CLOSE	800T-X532	800T-X532J
CYCLE START	800T-X562	800T-X562J	OPEN-OFF-CLOSE	800T-X533	800T-X533J
DOWN	800T-X503	800T-X503J	OUT	800T-X534	800T-X534J
EMERG. STOP (Yellow)	800T-X504Y	—	POWER ON	800T-X639	800T-X639J
EMERG. STOP (Red)¬	800T-X504	800T-X504J	RAISE	800T-X535	800T-X535J
EMERGENCY STOP (Red)¬	800T-X648	800T-X648J	RAISE-LOWER	800T-X536	800T-X536J
FAST	800T-X505	800T-X505J	RAISE-OFF-LOWER	800T-X537	800T-X537J
FEED START	800T-X566	800T-X566J	RESET	800T-X538	800T-X538J
FEED STOP	800T-X567	800T-X567J	REVERSE	800T-X539	800T-X539J
FOR.-REV.	800T-X506	800T-X506J	RUN	800T-X540	800T-X540J
FOR.-OFF-REV.	800T-X507	800T-X507J	RUN-INCH	800T-X634	800T-X634J
FORWARD	800T-X508	800T-X508J	RUN-JOG	800T-X541	800T-X541
FOURTH SPEED	800T-X624	800T-X624J	SAFE-RUN	800T-X542	800T-X542J
FULL SPEED	800T-X509	800T-X509J	SECOND SPEED	800T-X543	800T-X543J
HAND-AUTO	800T-X510	800T-X510J	SPEEDT	800T-X608	—
HAND-OFF-AUTO	800T-X511	800T-X511J	SLOW	800T-X544	800T-X544J
HIGH	800T-X512	800T-X512J	SLOW-FAST	800T-X545	800T-X545J
HIGH-LOW	800T-X513	800T-X513J	SLOW-OFF-FAST	800T-X546	800T-X546J
HIGH-OFF-LOW	800T-X514	800T-X514J	START	800T-X547	800T-X547J
IN	800T-X515	800T-X515J	START-JOG	800T-X548	800T-X548J
INCH	800T-X516	800T-X516J	START-STOP	800T-X549	800T-X549J
JOG	800T-X517	800T-X517J	STOP (Red)	800T-X550	800T-X550J
JOG FORWARD	800T-X518	800T-X518J	STOP-START	800T-X551	800T-X551J
JOG REVERSE	800T-X519	800T-X519J	SUMMER-OFF-WINTER	800T-X553	800T-X553J
JOG RUN	800T-X520	800T-X520J	SUMMER-WINTER	800T-X552	800T-X552J
JOG-SAFE-RUN	800T-X522	800T-X522J	TEST	800T-X554	800T-X554J
JOG-STOP-RUN	800T-X521	800T-X521J	THIRD SPEED	800T-X555	800T-X555J
LEFT-RIGHT	800T-X523	800T-X523J	UP	800T-X556	800T-X556J
LOCAL-REMOTE	800T-X638	800T-X638J	UP-DOWN	800T-X557	800T-X557J
LOW	800T-X524	800T-X524J	UP-OFF-DOWN	800T-X558	800T-X558J
LOW SPEED	800T-X525	800T-X525J	O (Red)	800T-X640	800T-X640J
LOWER	800T-X526	800T-X526J	I	800T-X641	800T-X641J
OFF	800T-X527	800T-X527J	O I	800T-X642	800T-X642J
OFF-COOLANT-ON	800T-X528	800T-X528J	I O II	800T-X643	800T-X643J
OFF-ON	800T-X529	800T-X529J	—	—	—
ON	800T-X530	800T-X530J	—	—	—
¬ These legend plates do not comply with E-Stop standards that specify a yellow background, such as IEC 60947-5-5 and NFPA 79.
T Potentiometer type with graduated markings.

Legend Plates – Plastic, Type 4/4X/13 (800H)

Standard Legend Plate Cat. No. 800H-W100		Jumbo Legend Plate Cat. No. 800H-W100J		Automotive Legend Plate Cat. No. 800H-W100A

Blank/Custom Legend Plates Type 4/4X
Legend Plate Color	Standard	Jumbo	Automotive
	Cat. No.	Cat. No.	Cat. No.
Grey (Blank)	800H-W100	800H-W100J	800H-W100A
Red (Blank)	800H-W300	800H-W300J	800H-W300A
White (Blank)	800H-W500	800H-W500J	800H-W500A
Yellow (Blank)	800H-W700	800H-W700J	800H-W700A
Gray (with Custom Text)	800H-W100E	800H-W100JE	800H-W100AE
Red (with Custom Text)	800H-W300E	800H-W300JE	800H-W300AE
White (with Custom Text)	800H-W500E	800H-W500JE	800H-W500AE
Yellow (with Custom Text)	800H-W700E	800H-W700JE	800H-W700AE
Note:Include text with custom legends.

Custom Text Guidelines

Legend Size	Number of Lines	Maximum Number of Characters per Line
Standard	1 Line of 2 Lines of	13 13
Jumbo	5 Lines	13
Automotive	4 Lines	16

Blank Legend Plate Cat. No. 800H-W1		Potentiometer Legend Plate Cat. No. 800H-W080

Legend Plates — Type 4 Flip Lever¬		Potentiometer Legends
Legend Plate Color	Cat. No.	Legend Marking	Cat. No.
White (Blank)	800H-W1	Graduated Markings Only	800H-W080
Red (Blank)	800H-W40	SPEED	800H-W081
White (with Custom Text)	800H-W1E	Custom Legend with Graduated Marking	800H-W080E
Red (with Custom Text)	800H-W40E
¬ 1 line, 11 characters, maximum.

Cat. No. 800H-W196		Cat. No. 800H-W797A		Cat. No. 800H-W690

	Start/Stop Legend Plates	Emergency Stop Legend Plates
Type	Gray	Yellow (Large Size)	Yellow IEC Ring
	Cat. No.	Cat. No.	Cat. No.
Push-to-Stop Pull-to-Start	800H-W196	800H-W797A	—
Blank	—	800H-W700A	800H-W690
Custom	800H-W100E	800H-W700AE	—

Standard Legend Plates – Plastic, Type 4/4X/13 (800H)

Grey Legend Plate Type 4/4X		White Legend Plate Type 4/4X

Marking	Gray Type 4/4X	White Type 4/4X	Marking	Gray Type 4/4X	White Type 4/4X
	Cat. No.	Cat. No.		Cat. No.	Cat. No.
AUTO OFF HAND	800H-W154	800H-W554	LOWER	800H-W115	800H-W515
AUTO MAN HAND	800H-W059	800H-W459	MAN AUTO	800H-W031	800H-W431
CLOSE	800H-W101	800H-W501	MAN OFF AUTO	800H-W062	800H-W462
CYCLE START	800H-W006	800H-W406	MOTOR RUN	800H-W008	800H-W408
CYCLE STOP (Red)	800H-W376	—	MOTOR STOP (Red)	800H-W375	—
DECREASE	800H-W002	800H-W402	OFF	800H-W116	800H-W516
DOWN	800H-W102	800H-W502	OFF COOLANT ON	800H-W052	800H-W452
EMERG. STOP (Red)¬	800H-W372	—	OFF LOC REMOTE	800H-W061	—
EMERGENCY STOP (Red)¬	800H-W373	—	OFF MAN AUTO	800H-W060	800H-W460
FAST	800H-W104	800H-W504	OFF ON	800H-W133	800H-W533
FEED START	800H-W007	—	ON	800H-W117	800H-W517
FEED STOP (Red)	800H-W377	—	OPEN	800H-W118	800H-W518
FOR. REV.	800H-W132	800H-W532	OPEN CLOSE	800H-W134	800H-W534
FOR. OFF REV.	800H-W152	800H-W552	OPEN OFF CLOSE	800H-W153	800H-W553
FORWARD	800H-W105	800H-W505	OUT	800H-W119	800H-W519
FOURTH SPEED	800H-W010	—	POWER ON	800H-W001	800H-W401
FULL SPEED	800H-W106	800H-W506	PULL-TO-START	800H-W198	—
HAND AUTO	800H-W131	800H-W531	PUSH-TO-STOP (Red)	800H-W378	—
HAND OFF AUTO	800H-W151	800H-W551	RAISE	800H-W120	800H-W520
HIGH	800H-W107	800H-W507	RAISE LOWER	800H-W034	—
HIGH LOW	800H-W030	—	RAISE OFF LOWER	800H-W156	800H-W556
HIGH LOW OFF	800H-W058	—	RESET	800H-W121	800H-W521
HIGH OFF LOW	800H-W155	800H-W555	REVERSE	800H-W122	800H-W522
IN	800H-W108	800H-W508	RIGHT	800H-W005	800H-W405
INCH	800H-W109	800H-W509	RUN	800H-W123	800H-W523
INCREASE	800H-W003	—	RUN INCH	800H-W037	—
JOG	800H-W110	800H-W510	RUN JOG	800H-W032	—
JOG FORWARD	800H-W111	800H-W511	SAFE RUN	800H-W033	—
JOG REVERSE	800H-W112	800H-W512	SECOND SPEED	800H-W124	800H-W524
JOG RUN	800H-W135	800H-W535	SLOW	800H-W125	800H-W525
JOG SAFE RUN	800H-W051	—	SLOW FAST	800H-W136	800H-W536
JOG STOP RUN	800H-W057	—	SLOW OFF FAST	800H-W157	800H-W557
LEFT	800H-W004	800H-W404	SPEEDT	800H-W081	800H-W481
LEFT RIGHT	800H-W036	—	SPEEDT	800H-W182	—
LOC OFF REMOTE	800H-W055	800H-W455	START	800H-W126	800H-W526
LOW	800H-W113	800H-W513	START JOG	800H-W138	800H-W538
LOW HIGH	800H-W035	—	START JOG STOP	800H-W158	800H-W558
LOW OFF HIGH	800H-W056	—	START RUN STOP	800H-W054	—
LOW SPEED	800H-W114	800H-W514	START STOP	800H-W137	800H-W537
¬ These legend plates do not comply with E-Stop standards that specify a yellow background, such as IEC 60947-5-5 and NFPA 79.
T Potentiometer type with graduated markings.

Standard Legend Plates – Plastic, Type 4/4X/13 (800H)

Grey Legend Plate Type 4/4X		White Legend Plate Type 4/4X

Marking	Gray Type 4/4X	White Type 4/4X	Marking	Gray Type 4/4X	White Type 4/4X
	Cat. No.	Cat. No.		Cat. No.	Cat. No.
UP	800H-W009	800H-W409	STOP (Red)	800H-W371	—
UP DOWN	800H-W039	—	STOP RUN START	800H-W053	—
UP OFF DOWN	800H-W160	800H-W560	STOP START	800H-W038	800H-W438
O (Red)	800H-W184	—	SUMMER OFF WINTER	800H-W159	800H-W559
O I	800H-W185	800H-W582	SUMMER WINTER	800H-W139	800H-W539
I	800H-W181	800H-W581	TEST	800H-W128	800H-W528
I O II	800H-W183	800H-W583	THIRD SPEED	800H-W129	800H-W529

Flip Lever Legend Plates

Flip Lever Legend Plate Type 4

Marking	Flip Lever — Type 4	Marking	Flip Lever — Type 4
	Cat. No.		Cat. No.
CLOSE	800H-W3	OPEN	800H-W18
DOWN	800H-W5	OUT	800H-W19
EMERG. STOP (Red)	800H-W42	RAISE	800H-W20
FAST	800H-W6	RESET	800H-W21
FORWARD	800H-W7	REVERSE	800H-W22
FULL SPEED	800H-W35	RIGHT	800H-W23
HIGH	800H-W9	RUN	800H-W24
IN	800H-W10	SECOND SPEED	800H-W33
INCH	800H-W11	SLOW	800H-W26
JOG	800H-W12	START	800H-W27
LEFT	800H-W13	STOP (Red)	800H-W41
LOW	800H-W14	TEST	800H-W29
LOW SPEED	800H-W32	THIRD SPEED	800H-W34
LOWER	800H-W15	UP	800H-W30
OFF	800H-W16	O	800H-W36
ON	800H-W17	I	800H-W37