Catalogs > Industrial Controls Catalog > Push Buttons > Hazardous Location > Bulletin 800H Type 7&9 Hazardous Location Push Buttons

Bulletin 800H Type 7&9 Hazardous Location Push Buttons

Introduction

Standards Compliance and Certifications

Product Selection

Product Selection for Stations

Modifications and Accessories

Pilot Light Wiring Diagrams

Specifications

Approximate Dimensions

Product Selection

Complete Assembled Stations (Supplied with 3/4 in. Dead End Conduit Entry — Cat. No. 800H‑1HZX7)

	Operator	Contact Symbol		Contact Action	Legend Marking	Lever Type Actuator⋆ §	Component Type Buttons‡ §
	Operator	Contact Symbol		Contact Action	Legend Marking	Cat. No.	Cat. No.
	One Push Button		1 N.O. 1 N.C.	Momentary	STOP	800H-1HA7	800H-1HA7P
					START	800H-1HB7	800H-1HB7P
					JOG	800H-1HJ7	800H-1HJ7P
Cat. No. 800H‑1HA7					No Legends	800H-1HX7	800H-1HX7P
	Two Push Buttons		1 N.O. 1 N.C. Each Button	Momentary	START STOP	800H-2HA7	800H-2HA7P
					FOR REV	800H-2HB7	800H-2HB7P
					RAISE LOWER	800H-2HD7	800H-2HD7P
					OPEN CLOSE	800H-2HF7	800H-2HF7P
Cat. No. 800H‑2HA7P		Each Button			No Legends	800H-2HX7	800H-2HX7P
	2-Position Selector Switch		1 N.O. 1 N.C.	Maintained	START STOP	800H-2HAM7	—
					ON OFF	800H-2HCM7	800H-R2HC7
					OPEN CLOSE	800H-2HGM7	800H-R2HG7
					RUN STOP	800H-2HJM7	—
					HAND AUTO	800H-2HLM7	800H-R2HA7
Cat. No. 800H‑2HAM7					No Legends	800H-2HXM7	800H-R2HX7
	3-Position Selector Switch		1 N.O. 1 N.C.	—	HAND OFF AUTO	—	800H-R3HA7
Cat. No. 800H‑R3HA7	3-Position Selector Switch		1 N.O. 1 N.C.	—	No Legends	—	800H-R3HX7
	One Pilot Light, Dual Push Buttons		120V AC/DC Full Volt./Red	—	No Legend START STOP	—	800H-2HAD10R7
Cat. No. 800H‑2HAD10R7	One Pilot Light, Dual Push Buttons		1 N.O. 1 N.C.	—	Marking other than listed - consult your local Allen-Bradley distributor	—	800H-2HXD10R7

⋆ Operators have integral padlocking attachment.
‡ STOP is extended red, START is flush green, all others are flush black.
§ Supplied with standard shallow contact blocks. For stations with sealed switch contacts, change Bulletin number from 800H to 800R. A deep enclosure is required.

Momentary Contact Push Button Units, Non-Illuminated


Flush Head Unit Cat. No. 800H-AP1A		Extended Head Unit Cat. No. 800H-BP6B		Mushroom Head Unit Cat. No. 800H-DP6A

Contact Type		Button Color	Flush Head	Extended Head	Mushroom Head
Contact Type		Button Color	Cat. No.⋆	Cat. No.⋆	Cat. No.⋆
No Contact		Green	800H-AP1	800H-BP1	800H-DP1
		Black	800H-AP2	800H-BP2	800H-DP2
		Red	800H-AP6	800H-BP6	800H-DP6
	1 N.O.	Green	800H-AP1D1	800H-BP1D1	800H-DP1D1
		Black	800H-AP2D1	800H-BP2D1	800H-DP2D1
		Red	800H-AP6D1	800H-BP6D1	800H-DP6D1
	1 N.C.	Green	800H-AP1D2	800H-BP1D2	800H-DP1D2
		Black	800H-AP2D2	800H-BP2D2	800H-DP2D2
		Red	800H-AP6D2	800H-BP6D2	800H-DP6D2
	1 N.O. - 1 N.C.	Green	800H-AP1A	800H-BP1A	800H-DP1A
		Black	800H-AP2A	800H-BP2A	800H-DP2A
		Red	800H-AP6A	800H-BP6A	800H-DP6A
	2 N.O. - 2 N.C.	Green	800H-AP1B	800H-BP1B	800H-DP1B
		Black	800H-AP2B	800H-BP2B	800H-DP2B
		Red	800H-AP6B	800H-BP6B	800H-DP6B

⋆ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-AP1.

Dual Momentary Contact Push Button Units

Dual Push Button Unit
Cat. No. 800H-DPH16AXX64

Contact Arrangement		Legend Marking		Cat. No.‡
Type	Contacts	Left	Right	Cat. No.‡
2 N.O. - 2 N.C.		START (Flush/Green)	STOP (Extended/Red)	800H-DPH16AAXX64
		ON (Flush/Black)	OFF (Flush/Black)	800H-DPH22AAXX50
		OPEN (Flush/Black)	CLOSE (Flush/Black)	800H-DPH22AAXX57
		UP (Flush/Black)	DOWN (Flush/Black)	800H-DPH22AAXX66
		Blank (Flush/Black)	Blank (Flush/Black)	800H-DPH22AAXX

‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-DPH16AAXX64.

Momentary Contact Push Button Units, Non-Illuminated

800		H	–	AP		1				A
		a		b		c		d		e

a		b		c
Barrel Type		Operator Type		Color Cap
Code	Description	Code	Description	Code	Description
H	Standard barrel length	AP	Flush head	Blank	Used only when ordering operator type DPX (Table b)
HL	Long barrel	BP	Extended head	1	Green
		DP	Mushroom head	2	Black
		DPX	Mushroom head less color cap	3	Orange
				4	Grey
				6	Red
				7	Blue
				9	Yellow

d		e
Special Mushroom Head		Contact Block(s)⋆
Code	Description	Standard
Blank	No special head	Code	Description
J	Jumbo mushroom head — plastic	Blank	No contacts
L	Jumbo mushroom head — metal	D1	1 N.O.
Note: Special mushroom head options only apply to mushroom head operator type DP (Table b).		D2	1 N.C.
		D5	1 N.O. (Mini)
		D6	1 N.C. (Mini)
		A2	2 N.O.
		A4	2 N.C.
		A	1 N.O. - 1 N.C.
		B	2 N.O. - 2 N.C.
		H	3 N.O. - 3 N.C.
		C	4 N.O. - 4 N.C.
		PenTUFF (Low Voltage)
		D1V	1 N.O.
		D2V	1 N.C.
		AV	1 N.O. - 1 N.C.
		BV	2 N.O. - 2 N.C.
		HV	3 N.O. - 3 N.C.
		CV	4 N.O. - 4 N.C.

Note:Special mushroom head options only apply to mushroom head operator type DP (Table b).

Dual Push Button Units

800

–

AAXX

a		b		c		d
Barrel Type		Operator Type		Mounting		Color of Button
Code	Description	Code	Description	Code	Description	Code	Description
H	Standard barrel	DP	Dual push button	H	Horizontal	16	Left green flush/right red extended
HL	Long barrel			B	Vertical	22	Left black flush/right black flush

e			f
Contact Block(s)⋆			Marking
Code	Contact Arrangement		Code	Description
Code	Left button for horizontal Top button for vertical	Right button for horizontal Bottom button for vertical	Code	Left button for horizontal Top button for vertical	Right button for horizontal Bottom button for vertical
AAXX	1 N.O. - 1 N.C.	1 N.O. - 1 N.C.	Blank	No mark specified	No mark specified
AAAA	2 N.O. - 2 N.C.	2 N.O. - 2 N.C.	64	START	STOP
			50	ON	OFF
			51	FORWARD	REVERSE
			57	OPEN	CLOSE
			66	UP	DOWN
			99‡	Marking specified	Marking specified

⋆ For sealed switch and Logic Reed contact blocks, see Modifications and Accessories.
‡ To order with special marking, specify marking; seven characters maximum per button, single line only.

Momentary Contact Push Button Units, Illuminated

Extended Head with Guard
Cat. No. 800H-PPB16M

Type	Lamp	Supply Voltage	Lens Color∆	Extended Head with Guard
				Cat. No.♣ &
Operator only♦				800H-QPB00XX
Full Voltage	Incandescent	24V AC/DC	Multi-color kit	800H-QPB24M
		120V AC/DC		800H-QPB10M
No lamp	0…250V AC/DC	No lens	800H-QPBN25
Universal	LED	12…130V AC/DC	Multi-color kit	800H-QPBH2M
Transformer	Incandescent	120V AC 50/60 Hz	Multi-color kit	800H-PPB16M
	LED			800H-PPBH16M
	No lamp		No lens	800H-PPBN16

∆ Units ship with multi-color insert packet including amber, blue, green, red, and white.
♣ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-QPB2M.
& Includes as standard one Cat. No. 800T-XA (1 N.O./1 N.C.) contact block.
♦ Operator only supplied without power module, lamp, lens cap, or contact blocks.

Potentiometer Units§

Potentiometer Unit
Cat. No. 800H-UP24

Resistance	Potentiometer⋆	Resistance	Potentiometer⋆
	Cat. No.♠		Cat. No.♠
Operator Only (without Resistive Element)	800H-NP37‡	2.5 kW	800H-UP19
		5 kW	800H-UP24
1 kW	800H-UP13	10 kW	800H-UP29

⋆ Rated for 300V AC/DC, 2W maximum.
‡ For use with Type J potentiometers having a shaft length of 7/8 in. (22.2 mm) and a shaft diameter of 1/4 in. (6.3 mm).
§ Single-turn operation with 312° rotation.
♠ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-UP13.

Momentary Contact Push Button Units, llluminated

800

–

PPB

a		b
Operator Type		Power Module Type
Code	Description	Code	Description
H	Standard barrel length	PPB	Transformer (or dual input)
HL	Long barrel	QPB	Full voltage/Universal

c		d
Illumination Options		Voltage
Illumination Options		Transformer
Code	Description	Code	Description
Blank	Incandescent	16	120V AC 50/60 Hz
H	LED	26	240V AC 50/60 Hz
Dual Input		46	480V AC 50/60 Hz
D	Diode type, incandescent♣	56	600V AC 50/60 Hz
T	Transformer — relay type, incandescent	Full Voltage — Incandescent
TH	Transformer — relay type, LED	24	24V AC/DC
		10	120V AC/DC
		20	240V AC/DC
		Universal — LED
		2	12…130V AC/DC
		Dual Input
		16	120V AC
		24	24V AC/DC♠

e		f
Lens Color		Contact Block(s)∇
Code	Color	Standard
Blank	No lens, with standard contacts 1 N.O. - 1 N.C.	Code	Description
X	No lens if ordering any contacts other than standard 1 N.O. - 1 N.C.	Blank	1 N.O. - 1 N.C.
M	Multi-color⋆	X	No contacts
		D1	1 N.O.
		D2	1 N.C.
		A2	2 N.O.
		A4	2 N.C.
		PenTUFF (Low Voltage)
		D1V	1 N.O.
		D2V	1 N.C.
		AV	1 N.O. - 1 N.C.

♣ Diode type dual input provides circuit isolation via opposing diodes. Not recommended for use with solid-state outputs and neon indicators.
♠ Dual input diode only.
⋆ Multi-color insert packet includes amber, blue, green, red, and white.
∇ For sealed switch and Logic Reed contact blocks, see Modifications and Accessories.

2-Position Push-Pull Units, Non-Illuminated

2-Position Push-Pull
Cat. No. 800H-FPX6A5

Contact Type		Operator Position		Button Color	Push-Pull

		Maintained	Maintained
		Out	In		Cat. No.⋆
	N.C.L.B.	X	O	Red	800H-FPX6D4
	N.O. - N.C.L.B.	O X	X O	Red	800H-FPX6A1
	N.C.L.B. - N.C.L.B.	X X	O O	Red	800H-FPX6A5

Note:X = Closed/O = Open
⋆ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-FPX6D4.

3-Position Push-Pull Units, Non-Illuminated

3-Position Push-Pull
Cat. No. 800H-FPXM6A7

Contact Type		Operator Position			Button Color	Push-Pull

		Momentary	Maintained	Maintained
		Out	Center	In		Cat. No.‡
	N.C. - N.C.L.B.	X X	O X	O O	Red	800H-FPXM6A7

‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-FPXM6A7.

Contact Type		Operator Position			Button Color	Push-Pull

		Momentary	Maintained	Momentary
		Out	Center	In		Cat. No.‡
	N.C. - N.C.L.B.	X X	O X	O O	Red	800H-FPXN6A7

Note:X = Closed/O = Open
‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-FPXM6A7.

2-Position Push-Pull Units, Non-Illuminated

800		H	–	FPX				1		A1
		a		b		c		d		e

a		b		c		d
Barrel Type		Operator Type		Head Type		Color Cap
Code	Description	Code	Description	Code	Description	Code	Color
H	Standard barrel length	FPX	Push-pull unit	Blank	Mushroom head	Blank	No cap
HL	Long barrel			J	Jumbo mushroom head⋆	1	Green
						2	Black
						4	Grey (silver)
						6	Red
						7	Blue
						9	Yellow (gold)

e
Contact Block(s)
Standard
Code	Operator Position		Description

	Out	In
Blank	—	—	No contacts
A1	O X	X O	1 N.O. - 1 N.C.L.B.⋆
A5	X X	O O	2 N.C.L.B.⋆
D1	O	X	1 N.O.
D4	X	O	1 N.C.L.B.⋆
PenTUFF (Low Voltage)
D1V	O	X	1 N.O.
AV	O X	X O	1 N.O. - 1 N.C.
Note: X = Closed/O = Open.

⋆ Normally closed late break contact. When button is pushed from the OUT to the IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs.

3-Position Push-Pull Units, Non-Illuminated

800

–

FPX

a		b		c
Barrel Type		Operator Type		Head Type
Code	Description	Code	Description	Code	Description
H	Standard barrel length	FPX	Push-pull unit	Blank	Mushroom head
HL	Long barrel			J	Jumbo mushroom head‡

Operator Function

Color Cap

Contact Block(s)

Code

Operator Position

Code

Color

Standard

Blank

No cap

Code

Operator Position

Description

Out

Center

Green

Momentary

Maintained

Black

Out

Ctr.

Momentary

Maintained

Momentary

Grey (silver)

Blank

—

No contacts

Red

O
X

O
O

X
O

1 N.O. -
1 N.C.

Blue

O
X

X
O

1 N.O. -
1 N.C.L.B.

Yellow (gold)

X
X

O
X

O
O

1 N.C. -
1 N.C.L.B.

X
X

O
X

O
O

2 N.C. -
2 N.C.L.B.

PenTUFF (Low Voltage)

O
X

O
O

X
O

1 N.O. -
1 N.C.

Note: X = Closed/O = Open.

‡ Not valid with color cap option Blank (no cap).

2-Position Push-Pull Units, Illuminated

Illuminated 2-Position Push-Pull
Cat. No. 800H-FPXP16RA1

Type	Lamp Type	Supply Voltage	Lens Color⋆	Contacts	Operator Position		Cat. No.‡

					Maintained	Maintained
					Out	In
Operator only§				No contacts			800H-FPXQ00
Full voltage	Incandescent	24V AC/DC	Multi-color kit	N.O. - N.C.L.B.	O X	X O	800H-FPXQ24MA1
		120V AC/DC					800H-FPXQ10MA1
No lamp	0…250V AC/DC	No lens	No contacts			800H-FPXQN25
Universal	LED	12…130V AC/DC	Multi-color kit	N.O. - N.C.L.B.	O X	X O	800H-FPXQH2MA1
Transformer	Incandescent	120V AC, 50/60 Hz	Multi-color kit	N.O. - N.C.L.B.	O X	X O	800H-FPXP16MA1
	LED						800H-FPXPH16MA1
	No lamp		No lens	No contacts			800H-FPXPN16

Note:X = Closed/O = Open.
⋆ Units ship with multi-color insert packet including amber, blue, green, red, and white.
‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-FPXQH2MA1.
§ Operator only supplied without power module, lamp, lens cap, or contact blocks.

3-Position Push-Pull Units, Illuminated

Illuminated 3-Position Push-Pull
Cat. No. 800H-FPXMP16RA7

Operator Position (800H-FPXM)				Operator Position (800H-FPXN)

	Momentary	Maintained	Maintained		Momentary	Maintained	Momentary
Contacts	Out	Center	In	Contacts	Out	Center	In
N.C. - N.C.L.B.	X	O	O	N.C. - N.C.L.B.	X	O	O
N.C. - N.C.L.B.	X	X	O	N.C. - N.C.L.B.	X	X	O

Type	Lamp Type	Supply Voltage	Lens Color⋆	Cat. No.‡	Cat. No.‡
Operator only§				800H-FPXMQ00	800H-FPXNQ00
Full voltage	Incandescent	24V AC/DC	Multi-color kit	800H-FPXMQ24MA7	800H-FPXNQ24MA7
Full voltage	Incandescent	120V AC/DC	Multi-color kit	800H-FPXMQ10MA7	800H-FPXNQ10MA7
No lamp	0…250V AC/DC	No lens	800H-FPXMQN25	800H-FPXNQN25
Universal	LED	12…130V AC/DC	Multi-color kit	800H-FPXMQH2MA7	800H-FPXNQH2MA7
Transformer	Incandescent	120V AC, 50/60 Hz	Multi-color kit	800H-FPXMP16MA7	800H-FPXNP16MA7
	LED		Multi-color kit	800H-FPXMPH16MA7	800H-FPXNPH16MA7
	No lamp		No lens	800H-FPXMPN16	800H-FPXNPN16

Note:X = Closed/O = Open
⋆ Units ship with multi-color insert packet including amber, blue, green, red, and white.
‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-FPXQH2MA1.
§ Operator only supplied without power module, lamp, lens cap, or contact blocks.

2- and 3-Position Push-Pull Units, Illuminated

800

–

FPX

a		b
Barrel Type		Operator Type
Code	Description	Code	Description
H	Standard barrel length	FPX	Push-pull unit
HL	Long barrel

c				d
Operator Function				Illumination Options
2-Position				Transformer
Code	Description			Code	Description
Blank	Push-Pull			P	Incandescent
3-Position				PH	LED
Code	Operator Position			Full Voltage
				Q	Incandescent
	Out	Ctr.	In	QH	Universal LED
M	Mom.	Main.	Main.	Dual Input
N	Mom.	Main.	Mom.	D	Dual input — diode♣
Mom - Momentary Main - Maintained				DT	Dual input — transformer relay
				DTH	Dual input transformer — relay LED

e (cont'd)

g (cont'd)

Voltage

Color Cap

Contact Blocks

Transformer

Universal — LED

Standard

PenTUFF (Low Voltage)

Code

Description

Code

Description

Code

Color

Code

Color

Code

Description

120V AC 50/60 Hz

12…130V AC/DC

Blank

No lens with no contacts

Blank

No contacts

D1V

1 N.O.

240V AC 50/60 Hz

Dual Input

No lens with contacts

1 N.O.

D2V

1 N.C.

480V AC 50/60 Hz

120V AC

Multi-color⋆

1 N.C.L.B.♠

1 N.O. - 1 N.C.

600V AC 50/60 Hz

24V AC/DC∇

1 N.O. - 1 N.C.

Logic Reed

Full Voltage — Incandescent

1 N.O. -
1 N.C.L.B.♠

D1R

1 N.O.

24V AC/DC

2 N.O.

D2R

1 N.C.

120V AC/DC

2 N.C.L.B.

1 N.O. - 1 N.C.

240V AC/DC

1 N.C. -
1 N.C.L.B.♠

A2R

2 N.O.

A4R

2 N.C.

Note:Mom. - Momentary
Main. - Maintained

Table 1. Target Selection

2-Position			Contact Description	3-Position
g Code							g Code
g Code	Out	In		Out	Center	In	g Code
A, AV, R	O	X	N.O. N.C.	O	O	X	A, AV, AR
A, AV, R	X	O	N.O. N.C.	X	O	O	A, AV, AR
A1	O	X	N.O. N.C.L.B.	O	O	X	A1
A1	X	O	N.O. N.C.L.B.	X	X	O	A1
A2	O	O	N.O. N.O.	—	—	—	—
A2	X	X	N.O. N.O.	—	—	—	—
A5	X	X	N.C.L.B N.C.L.B	—	—	—	—
A5	O	O	N.C.L.B N.C.L.B	—	—	—	—
—	—	—	N.C. N.C.L.B.	X	O	O	A7
—	—	—	N.C. N.C.L.B.	X	X	O	A7
D1, D1V, D1R	O	X	N.O.	—	—	—	—
D4	X	O	N.C.L.B.	—	—	—	—

⋆ Multi-color insert packet includes amber, blue, green, red, and white.
♣ Diode type dual input provides circuit isolation via opposing diodes. Not recommended for use with solid-state outputs and neon indicators.
♠ Normally closed late break contact. When button is pushed from the OUT to the IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs.
∇ Dual input diode only.

2-Position Selector Switch Units, Non-Illuminated


Standard Knob Operator Cat. No. 800H-HP2KB6AXXX		Knob Lever Operator Cat. No. 800H-HP17KB6AXXX		Metal Wing Lever Operator Cat. No. 800H-HP11KBAXXX

Contact Type		Operator Position		Contact Action M = Maintained S = Spring Return	Standard Knob	Knob Lever	Wing Lever
Contact Type				Contact Action M = Maintained S = Spring Return	Cat. No.§	Cat. No.§	Cat. No.§
No Contacts		—	—	M M	800H-HP2KB6	800H-HP17KB6	800H-HP11KB6
No Contacts		—	—	S→M⋆	800H-HP4KL8	800H-HP4KL8	800H-HP4KL8
	1 N.O.	O	X	M M	800H-HP2KB6DXXX	800H-HP17KB6DXXX	800H-HP11KB6DXXX
				S→M⋆	800H-HP4KL8DXXX	800H-HP18KL8DXXX	800H-HP15KL8DXXX
				M←S	800H-HP5KL8DXXX	800H-HP19KL8DXXX	800H-HP16KL8DXXX
	1 N.O. - 1 N.C.	O X	X O	M M	800H-HP2KB6AXXX	800H-HP17KB6AXXX	800H-HP11KB6AXXX
				S→M⋆	800H-HP4KL8AXXX	800H-HP18KL8AXXX	800H-HP15KL8AXXX
				M←S	800H-HP5KL8AXXX	800H-HP19KL8AXXX	800H-HP16KL8AXXX
	2 N.O. - 2 N.C.	O X O X	X O X O	M M	800H-HP2KB6AAXX	800H-HP17KB6AAXX	800H-HP11KB6AAXX
				S→M⋆	800H-HP4KL8AAXX	800H-HP18KL8AAXX	800H-HP15KL8AAXX
				M←S	800H-HP5KL8AAXX	800H-HP19KL8AAXX	800H-HP16KL8AAXX

Note:X = Closed/O = Open
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-HP4KL8.

2-Position Cylinder Lock Operator
Cat. No. 800H-HP31KB6AXXX

Contact Type		Operator Position		Contact Action M = Maintained S = Spring Return	Cylinder Lock
					Key Removal Left‡	Key Removal Right‡	Key Removal Both‡
					Cat. No.§	Cat. No.§	Cat. No.§
No Contacts		—	—	M M	800H-HP31KB6	800H-HP32KB6	800H-HP33KB6
				M←S	800H-HP48KL8	—	—
	1 N.O.	O	X	M M	800H-HP31KB6DXXX	800H-HP32KB6DXXX	800H-HP33KB6DXXX
				S→M⋆	—	800H-HP42KL8DXXX	—
				M←S	800H-HP48KL8DXXX	—	—
	1 N.O. - 1 N.C.	O X	X O	M M	800H-HP31KB6AXXX	800H-HP32KB6AXXX	800H-HP33KB6AXXX
				S→M⋆	—	800H-HP42KL8AXXX	—
				M←S	800H-HP48KL8AXXX	—	—
	2 N.O. - 2 N.C.	O X O X	X O X O	M M	800H-HP31KB6AAXX	800H-HP32KB6AAXX	800H-HP33KB6AAXX
				S→M⋆	—	800H-HP42KL8AAXX	—
				M←S	800H-HP48KL8AAXX	—	—

Note:X = Closed/O = Open
⋆ Target tables are reversed from those shown.
‡ Key removable from maintained positions only. Devices supplied with 2 keys. Replacement part number for standard D018 key is X-181170.
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-HP48KL8.

2-Position Selector Switch Units, Non-Illuminated

800

–

KB6

AXXX

(Knob/Wing Lever)

800

–

KB6

AXXX

c₁

d₁

(Cylinder Lock)

a		b		c
Barrel Type		Number of Positions		Knob Insert Colors⋆
Code	Description	Code	Description	Code	Color
H	Standard barrel length	HP	2-position	Blank	White
HL	Long barrel			X	Packet of colored inserts‡
				Metal Wing Lever Colors
				Code	Color
				A	Red
				Blank	Grey

c₁		d
Key Removal Position		Operator Type and Function
Maintained		Standard Knob
Code	Operator Function	Code	Operator Function
31	Key removal — left	2	Maintained
32	Key removal — right	4	Spring return from left§
33	Key removal — both	5	Spring return from right
Spring Return From Left		Knob Lever
Code	Operator Function	Code	Operator Function
42	Key removal — right§	17	Maintained
Spring Return From Right		18	Spring return from left§
Code	Operator Function	19	Spring return from right
48	Key removal — left	Metal Wing Lever
		Code	Operator Function
		11	Maintained
		15	Spring return from left§
		16	Spring return from right

d₁				e
Optional Keys				Cam Option
Code	D Series Key No.	Code	T Series Key No.	Code	Description
Blank	D018 (std. key)	15	T112	KB6	Cam for maintained operators
03	D020	16	T115	KL8	Cam for spring return operators
04	D025	17	T324
05	D335	18	T382
06	D429	19	T404
07	D461	20	T171
08	D111	21	T484
09	D587	22	T547
10	D682	23	T569
11	D713	24	T692
12	D900	25	T752
13	D992	26	T178
14	D118	—	—

f				f (cont'd)
Contact Block(s)				Contact Block(s)
Standard				PenTUFF (Low Voltage)
Code	Description			Code	Description
	Contact Configuration	2-Position			Contact Configuration	2-Position

Blank	No Contacts	—	—	HXXX	1 N.O.	O	X
DXXX	1 N.O.	O	X	UXXX	1 N.C.	X	O
EXXX	1 N.C.	X	O	FXXX	1 N.O. - 1 N.C.	O	X
MXXX	2 N.O.	O	X			X	O
		O	X	FFXX	2 N.O. - 2 N.C.	O	X
NXXX	2 N.C.	X	O			X	O
		X	O			O	X
AXXX	1 N.O. - 1 N.C.	O	X			X	O
		X	O
AAXX	2 N.O. - 2 N.C.	O	X
		X	O
		O	X
		X	O
Note: X = Closed/O = Open.

⋆ Each standard and knob lever operator is factory assembled with a white insert. Other colors are available, factory assembled, if ordered in quantities of 10 or more.
‡ One insert of each color (blue, green, orange, red, and yellow).
§ Target tables are reversed from those shown.

3-Position Selector Switch Units, Non-Illuminated


Standard Knob Operator Cat. No. 800H-JP2KB7AXXX		Knob Lever Operator Cat. No. 800H-JP17KB7AXXX		Metal Wing Lever Operator Cat. No. 800H-JP11KB7AXXX

Contact Type	Operator Position			M = Maintained S = Spring Return	Standard Knob	Knob Lever	Metal Wing Lever
Contact Type				M = Maintained S = Spring Return	Cat. No.§	Cat. No.§	Cat. No.§
No Contacts	—	—	—	M M M	800H-JP2KB7	800H-JP17KB7	800H-JP11KB7
				S→M M	800H-JP4KB7	800H-JP18KB7	800H-JP15KB7
				M M←S	800H-JP5KB7	800H-JP19KB7	800H-JP16KB7
				S→M←S	800H-JP91KB7	800H-JP20KB7	800H-JP141KB7
	O X	O O	X O	M M M	800H-JP2KB7AXXX	800H-JP17KB7AXXX	800H-JP11KB7AXXX
				S→M M	800H-JP4KB7AXXX	800H-JP18KB7AXXX	800H-JP15KB7AXXX
1 N.O. - 1 N.C.				M M←S	800H-JP5KB7AXXX	800H-JP19KB7AXXX	800H-JP16KB7AXXX
1 N.O. - 1 N.C.				S→M←S	800H-JP91KB7AXXX	800H-JP20KB7AXXX	800H-JP141KB7AXXX
	O X O X	O O O O	X O X O	M M M	800H-JP2KB7AAXX	800H-JP17KB7AAXX	800H-JP11KB7AAXX
				S→M M	800H-JP4KB7AAXX	800H-JP18KB7AAXX	800H-JP15KB7AAXX
2 N.O. - 2 N.C.				M M←S	800H-JP5KB7AAXX	800H-JP19KB7AAXX	800H-JP16KB7AAXX
2 N.O. - 2 N.C.				S→M←S	800H-JP91KB7AAXX	800H-JP20KB7AAXX	800H-JP141KB7AAXX

Note:X = Closed/O = Open
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-JP4KB7.

3-Position Cylinder Lock Operator
Cat. No. 800H-JP42KB7AXXX

Contact Type	Operator Position			M = Maintained S = Spring Return	Cylinder Lock
					Key Removal Left	Key Removal Center	Key Removal All⋆
					Cat. No.§	Cat. No.§	Cat. No.§
No Contacts	O	X	X	M M M	800H-JP41KB7	800H-JP42KB7	800H-JP44KB7
				S→M⋆	—	800H-JP50KB7	800H-JP51KB7
				M←S	800H-HP5KL8DXXX	800H-JP38KB7	800H-JP73KB7
				M M	—	800H-JP631KB7	—
	O X	O O	X O	M M M⋆	800H-JP41KB7AXXX	800H-JP42KB7AXXX	800H-JP44KB7AXXX
				M←S	—	800H-JP50KB7AXXX	800H-JP51KB7AXXX
1 N.O. - 1 N.C.				M M←S	800H-JP69KB7AXXX	800H-JP38KB7AXXX	800H-JP73KB7AXXX
				S→M←S	—	800H-JP631KB7AXXX	—

Note:X = Closed/O = Open
⋆ Key removable in maintained positions only.
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-JP41KB7.

3-Position Selector Switch Units, Non-Illuminated

800

–

KB7

AAXX

(Knob/Wing Lever)

800

–

KB7

AAXX

c₁

d₁

(Cylinder Lock)

a		b		c
Barrel Type		Number of Positions		Knob Insert Colors⋆
Code	Description	Code	Description	Code	Color
H	Standard barrel length	JP	3-position	Blank	White knob insert or cylinder lock operator
HL	Long barrel			X	Packet of colored inserts‡
				Metal Wing Lever Colors
				Code	Color
				A	Red
				Blank	Grey

c₁		d
Cylinder Lock Operators		Knob/Lever Type Operators
Maintained Position		Standard Knob
Code	Locking Position	Code	Operator Function
41	Left	2	Maintained
42	Center	4	Spring return from left
43	Right	5	Spring return from right
44	All	91	Spring return from both
45	Left and center	Knob Lever
46	Right and left	Code	Operator Function
47	Right and center	17	Maintained
Spring Return from Left		18	Spring return from left
Code	Locking Position	19	Spring return from right
50	Center	20	Spring return from both
52	Right	Metal Wing Lever♣
51	Right and center	Code	Operator Function
Spring Return from Right		11	Maintained
Code	Locking Position	15	Spring return from left
69	Left	16	Spring return from right
38	Center	141	Spring return from both
73	Left and center
Spring Return from Both
Code	Locking Position
631	Center

d₁
Operator Type/Function§
Standard Knob
Code	Key No.
Blank	D018 (standard key)
Note: Refer to 2-Position Selector Switch Units, Non-Illuminated for additional key option codes.

e		f
Cam Option		Contact Block Option
Code	Description	Code	Description
KB7	Standard cam KB7	Blank	No contacts
KA1	Cam KA1	AXXX	2 contact targets for a given cam as shown in the W (white side) column of Table 5.
KA7	Cam KA7	AAXX	2 contact targets for a given cam as shown in the W (white side) column of Table 1 and 2 contact targets for the same cam as shown in the B (black side) column of Table 5. (1-800T-XA Contact Block per side. 2 Contact Blocks total.)
Note: For additional Cam descriptions, see Table 5.		AAAA	4 contact targets for a given cam as shown in the W (white side) column of Table 5 and 4 contact targets for the same cam as shown in the B (black side) column of Table 5. (2-800T-XA Contact Blocks per side. 4 Contact Blocks total.)

Table 5. Cam and Contact Block Functionality Table

Contact Block
Suffix Code

Circuits

Cam Codes

KB7
(Std.)

KA1

KA7

KC1

KC7

KD7

KE7

KQ1

KQ7

KR1

KR7

KT1

KT7

KU7

Note:X = Closed/O = Open

⋆ Each standard and knob lever operator is factory assembled with a white insert. Other colors available, factory assembled, if ordered in quantities of 10 or more.
‡ One insert of each color (blue, green, orange, red, and yellow).
§ For additional keys, see 2-Position Selector Switch Units, Non-Illuminated.
♣ Wing levers are not suitable with KE7 cam code.

4-Position Selector Switch Units, Non-Illuminated


Standard Knob Operator Cat. No. 800H-NP2KF4AAXX		Knob Lever Operator Cat. No. 800H-NP17KF4AAXX		Metal Wing Lever Operator Cat. No. 800H-NP11KF4AAXX

Contact Type	Operator Position				M = Maintained S = Spring Return	Standard Knob	Knob Lever	Metal Wing Lever
Contact Type					M = Maintained S = Spring Return	Cat. No.§	Cat. No.§	Cat. No.§
No Contacts	—	—	—	—	M M M M	800H-NP2KF4	800H-NP17KF4	800H-NP11KF4
					S→M M M	800H-NP3KF4	800H-NP29KF4	800H-NP13KF4
					M M M←S	800H-NP9KF4	800H-NP30KF4	800H-NP14KF4
	X O O O	O X O O	O O X O	O O O X	M M M M	800H-NP2KF4AAXX	800H-NP17KF4AAXX	800H-NP11KF4AAXX
					S→M M M	800H-NP3KF4AAXX	800H-NP29KF4AAXX	800H-NP13KF4AAXX
2 N.O. - 2 N.C.					M M M←S	800H-NP9KF4AAXX	800H-NP30KF4AAXX	800H-NP14KF4AAXX

Note:X = Closed/O = Open
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-NP3KF4.

Cylinder Lock Operator
Cat. No. 800H-NP32KF4AAXX

Contact Type	Operator Position				M = Maintained S = Spring Return	Cylinder Lock
						Key Removal Position 2	Key Removal Position 3	Key Removal All⋆
						Cat. No.§	Cat. No.§	Cat. No.§
No Contacts	—	—	—	—	M M M M	800H-NP32KF4	800H-NP33KF4	800H-NP61KF4
					S→M M M	800H-NP132KF4	800H-NP133KF4	800H-NP154KF4
					M M M←S	800H-NP232KF4	800H-NP233KF4	800H-NP251KF4
	X O O O	O X O O	O O X O	O O O X	M M M M	800H-NP32KF4AAXX	800H-NP33KF4AAXX	800H-NP61KF4AAXX
					S→M M M	800H-NP132KF4AAXX	800H-NP133KF4AAXX	800H-NP154KF4AAXX
2 N.O. - 2 N.C.					M M M←S	800H-NP232KF4AAXX	800H-NP233KF4AAXX	800H-NP251KF4AAXX

Note:X = Closed/O = Open
⋆ Key removable in maintained positions only.
§ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-NP32KF4.

4-Position Selector Switch Units, Non-Illuminated

800

–

KF4

AAXX

(Knob/Wing Lever)

800

–

KF4

AAXX

c₁

d₁

(Cylinder Lock)

a		b		c
Barrel Type		Number of Positions		Knob Insert Colors⋆
Code	Description	Code	Description	Code	Color
H	Standard barrel length	NP	4-position	Blank	White
HL	Long barrel			X	Packet of colored inserts‡
				Metal Wing Lever Colors
				Code	Color
				A	Red
				Blank	Grey

c1		d
Key Removal Position and Operator Function		Operator Function and Knob Type
Maintained		Standard Knob
Code	Operator Function	Code	Operator Function
31	Key removal position 1	2	Maintained
32	Key removal position 2	3	Spring return from position 1 to position 2
33	Key removal position 3	9	Spring return from position 4 to position 3
34	Key removal position 4	Knob Lever
61	Key removal all positions	Code	Operator Function
Spring Return From Position 1 to Position 2		17	Maintained
Code	Operator Function	29	Spring return from position 1 to position 2
132	Key removal position 2	30	Spring return from position 4 to position 3
133	Key removal position 3	Metal Wing Lever
134	Key removal position 4	Code	Operator Function
154	Key removal positions 2, 3, and 4	11	Maintained
Spring Return From Position 1 to Position 2		13	Spring return from position 1 to position 2
Code	Operator Function	14	Spring return from position 4 to position 3
231	Key removal position 1
232	Key removal position 2
233	Key removal position 3
251	Key removal positions 1, 2, and 3

d1		e		f
Optional Keys♣		Cam Option		Contact Block Option
D Series		Code	Description	Code	Description
Code	Description	KF4	F cam (standard)	Blank	No contacts
Blank	D018 (standard key)	KG4	G cam	AAXX	Two contact targets for a given cam as shown in the W (white side) column of Table 1 and 2 contact targets for the same cam as shown in the B (black side) column of Table 1. (One Cat. No. 800T-XA contact block per side. Two contact blocks total)
		KK4	K cam	AAAA	Four contact targets for a given cam as shown in the W (white side) column of Table 1 and 4 contact targets for the same cam as shown in the B (black side) column of Table 1. (Two Cat. No. 800T-XA contact blocks per side. Four contact blocks total.)
		KM4	M cam	PenTUFF (Low Voltage)
		KP4	P cam	FFXX	Two contact targets for a given cam as shown in the W (white side) column of Table 1 and 2 contact targets for the same cam as shown in the B (black side) column of Table 1. (One Cat. No. 800T-XAV contact block per side. Two contact blocks total)
		KH4	Overlapping cam	FFFF	Four contact targets for a given cam as shown in the W (white side) column of Table 1 and 4 contact targets for the same cam as shown in the B (black side) column of Table 1. (Two Cat. No. 800T-XAV contact blocks per side. Four contact blocks total.)

Table 1. Selector Switch Cam Targets

Contact Block
Suffix Code

Contact
Block
Side

Circuits

Cam Description

KF4

KG4

KK4∆

KM4∆

KP4

KN4§

↑
AAAA
FFFF
↓

↑
AAXX
FFXX
↓

White

Black

White

Black

Note:W = White B = Black. X = Closed/O = Open. For additional targets and overlapping cams, see Publication 800T-2.8.

⋆ Each standard and knob lever operator is factory assembled with a white insert. Other colors available, factory assembled, if ordered in quantities of 10 or more.

‡ One insert of each color (blue, green, orange, red, and yellow).

§ Overlapping cam.

♣ Devices supplied with 2 keys. Replacement part number for standard D018 key is X-181170

∆ Not available with wing lever operator.

Pilot Light Units


Transformer Type Pilot Light Cat. No. 800H-PP16M		Push-to-Test Pilot Light Cat. No. 800H-PPT16M		Pigtail Pilot Light Cat. No. 800H-LP24M

Type	Lamp Type	Supply Voltage	Lens Color⋆	Pilot Light	Push-to-Test	Pigtail
Type	Lamp Type	Supply Voltage	Lens Color⋆	Cat. No.‡	Cat. No.‡ §	Cat. No.‡ ♣
Operator only∆				800H-QPN00	800H-QPB00XX	—
Full voltage	Incandescent	24V AC/DC	Multi-color kit	800H-QP24M	800H-QPT24M	800H-LP24M
	Incandescent	120V AC/DC	Multi-color kit	800H-QP10M	800H-QPT10M	800H-LP10M
	No lamp	0…250V AC/DC	No lens	800H-QPN25	800H-QPTN25	800H-LPN25
	LED	24V AC/DC	Multi-color kit	—	—	800H-LPH24M
	LED	120V AC	Multi-color kit	—	—	800H-LPH10M
Universal	LED	12…130V AC/DC	Multi-color kit	800H-QPH2M	800H-QPTH2M	—
Transformer	Incandescent	120V AC, 50/60 Hz	Multi-color kit	800H-PP16M	800H-PPT16M	—
Transformer	LED	120V AC, 50/60 Hz	Multi-color kit	800H-PPH16M	800H-PPTH16M	—

⋆ Units ship with multi-color insert packet including amber, blue, green, red, and white.
‡ For long barrel versions, add an L to the cat. no. Example: Cat. No. 800HL-QPH2M
§ Includes one standard Cat. No. 800T-XA (1 N.O./1 N.C.) contact block.
♣ Pigtail length is 7 in.
∆ Operator only supplied without power module, lamp, lens cap, or contact blocks.

Pilot Light Units

800

–

a		b		c
Barrel Type		Power Module Type		Lamp Test Options
Code	Description	Code	Description	Code	Description
H	Standard barrel length	PP	Transformer (or dual input)	Blank	No test option
HL	Long barrel	QP	Full voltage/Universal	T	Push-to-test
		LP	Pigtail — Full voltage‡	D	Dual input — diode§
		LPK	Pigtail — full voltage‡ (for dual push buttons)	DT	Dual input — transformer relay§

d		e		e (cont'd)		f
Illumination Option		Voltage		Voltage		Lens Color
Code	Description	Transformer		Full Voltage — LED
Blank	Incandescent	Code	Description	2	12…130V AC/DC	Code	Color
H	LED∆	16	120V AC, 50/60 Hz	Dual Input		Blank	No lens with no contacts
		26	240V AC, 50/60 Hz	16	120V AC	M	Multi-color⋆
		46	480V AC, 50/60 Hz	24	24V AC/DC∇
		56	600V AC, 50/60 Hz	Pigtail
		Full Voltage — Incandescent		24	24V AC/DC
		24	24V AC/DC	10	120V AC/DC
		10	120V AC/DC	20	240V AC/DC
		20	240V AC/DC

Note: Push-to-test pilot light is supplied with a factory jumpered Cat. No. 800T-XA, 1 N.O/1 N.C contact block.
⋆ Multi-color insert packet includes amber, blue, green, red, and white
‡ Lamp test options is not available with pigtail.
§ Only available with power module type code PP.
∆ LED illumination option is not available with diode type dual input lamp test options.
∇ Dual input diode only.