Hazardous Location

Catalogs > Industrial Controls Catalog > Push Buttons > Hazardous Location > Bulletin 800H Type 7&9 Hazardous Location Push Buttons

Bulletin 800H Type 7&9 Hazardous Location Push Buttons

Introduction Standards Compliance and Certifications Product Selection Product Selection for Stations
Modifications and Accessories Pilot Light Wiring Diagrams Specifications Approximate Dimensions
Modifications and Accessories

Contact Blocks∆ 

Packaged in kit form for field installation. All necessary mounting hardware is provided with each contact block kit. Contact ratings are listed on Specifications⋆ .

Note:It is not recommended to mount more than four contact blocks on any one unit (maximum two blocks deep). Sealed switch contact blocks are limited to two blocks per unit maximum.

Click to enlarge - 800T_800H-1_30-1   Click to enlarge - 800T_800H-1_30-7   Click to enlarge - 800T_800H-1_30-2
Shallow Block Mini Block PenTUFF (Low Voltage) Contact Block

Contact Type Shallow Block⋆ ‡ §  Mini Block⋆ §  PenTUFF (Low Voltage) Block⋆ ‡ § 
Cat. No. Cat. No. Cat. No.
1 N.O. 800T-XD1 800T-XD5 800T-XD1V
1 N.C. 800T-XD2 800T-XD6 800T-XD2V
1 N.O.E.M. 800T-XD3 — 800T-XD3V
1 N.C.L.B. 800T-XD4 — 800T-XD4V
1 N.O. - N.C. 800T-XA — 800T-XAV
2 N.O. 800T-XA2 — —
2 N.C. 800T-XA4 — —
1 N.C.L.B. - 1 N.O. 800T-XA1 — —
1 N.C.L.B. - 1 N.C. 800T-XA7 — —
  
⋆ To determine if a conduit seal-off is necessary, see Miscellaneous for sealing well information.
‡ Specify Bulletin 800TC for finger-safe contact blocks. Example: Cat. No. 800TC-XA.
§ Contact blocks with normally closed contacts meet direct drive positive opening standard requirements.

Click to enlarge - 800T_800H-1_30-3   Click to enlarge - 800T_800H-1_30-4   Click to enlarge - 800T_800H-1_30-5
Logic Reed Block Sealed Switch Block Stackable Sealed Switch Block

Contact Type Logic Reed Block♣  Sealed Switch Block♣  Stackable Sealed Switch Block♣ 
Cat. No. Cat. No. Cat. No.
1 N.O. 800T-XD1R 800T-XD1P 800T-XD1Y
1 N.C. 800T-XD2R 800T-XD2P 800T-XD2Y
1 N.O. - 1 N.C. 800T-XAR 800T-XAP 800T-XAY
2 N.O. 800T-XA2R — 800T-XA2Y
2 N.C. 800T-XA4R — 800T-XA4Y
  
♣ To determine if a conduit seal-off is necessary, see Miscellaneous for sealing well information.
∆ Refer to 800T/H section, Contact Blocks, for additional contact blocks and accessories.

Replacement Color Caps (Illuminated)

Click to enlarge - 800H-2_27a-1   Click to enlarge - 800H-2_27a-2   Click to enlarge - 800H-2_27a-3   Click to enlarge - 800H-2_27a-4
Pilot Light
Cat. No. 800H-N104M 		Push-to-Test Pilot Light
Cat. No. 800H-N105M 		Illuminated Push Button
Cat. No. 800H-N106M 		Illuminated Push-Pull
Cat. No. 800H-NP50M

Color Pilot Light Push-to-Test Pilot Light Illuminated Push Button Illuminated Push-Pull
Cat. No. Cat. No. Cat. No. Cat. No.
Multi-color kit 800H-N104M 800H-N105M 800H-N106M 800H-NP50M
  

Replacement Color Caps (Non-Illuminated)

Click to enlarge - 800H-2_27a-5   Click to enlarge - 800H-2_27a-6   Click to enlarge - 800H-2_27a-7   Click to enlarge - 800H-2_27a-8
Momentary Mushroom —Standard (Plastic)
Cat. No. 800T-N246R 		Momentary Mushroom —Jumbo (Metal)
Cat. No. 800T-N248R 		Push-Pull — Standard (Metal)
Cat. No. 800H-NP51C 		Push-Pull — Jumbo (Metal)
Cat. No. 800H-NP52A

Color Momentary Mushroom —
Standard (Plastic) 		Momentary Mushroom —
Jumbo (Metal) ⋆  		Push-Pull
Standard (Metal) 		Push-Pull Jumbo
(Metal)
Cat. No. Cat. No. Cat. No. Cat. No.
Red 800T-N246R 800T-N248R 800H-NP51A 800H-NP52A
Green 800T-N246G 800T-N248G 800H-NP51B 800H-NP52B
Blue 800T-N246BL 800T-N248BL 800H-NP51C 800H-NP52C
Yellow 800T-N246Y 800T-N248Y 800H-NP51E 800H-NP52E
Black 800T-N246B 800T-N248B 800H-NP51H 800H-NP52H
Grey 800T-N246GR 800T-N248GR 800H-NP51G —
Natural — 800T-N248 — —
  
⋆ To order plastic jumbo mushroom caps, replace 248 with 247. Plastic not available in natural color.
Example: Cat. No. 800T-N248R becomes Cat. No. 800T-N247R.

Replacement Knobs and Dual Push Button Assembly

Click to enlarge - 800H-2_27a-9   Click to enlarge - 800H-2_27a-10   Click to enlarge - 800H-2_27a-11   Click to enlarge - 800H-2_27a-12
Standard Knob
Cat. No. 800H-N130F 		Knob Lever
Cat. No. 800H-131F 		Wing Lever
Cat. No. 800H-N138 		Dual Push Button
Cat. No. 800H-NP39

Color Standard Knob Knob Lever Wing Lever‡  Dual Push Button
Cat. No. Cat. No. Cat. No. Cat. No.
White 800H-N130F 800H-N131F — —
Kit (Complete)§  800H-N130 800H-N131 — —
Grey — — 800H-N138 —
Red — — 800H-N138A —
Green Red — — — 800H-NP39
  
‡ Standard finish is grey.
§ Kit includes knob and packet of inserts (Cat. No. 800T-N123). Refer to color insert kits on Miscellaneous.

Boots—Non-Illuminated Momentary Contact Push Buttons Units

Note:For Bul. 800H/HL Type 7&9 operators, order one adapter and one boot per operator.


Adapters

Push Button Type Cat. No.
Flush head 800H-NPAF
Extended head 800H-NPAE
  

Boots

Boots supplied with control stations and components are made of a chlorosulfonated polyethylene material with stainless steel insert ring. To order boots with silicone, urethane, or ethylene propylene material, see the table below. Material application information shown below.

Click to enlarge - 800T_800H-1_32-12
Cat. No. 800H-N5A


Insert Material Boot Color Material
Chlorosulfonated Polyethylene§  Silicone Ÿ§  Urethane ŸŸ§  Ethylene Ÿ
Propylene ŸŸ§ 
Cat. No. Cat. No. Cat. No. Cat. No.
Stainless steel♣  Red 800H-N5A 800H-N101R 800H-N100R 800H-N103R
Green 800H-N5B 800H-N101G 800H-N100G 800H-N103G
Black 800H-N5H 800H-N101B 800H-N100B 800H-N103B
Yellow 800H-N5E 800H-N101Y 800H-N100Y —
Blue 800H-N5C 800H-N101BL 800H-N100BL —
  
‡ May be added to flush or extended head push button units to protect against foreign materials reaching the opening between the button and the locking ring.
♣ Series B boots incorporate a stainless steel insert as standard.
§ Dots printed on the inside of the boot identify the boot material.

Booted Knobs

Click to enlarge - 800H-2_28a-3   Click to enlarge - 800H-2_28a-4
Booted Standard Knob Selector Switch
Cat. No. 800H-NP5 		Booted Knob Lever Selector Switch
Cat. No. 800H-NPE5

Switch Type Boot Material⋆ 
Chlorosulfonated Polyethylene Silicone Ÿ Urethane ŸŸ Ethylene Ÿ
Propylene ŸŸ
Cat. No. Cat. No. Cat. No. Cat. No.
Standard Knob Selector Switch‡  800H-NP5 800H-NP101 800H-NP100 800H-NP103
Knob Lever Selector Switch‡  800H-NPE5 800H-NPE101 800H-NPE100 800H-NPE103
  
⋆ Dots printed on the inside of the boot identify the boot material.
‡ Includes color insert kit.

Push Button Guards and Mushroom Push Button Guards

Click to enlarge - 800H-2_28a-5   Click to enlarge - 800H-2_28a-6   Click to enlarge - 800H-2_28a-7   Click to enlarge - 800H-2_28a-8
Cat. No. 800H-NP19 Cat. No. 800H-NP13 Cat. No. 800H-NP9 Cat. No. 800H-NP12

Push Buttons, Pilot Lights and
Push-to-Test 		Extra Long Guard (1 in.)
for Push Button 		Mushroom Jumbo Mushroom
Cat. No. Cat. No. Cat. No. Cat. No.
800H-NP19 800H-NP13 800H-NP9 800H-NP12
  

Protective Rings

Click to enlarge - 800H-2_28a-9   Click to enlarge - 800H-2_28a-10
Protective Ring for 2-Position Push-Pull
Cat. No. 800H-NP40 		Jumbo Protective Ring for 2-Position Push-Pull
Cat. No. 800H-NP40J

Protective Ring for Push-Pull Devices
Description Type Cat. No.
Protective ring for Bul. 800H 2-position non-illuminated push-pull operators. Often used to avoid unintentional tripping of E-stop operators. Available for standard size button (40 mm) or for jumbo button (60 mm). For standard size button 800H-NP40
For jumbo size button 800H-NP40J
  

General Accessories

Plugs

  Description Cat. No.
Click to enlarge - 800H-2_29a-1 Coupler
Used for both horizontal and vertical assembly. 		800H-NP7
Cat. No. 800H-NP7
  Description Type Cat. No.
Click to enlarge - 800H-2_29a-2 Closing Plug
Whenever an enclosure with more than the required number of openings is used, this plug can be used to close the unused openings. Includes synthetic O-ring washer. 		For Cover Hole 800H-NP1
Cat. No. 800H-NP1
(Operators not included) 		For Base Coupler Hole 800H-NP3
  Description Size Cat. No.
Click to enlarge - 800H-2_29a-3 Conduit Entry Plug
This plug can be used to plug unused conduit openings in Type 7 and 9 bases. 		3/4 in. 800H-NP10
Cat. No. 800H-NP10
(Operators not included) 		1 in. 800H-NP11
  

Locking Attachments

  Description Cat. No.
Click to enlarge - 800H-2_29a-4 Push Button Padlocking Attachments
This device permits locking in the depressed position on extended head push button units only. 		800H-NP2
Cat. No. 800H-NP2
(Padlock not included)
Click to enlarge - 800H-2_29a-5 Dual Push Button Extended Head Padlocking Attachments
This device permits locking for dual push button — extended head units only. 		800H-NP17
Cat. No. 800H-NP17
(Padlock not included)
  

Locking Attachments

  Description Cat. No.
Click to enlarge - 800H-2_30a-1 Padlocking Cover
Padlocking cover is used for Type 7 and 9 selector switches, non-illuminated push buttons (except mushrooms) and non-illuminated 2-position push-pull units, but not for potentiometer units.
Note:Push-pull units will only lock in the depressed position. Padlocking cover includes blank legend plate for customer marking. A pre-marked legend plate entitled OPEN COVER TO OPERATE (front view) and PULL-TO-START-PUSH-TO-STOP (rear view) is available. To order legend plate only, specify Cat. No. 800H-W174L. 		800H-NP4
Cat. No. 800H‑NP4
(Padlock not included)
  

Miscellaneous

    Description Style No. of Wires Cat. No.
Click to enlarge - 800H-2_30a-2 Click to enlarge - 800H-2_30a-3 Sealing Well with or without Integral Type 3 Flange Seal
These sealing wells can only be used with bases having 1 in. conduit entries. They reduce costs usually necessary with other conduit seal fittings for most installations (subject to applicable codes and laws) while maintaining Type 7 and 9 integrity. When using a sealing well with integral flange seal for Type 3 outdoor applications, an approved drain fitting must be provided. (Refer to National Electrical Code.) 		With Integral Flange Seal, Type 3, 7, and 9 2 800H-NPRD90
4 800H-NPRD91
6 800H-NPRD92
8 800H-NPRD93
Without Integral Flange Seal, Type 7 and 9 2 800H-NPD90
4 800H-NPD91
Cat. No. 800H‑NPRD91 Cat. No. 800H‑NPD93 6 800H-NPD92
8 800H-NPD93
  Description Style Cat. No.
Click to enlarge - 800H-2_30a-4 Type 3 Flange Seal
This seal provides a Type 3 rating while maintaining Type 7 and 9 integrity. An approved drain (see listing) is required for condensation when using this option (refer to National Electrical Code). For a Type 4 rating, use sealing nuts to seal the push button operators in addition to using the flange seal. Sealing kit is comprised of flange seal and sealing nut. They are used with the Allen-Bradley enclosures listed on Complete Assembled Stations (Supplied with 3/4 in. Dead End Conduit Entry — Cat. No. 800H‑1HZX7) for outdoor applications. 		Flange Seal 800H-NP20
Drain for 3/4 in. Conduit Opening 800H-NP21
Cat. No. 800H-NP20 Drain for 1 in. Conduit Opening 800H-NP22
Click to enlarge - 800H-2_30a-5 Type 4 Sealing Nut 800H-N479
Cat. No. 800H-NP21 Type 4 Sealing Kit 800H-N479F
  Description Color Cat. No.
Click to enlarge - 800H-2_30a-6 Color Insert Kit
These color insert kits are used with illuminated push buttons, pilot lights, push-pull, and push-to-test push buttons (order quantity of 1 to receive kit of 5 inserts). 		Red 800H-NP23R
Green 800H-NP23G
Amber 800H-NP23A
Blue 800H-NP23B
White 800H-NP23W
Cat. No. 800H-NP23R One of each color 800H-NP23
  

Replacement Lamps

Pilot Lights, Illuminated Push Buttons, Illuminated Push-Pull, Illuminated Push-Pull/Twist to Release, and Illuminated Selector Switches

Lamp Type Current, Typical Lamp Voltage ANSI No. Catalog Voltage Code Cat. No.
Incandescent Full Voltage
Transformer 		150 mA/250 mA 6.3V AC 755/1866 6, 16, 26, 36, 46, 56, 76 ⋆  800T-N65
Click to enlarge - 800T_800H-1_40-1 Full Voltage 80 mA 14V AC/DC 756 12 ⋆  800T-N141
70 mA 24V AC/DC 757 24 ⋆  800T-N157
50 mA 48V AC/DC 1835 48 ⋆  800T-N365
Full Voltage
Resistor 		22 mA 120V AC/DC 949 10, 11 ⋆  800T-N169
Flashing 150 mA 6V AC/DC 267 6 ⋆  800T-N212
Dual Input Diode 57 mA 24V AC/DC 24 MB 24 ⋆  800T-N180
21 mA 120V AC 90 MB 16 ⋆  800T-N261
Neon — 2 mA 120V AC/DC B2A 10, 20 609-N9
Click to enlarge - 800T_800H-1_40-2
Lamp Type Current, Typical‡  Lamp Voltage Leakage Current Code Cat. No.‡ 
LED§  Universal 13 mA @ 24V DC
8.5 mA @ 120V AC§  		3V♣  3 mA 2 800T-N376x
Click to enlarge - 800T_800H-1_40-2 Transformer 60 6V 14 mA 16, 26, 46, 56 800T-N377x
  
⋆ Item is sold in multiples of 5. Order quantity of 5 to receive package of 5 pieces.
‡ To complete the cat. no. replace the x with the first letter of the desired color: Green, Red, or White.
§ Typical current consumption values indicated are relative to the input of the power module.
♣ Lamp is intended for use with power module Cat. No. 800TC-N374 which has an input voltage rating of 12 …130V AC/DC.

Legacy LED Lamps∆ 

Lamp Type Current, Typical♦  Lamp Voltage Leakage Current Catalog Voltage Code Cat. No.♠ 
LED&  Full Voltage 13 mA/22 mA 12V AC/DC 3 mA 12 800T-N362x
20 mA/21 mA 24V AC/DC 3 mA 24 800T-N319x
Click to enlarge - 800T_800H-1_40-2 12 mA/17 mA 32V AC/DC 3 mA 32 800T-N363x
9 mA/14 mA 48V AC/DC 3 mA 48 800T-N364x
3.3 mA/6 mA 120V AC — 10 800T-N320x
4.5 mA/6.2 mA 130V AC/DC 3 mA 13 800T-N321x
Full voltage 50 mA 6V AC 14 mA 6, 16, 26, 36, 46, 56, 76 800T-N318x
Flashing 18 mA 24V AC/DC — N/A ∇  800T-N319Fx
  
∆ In full voltage applications, these lamps are intended to be used with power module Cat. No. 800T-N330.
& All LEDs except 120V have an internal shunt resistor for use with solid-state outputs. LEDs will not illuminate below listed leakage current.
♦ Typical current draw varies with LED color. The first mA value is for a green or blue LED and the second mA value is for a red or amber LED.
♠ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green, Red, Blue, or White. White LEDs only available in 6V, 24V, 120V, and 130V.
∇ Flashing rate is 2 Hz.

Legend Plates

Click to enlarge - 800H-2_31a-1   Click to enlarge - 800H-2_31a-2   Click to enlarge - 800H-2_31a-3   Click to enlarge - 800H-2_31a-4

Blank Legend Plates

Legend Plate Color Lever Style Standard Size Jumbo Size Special Jumbo Size
Use 1 lever style legend
with each lever
type cover
(Cat. Nos. 800H-NP14,
-NP15, -NP16 or -NP34) 		Use 2 standard size
legends with each
standard 2 hole cover
(Cat. No. 800H-NP31) 		Use 1 jumbo size
legend with each
standard 1 hole cover
(Cat. No. 800H-NP30) 		Use 1 special jumbo legend with
each special 2 hole cover
(Cat. No. 800H-NP33)
Ex: Dual Push Button/
Pigtail Pilot Light
Cat. No. Cat. No. Cat. No. Cat. No.
Grey — 800H-Y59 800H-Y59J 800H-Y141J
Red — 800H-Y121 800H-Y121J —
Green — 800H-Y136 800H-Y136J —
Yellow — 800H-Y700 800H-Y700J —
Top Grey — Bottom Grey 800H-Y222 — — —
Top Grey — Bottom Red 800H-Y223 — — —
Left Green — Right Red — — — 800H-Y140J
Grey with Potentiometer Graduations — 800H-Y109 800H-Y109J —
  

Custom Legend Plates

Legend Plate Color Lever Style Standard Size Jumbo Size Special Jumbo Size
Use 1 lever style legend
with each lever
type cover
(Cat. Nos. 800H-NP14,
-NP15, -NP16 or -NP34) 		Use 2 standard size
legends with each
standard 2 hole cover
(Cat. No. 800H-NP31) 		Use 1 jumbo size
legend with each
standard 1 hole cover
(Cat. No. 800H-NP30) 		Use 1 special jumbo legend with
each special 2 hole cover
(Cat. No. 800H-NP33)
Ex: Dual Push Button/
Pigtail Pilot Light
Cat. No. Cat. No. Cat. No. Cat. No.
Grey — ⋆  800H-Y59E ⋆  800H-Y59JE ⋆  800H-Y141JE
Red — ⋆  800H-Y121E ⋆  800H-Y121JE —
Green — ⋆  800H-Y136E ⋆  800H-Y136JE —
Yellow — 800H-Y700E 800H-Y700JE —
Top Grey — Bottom Grey ⋆  800H-Y222E — — —
Top Grey — Bottom Red ⋆  800H-Y223E — — —
Left Green — Right Red — — — ⋆  800H-Y140JE
Grey with Potentiometer Graduations — ⋆  800H-Y109E ⋆  800H-Y109JE —
  
⋆ Horizontally mounted engraved legend plates (with standard or custom marking) are available. Add the letter H after the Y in the cat. no.
Example: Cat. No. 800H-Y222E becomes 800H-YH222E.

Lever Style Legend Plates with Standard Markings

Click to enlarge - 800H-2_31a-5


Legend Marking Cat. No. Legend Marking Cat. No.
Upper/Lower Upper/Lower
HAND
AUTO 		800H-Y228 OPEN
CLOSE 		800H-Y205
JOG
RUN 		800H-Y227 RUN
STOP (Red) 		800H-Y226
JOG
STOP (Red) 		800H-Y206 START
STOP (Red) 		800H-Y200
ON
OFF 		800H-Y225 — —
  

Legend Plates, Continued

Legend Plates with Standard Markings

Click to enlarge - 800H-2_31a-2   Click to enlarge - 800H-2_31a-3

Legend Marking Standard Size Jumbo Size Legend Marking Standard Size Jumbo Size
Cat. No. Cat. No. Cat. No. Cat. No.
AUTO-OFF-HAND 800H-Y1 800H-Y1J ON 800H-Y30 800H-Y30J
AUTO-MAN-HAND 800H-Y125 800H-Y125J OPEN 800H-Y31 800H-Y31J
CLOSE 800H-Y2 800H-Y2J OPEN-CLOSE 800H-Y32 800H-Y32J
CYCLE START 800H-Y62 800H-Y62J OPEN-OFF-CLOSE 800H-Y33 800H-Y33J
DOWN 800H-Y3 800H-Y3J OUT 800H-Y34 —
EMERG. STOP (Red) 800H-Y4 800H-Y4J PUSH TO STOP-PULL TO START 800H-Y118 800H-Y118J
FAST 800H-Y5 800H-Y5J POWER ON 800H-Y139 800H-Y139J
FEED START 800H-Y66 800H-Y66J RAISE 800H-Y35 800H-Y35J
FEED STOP 800H-Y67 800H-Y67J RAISE-LOWER 800H-Y36 800H-Y36J
FOR.-REV. 800H-Y6 800H-Y6J RAISE-OFF-LOWER 800H-Y37 800H-Y37J
FOR.-OFF-REV. 800H-Y7 800H-Y7J RESET 800H-Y38 800H-Y38J
FORWARD 800H-Y8 800H-Y8J REVERSE 800H-Y39 800H-Y39J
FOURTH SPEED 800H-Y124 800H-Y124J RUN 800H-Y40 800H-Y40J
FULL SPEED 800H-Y9 800H-Y9J RUN-INCH 800H-Y134 800H-Y134J
HAND-AUTO 800H-Y10 800H-Y10J RUN-JOG 800H-Y41 800H-Y41J
HAND-OFF-AUTO 800H-Y11 800H-Y11J SAFE-RUN 800H-Y42 800H-Y42J
HIGH 800H-Y12 800H-Y12J SECOND SPEED 800H-Y43 800H-Y43J
HIGH-LOW 800H-Y13 800H-Y13J SLOW 800H-Y44 800H-Y44J
HIGH-OFF-LOW 800H-Y14 800H-Y14J SLOW-FAST 800H-Y45 800H-Y45J
IN 800H-Y15 800H-Y15J SLOW-OFF-FAST 800H-Y46 800H-Y46J
INCH 800H-Y16 800H-Y16J SPEED⋆  800H-Y108 800H-Y108J
JOG 800H-Y17 800H-Y17J START (Green) 800H-Y47 800H-Y47J
JOG FORWARD 800H-Y18 800H-Y18J START-JOG 800H-Y48 800H-Y48J
JOG REVERSE 800H-Y19 800H-Y19J START-STOP 800H-Y49 800H-Y49J
JOG-RUN 800H-Y20 800H-Y20J STOP (Red) 800H-Y50 800H-Y50J
JOG-SAFE-RUN 800H-Y22 800H-Y22J STOP-START 800H-Y51 800H-Y51J
JOG-STOP-RUN 800H-Y21 800H-Y21J SUMMER-OFF-WINTER 800H-Y53 800H-Y53J
LEFT-RIGHT 800H-Y23 800H-Y23J SUMMER-WINTER 800H-Y52 800H-Y52J
LOW 800H-Y24 800H-Y24J TEST 800H-Y54 800H-Y54J
LOW SPEED 800H-Y25 — THIRD SPEED 800H-Y55 —
LOWER 800H-Y26 800H-Y26J UP 800H-Y56 800H-Y56J
OFF 800H-Y27 800H-Y27J UP-DOWN 800H-Y57 800H-Y57J
OFF-COOLANT-ON 800H-Y28 800H-Y28J UP-OFF-DOWN 800H-Y58 800H-Y58J
OFF-ON 800H-Y29 800H-Y29J — — —
  
⋆ Graduated potentiometer type.