Catalogs > Industrial Controls Catalog > Push Buttons > Touch/Palm > Bulletin 800P Palm-Operated Push Buttons
Bulletin 800P Palm-Operated Push Buttons
| Introduction |  |
Standards Compliance and Certifications | |
Product Selection | |
Accessories | |
Specifications | |
Approximate Dimensions | |
| Description | Button Color | Cat. No. | Cat. No. | ||
| Standard | Anti-Slip | ||||
|
|
Button Covers Button covers are used to reduce possible slipping due to fluids on the operator. |
Red | 800P-NCR | 800P-NCR1 |
| Black | 800P-NCB | 800P-NCB1 | |||
| Green | 800P-NCG | 800P-NCG1 | |||
| Standard Button Cover Cat. No. 800P‑NCB |
Anti-Slip Button Cover Cat. No. 800P‑NCG1 |
Yellow | 800P-NCY | 800P-NCY1 | |
| Description | Style | Color | Cat. No. | ||
|
|
Guards These guards prevent accidental activation of the button and protect it from damage. Note:Guards are required in most two hand safety applications (See OSHA and ANSI standards). |
Side | Yellow | 800P-NBG1 |
| Die Cast | Grey | 800P-NBG | |||
| Side Guard Cat. No. 800P‑NBG1 |
Die Cast Guard Cat. No. 800P‑NBG |
Die Cast | Yellow | 800P-NBGY | |
| Description | Style | Cat. No. | |||
|
|
Bases The conduit hub(s) on these replacement mounting bases come with a 3/4 in. opening. |
Single Hub | 800P-B1 | |
| Single Hub Base Cat. No. 800P‑B1 |
Double Hub Base Cat No. 800P‑B2 |
Double Hub | 800P-B2 | ||
| Description | Enclosure | Cat. No. | |||
|
|
Adaptors These adaptor flanges are used between the operator and the mounting base, when using a non-Allen-Bradley base. |
Standard⋆ | 800P-N150 | |
| Standard Adapter Cat. No. 800P‑N150 |
FS Adaptor Cat. No. 800P‑N4 |
FS | 800P-N4 | ||
| Description | Marking | Cat. No. | |||
|
Legend Plates These legend plates can be mounted on the cover. |
Blank (Grey) | 800P-X107‡ | ||
| Blank (Red) | 800P-X129‡ | ||||
| START | 800P-X130 | ||||
| STOP | 800P-X131 | ||||
| INCH | 800P-X132 | ||||
| RUN | 800P-X133 | ||||
| RUN INCH |
800P-X134 | ||||
| Legend Plates | TOP STOP |
800P-X135 | |||
| ⋆ Horizontal mounting holes are 2-3/8 in. (60.3 mm) center-to-center. Vertical mounting holes are 4-1/2 in. (114.3 mm) center-to-center. | |||||
| ‡ To order with custom engraved text, add suffix E and supply text. One or two lines of text with maximum of 5 characters per line. | |||||
Contact Blocks
Packaged in a kit form for field installation. All necessary mounting hardware is provided with each contact block kit. Contact ratings are listed on Standard Contact Ratings.
Note:It is recommended to mount no more than four contact blocks on any one unit (maximum two blocks deep).
|
|
|
|
| Contact Type | Shallow Block‡ | PenTUFF Block‡ | Logic Reed Block§ |
| Cat. No. | Cat. No. | Cat. No. | |
| 1 N.O. | 800T-XD1 | 800T-XD1V | 800T-XD1R |
| 1 N.C. | 800T-XD2 | 800T-XD2V | 800T-XD2R |
| 1 N.O. - N.C. | 800T-XA | 800T-XAV | 800T-XAR |
| Note:Contact blocks with normally closed contacts meet direct drive positive opening standard requirements. | |||
| § Logic Reed blocks can be physically mounted on a Bul. 800P operator, but this combination is not UL Listed for Class 1 Div 2 hazardous applications. | |||
| ‡ For contact ratings, see Standard Contact Ratings. | |||