Bulletin 600 Single Phase
|
Bulletin 600
Starting and overload protection of small 1-phase AC/DC motors used on the following:
- Unit heaters
- Fans
- Stokers
- Pumps
- Refrigeration compressors
Bulletin 600 manual switches consist of a snap switch combined with a thermal overload device operating on the solder-ratchet principle. The switch is designed to prevent being held closed under a sustained motor overload. To reset the overload mechanism, the switch lever is moved to the OFF position. The motor can be restarted by pushing the switch lever to the ON position. Applications include compressors, fans and pumps.
| Table of Contents |
| Accessories |
| Modifications |
| Approximate Dimensions |
Standards Compliance and Certifications
Standards Compliance
- UL 508
- EN60947-4-1
- CSA C22.2, No. 14
Certifications
- UL Listed — Enclosed Products (File No. E14841; Guide No. NLRV)
- UL Recognized — Open Style Products (File No. E14841; Guide No. NLRV2)
- CSA Certified (File No. LR 1234)
- American Bureau of Shipping (ABS)
- CE Marked
- Hazardous Location:
UL Listed (File No. E10314)
CSA Certified (File No. LR 11924)
Product Seletion
Your order must include: 1) Cat. no. of the switch, 2) Cat. no. of the heater element(s), and 3) if required, cat. no. of any accessories.
Ratings
Single Pole — 1 HP 115…230V AC, 1 HP 277V AC, Open Type without Enclosure or Type 1 General Purpose Enclosure
Two Pole — 1 HP 115…230V AC, 1 HP 277V AC, Open Type without Enclosure or Type 1 General Purpose Enclosure, 3/4 HP 115…230V DC
Selector Switch — 1 HP 115…230V AC, 1 HP 277V AC, Open Type without Enclosure or Type 1 General Purpose Enclosure
Heater Element — See Eutectic Alloy Overload Relay Heater Elements for heater element selection table.
| Description | Open Type Without Enclosure Includes Legend Plate |
Type 1 General Purpose Enclosure Surface Mounting |
Type 1 General Purpose Enclosure Flush Mounting Includes Flush Plate but not Switch Box |
Type 4 Watertight Enclosure |
Type 7 & 9 Enclosure Class I, Groups C & D Class II, Groups E, F & G – Divisions 1 & 2 – Hazardous Locations |
|
| Stainless Steel Flush Plate |
||||||
| Cat. No. | Cat. No. | Cat. No. | Cat. No. | Cat. No. | ||
| Switch Only | ||||||
| Toggle Type | 1-Pole | 600-TOX4 | 600-TAX4 | 600-TQX4 | — | — |
| 2-Pole | 600-TOX5 | 600-TAX5 | 600-TQX5 | 600-TCX5 | 600-TEX5 | |
| Key Type | 2-Pole | 600-TOX49 | 600-TAX49 | 600-TQX49 | — | — |
| Lever Type | 1-Pole | 600-TOX149 | 600-TAX149 | — | — | — |
| Switch with Neon Pilot Light (115 or 230V) | ||||||
| Toggle Type | 1-Pole | 600-TOX216 | 600-TAX216 | 600-TQX216 | — | — |
| 2-Pole | 600-TOX109 | 600-TAX109 | 600-TQX109 | |||
| Key Type | 2-Pole | 600-TOX110 | 600-TAX110 | 600-TQX110 | ||
| Switch with Incandescent Pilot Light | ||||||
| Toggle Type | 2-Pole 115V | — | — | — | 600-TCD7 | 600-TED7 |
| 2-Pole 230V | 600-TCA7 | 600-TEA7 | ||||
| Switch and “Hand-Off-Auto” Selector Switch (for use on AC only) | ||||||
| Toggle Type | 2-Pole | — | 600-TAX9 | 600-TQX9 | 600-TCX9 | 600-TEX9 |
| Switch with Neon Pilot Light and “Hand-Off-Auto” Selector Switch (115 or 230V, AC only) | ||||||
| Toggle Type | 2-Pole | — | 600-TAX142 | 600-TQX142 | — | — |
| Key Type | 2-Pole | — | 600-TAX145 | — | — | — |
| Two Switch Units in One Enclosure | ||||||
| Toggle Type | 2-Pole | — | 600-TAX10 | — | 600-TCX10 | 600-TEX10 |
| Two Switch Units in One Enclosure Neon Pilot Light on Both Units (115 or 230V) | ||||||
| Toggle Type | 2-Pole | — | 600-TAX144 | 600-TQX144 | — | — |
| Two Speed Switch | ||||||
| Toggle Type | 2-Pole | — | 600-TAX298 | — | — | — |
| Two Speed Switch with Neon Pilot Lights (115 or 230V) | ||||||
| Toggle Type | 2-Pole | — | 600-TAX293 | 600-TQX293 | — | — |
| Separate Cover and Switch Assembly¬ | ||||||
| Toggle Type | 2-Pole | — | — | — | — | 600-N12 |
| Hand-Off-Auto | 600-N14 | |||||
| ¬ For use with Bulletin 800H, Type 7 and 9, Series C or later bases. | ||||||
Accessories
| Description | NEMA Enclosure Type |
Cat. No. |
| Pilot Light Replacement Bulb Incandescent¬ (Mfg. Designation #120 PSB-120V) Note: Pilot lights as used on Bulletin 600 switches indicate whether the motor is running only if the switch is used to control the motor directly. If a thermostat, pressure switch, or some other pilot device controls the operation of the motor, the pilot light on the Bulletin 600 switch merely indicates whether the power is ON or OFF. |
4, 7, and 9 | 800S-N60 |
|
||
| Locking Attachment (For Toggle Operated Only) |
1 (Switches in the Type 4 and Type 7 and 9 enclosures are supplied as standard with provisions for locking in the OFF or ON position.) |
600-N1 |
|
||
| Drain (For 3/4 in. (19 mm) Conduit Opening) |
7 and 9 | 800H-NP21 |
|
||
| Flange Seal (Provides NEMA Type 3 rating for outdoor locations in addition to maintaining NEMA Type 7 and 9 integrity) Note: An approved drain Cat. No. 800H-NP21 is required for condensation when this option is used (refer to local Electrical Code). |
3, 7, and 9 | 800H-NP20 |
|
||
| Sealing Well (See applicable codes and laws) (Not available for use with Cat. No. 600-TEX5) Note: When using a sealing well with integral flange seal for NEMA Type 3 outdoor applications, an approved drain fitting must be provided (refer to local Electrical Code). |
3, 7, and 9 (With integral flange seal) |
2 wire: 800H-NPRD90 4 wire: 800H-NPRD91 |
|
7 and 9 (Without integral flange seal) |
2 wire: 800H-NPD90 4 wire: 800H-NPD91 |
| ¬ All other devices with the pilot light option utilize a neon lamp. For replacement information consult your local Rockwell Automation sales office or Allen-Bradley distributor. (For Type 1 enclosure use replacement bulb 40268-313-51) | ||
Modifications
Modifications — Factory-Installed
Flange Seal (see applicable codes and laws) — This option provides a Type 3 rating in addition to maintaining a Type 7 & 9 integrity. Add the letter S to the end of the cat. no. Example: Cat. No. 600-TEX9S.
Conduit Openings (Type 4 and Type 7 & 9 only) — If two 3/4 in. (19 mm) pipe taps (one on top and one on bottom) are required, add the number 12 to the end of the cat. no. Example: Cat. No. 600-TEX512. Note: Suffix 12 is only an option for the Type 4 and 7 & 9 enclosures.
Note: All single unit devices are provided with one 3/4 in. (19 mm) pipe tap on the bottom. By reversing the switch base, the pipe tap can be located on the top.
All dual units are provided as standard with one 3/4 in. (19 mm) pipe tap on top and two on the bottom with two threaded plugs included. If 1/2 in. (12.7 mm) openings are required, reducers should be used.
Drain — In order to install a drain on single unit devices (i.e. Cat. No. 600-TEX5) an additional conduit opening is required. See “Conduit Openings” above.
Sealing Well with Integral Flange Seal for Type 3, 7, and 9 — To order this option insert the letter R at the end of the listed cat. no. Example: Cat. No. 600-TEX5R.
Sealing Well without Integral Flange Seal for Type 7 and 9 — To order this option insert the letter K at the end of the listed cat. no. Example: Cat. No. 600-TEX5K.
Approximate Dimensions
Dimensions are shown in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
Open Type without Enclosure
|
| Cat. Nos. | ||
| 600- TOX4 TOX5 TOX49 |
600- TOX109 TOX110 TOX149 |
600- TOX216 |
Type 1 General Purpose Enclosure Surface Mounting
|
| Cat. Nos. | ||
| 600- TAX4 TAX5 TAX49 |
600- TAX109 TAX110 TAX149 |
600- TAX216 |
| Cat. Nos. | ||
| 600- TAX9 TAX10 |
600- TAX142 TAX144 |
600- TAX145 |
| Dimension A in inches (Millimeters) | |
| Key Inserted | 1-1/8 (79.5) |
| Selector Switch | 2-3/4 (70) |
| Toggle Operator | 2-9/16 (65) |
Type 4 Watertight Enclosure;
Type 7 and 9 Hazardous Locations Enclosure
|
| Cat. Nos. | |
| 600- TCX5 | 600- TEX5 |
Type 1 General Purpose Enclosure Flush Mounting
|
|
| Cat. Nos. | |
| 600- TQX4 TQX5 TQX49 |
600- TQX109 TQX110 TQX216 |
| Cat. Nos. | |
| 600- TQX9 TQX142 |
600- TQX144 |
|
Type 4 Watertight Enclosure, Type 7 & 9
|
| Cat. Nos. | |
| 600- TCX9 TCX142 |
600- TEX9 TEX10 |
Type 7 & 9 Hazardous Locations Enclosure
|
| Cat. Nos. | |
| 600- TCA7 TCD75 |
600- TEA7 TED7 |
¬ Lever Type Dimension is 2-17/32 in. (64.5 mm).
T This dimension may vary up to ±1/8 in. (3.2 mm). Mounting holes should be located at time of installation using device as a template.