Bulletin 140M Motor Circuit Protectors

Click to enlarge - 140M-C2N_100 Click to enlarge - 140M-D8N_100
Click to enlarge - 140M-F (MCP) Click to enlarge - MCP Group

Bulletin 140M Motor Circuit Protectors


Your order must include: cat. no. of the Motor Circuit Protector selected and, if required, cat. no. of any accessories.

The Bulletin 140M Motor Circuit Protectors provide short circuit protection for individual motor loads. Factory-installed internal accessories make installation and wiring easy.

General Information

Motor Circuit Protectors may provide the following protective and control functions.

  • Disconnect for Motor Branch Circuit


  • Branch-Circuit, Short-Circuit Protection (Magnetic Protection)


  • Switching (Manual)


    • In North America, electrical codes require that an individual Motor Branch Circuit be protected by a UL/CSA Listed Fuse, Circuit Breaker or Self-Protected Combination Motor Controller.

    140M-C, D and F Frames:

    The 140M-C, D and F frame Motor Circuit Protectors have one UL/CSA Listing – as Manual Motor Controllers (with optional approvals for Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must be applied per the appropriate rules which require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the table on for the specific ratings of each Motor Circuit Protector.

    The 140M-C, D and F Frame Motor Circuit Protectors are also UL/CSA Listed, together with a Bulletin 100C contactor and Bulletin 193 overload relay, as part of our Bulletin 103T and 107T Self-Protected IEC Combination Starters. These starters are then able to provide all of the necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.

    140M-H, J and L Frames:

    The 140M-H, J and L frame Motor Circuit Protectors are UL/CSA Recognized as Circuit Breakers as shown in the table on . They are UL/CSA Recognized, rather than UL/CSA Listed, since they only provide short circuit protection and not thermal overload protection for the motor.

    140M-H, J and L frame Motor Circuit Protectors (MCPs) are also UL/CSA Listed, together with a Bulletin 100C contactor and Bulletin 193 overload relay, as part of our Bulletin 113 IEC Combination Starters. These starters are then able to provide all of the necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.

    Standards Compliance and Certifications

    Standards Compliance

    IEC/EN 60947-1, 2, -4-1, -5-1
    IEC/EN 60204-1
    CSA, C22.2 No.14
    UL 508
    UL 489 (H-, J-, L-, N-Frame)

    Certifications (0.16…45 A)

    CE Marked
    cULus Listed (File No. E54612, Guide No. NLRV, NLRV7)
    CCC

    Certifications (3…1200 A)

    UR Recognized component (File No. E224135, Guide DKPU2)
    CSA Certified (Cleass No. 3211-07)

    Product Line Overview

      Click to enlarge - 140M-C2N_100 Click to enlarge - 140M-D8N_100 Click to enlarge - 140M-F8N_4c Click to enlarge - 140MH8_bw Click to enlarge - 140M-J (MCP) Click to enlarge - 140M-L (MCP) Click to enlarge - 140U-39-7
      C-Frame D-Frame F-Frame H-Frame J-Frame L-Frame N-Frame
    Max. Current Ie 25 A 32 A 45 A 100 A 250 A 600 A 1200 A
    Current Rating 0.16…2.5 A 2.5…32 A 25…45 A 3…100 70…250 125…600 640…1200
    Short Circuit Protection ü ü ü ü ü ü ü
    Standards Compliance:
    CSA 22.2, No. 14 ü ü ü        
    CSA 22.2, No. 5 — — — ü ü ü ü
    UL 508 (Group Install.) ü ü ü        
    UL489 (Recognized) — — — ü ü ü ü
    IEC 60947-2 ü ü ü ü ü ü ü
    CE ü ü ü ü ü ü ü
    CCC ü ü (up to 25 A) ü — — — —
    Accessories
    Ext. Rotary Operator ü ü ü ü ü ü ü
    Flex Cable Operator — — — ü ü ü ü
    Auxiliary Contacts ü ü ü ü ü ü ü
    Trip Indication Contacts ü ü ü ü ü ü ü
      

    Cat. No. Explanation

    140M – C 2 N – A63 – KN – CC – GJ
    a    b c d    e    f    g    h

    a    b    c    d
    Bulletin Number Frame Size and Rating Interrupting Rating / Breaking Capacity Protection Type
    Code Description Code Description Code Description Code Description
    140M Motor Circuit Protectors (MCPs) C 25 A 2 Normal Break N Fixed Mag Only (13 x In)
      D 32 A 8 High Break P Adj Mag Only (less than 13 x In)- MCPs
    F 45 A   R Adj Mag Only (greater than 13 x In) - MCP's
    H 125 A  
    J 250 A
    L 400 A and 600 A
    N 800 A and 1200 A
      
    e    f    g    h
    Current Range Miscellaneous See Aux/Trip Contacts See UV and Shunt Trips See
    Code Description Example      
    A A = .10 A16 = 0.16
    B B = 1.0 B16 = 1.6
    C C = 10 C16 = 16
    D D = 100 D16 = 160
    E E = 1000 E16 = 1600

    Wiring Diagrams

    Click to enlarge - Group Installation-MCP_FINAL
    Group Motor Installation


    3-Phase Power Supply

    Click to enlarge - Multi-Motor Installation-MCP_FINAL
    Multi-Motor Installation

    Product Selection

    Motor Circuit Protectors


    Click to enlarge - 140M-C2N_100 Click to enlarge - 140M-D8N_100 Click to enlarge - 140M-F8N_4c
    Cat. No. 140M-C Cat. No. 140M-D Cat. No. 140M-F

    Rated Operational Current (Ie)
    [A]     		Magnetic Trip Current
    [A]     		Ultimate Interrupting Current [kA] Max. 3-phase Hp Ratings⋆  Max. kW, 3-Phase — AC-3⋆  Cat. No.
    400V
    (Icu)     		480V
    (group motor)     		200V 230V 460V 575V 230V 400/415V 500V 690V
    C-Frame
    0.16 2.1 100 65 — — — — — 0.02 0.06 0.06 140M-C2N-A16
    0.25 3.3 100 65 — — — — — 0.04 0.09 0.09 140M-C2N-A25
    0.4 5.2 100 65 — — — 0.25 0.06 0.09 0.12 0.18 140M-C2N-A40
    0.63 8.2 100 65 — — 0.25 0.33 0.09 0.18 0.18 0.25 140M-C2N-A63
    1 13 100 65 — — 0.5 0.75 0.18 0.25 0.37 0.55 140M-C2N-B10
    1.6 21 100 65 0.25 0.33 1 1 0.25 0.55 0.75 1.1 140M-C2N-B16
    2.5 33 100 65 0.5 0.75 1.5 2 0.37 0.75 1.1 1.8 140M-C2N-B25
    D-Frame
    2.5 33 100 65 0.5 0.75 1.5 2 0.37 0.75 1.1 1.8 140M-D8N-B25
    4 52 100 65 1 1 3 3 0.75 1.5 2.2 3 140M-D8N-B40
    6.3 82 100 65 1.5 2 5 5 1.5 2.2 3 4 140M-D8N-B63
    10 130 100 65 3 3 7.5 10 2.2 4 6.3 7.5 140M-D8N-C10
    16 208 100 65 5 5 10 15 4 7.5 10 13 140M-D8N-C16
    25 325 65 30 7.5 7.5 20 20 5.5 11 15 22 140M-D8N-C25
    32 448 50 30 7.5 10 25 30 7.5 15 20 25 140M-D8N-C32
    F-Frame
    25 325 100 65 7.5 10 20 25 6.3 11 15 22 140M-F8N-C25
    32 416 65 65 7.5 10 25 30 7.5 15 20 30 140M-F8N-C32
    45 585 65 65 10 15 30 40 13 22 30 40 140M-F8N-C45
      
    ⋆ Horsepower/kW ratings shown in the table above are for reference. The final selection of the manual starter depends on the actual motor full load current.

    Note:In applications with 140M-C_N, 140M-D_N and 140M-F_N as the short circuit protection device of heavy duty starting motors, the rated operational current Ie of the above devices must be over-dimensioned with following factors:

                 CLASS 10 = 1.00
                 CLASS 15 = 1.22
                 CLASS 20 = 1.42
                 CLASS 25 = 1.58
                 CLASS 30 = 1.73


    Motor Circuit Protectors


    Click to enlarge - 140MH8_bw Click to enlarge - 140M-J (MCP) Click to enlarge - 140M-L (MCP)
    Cat. No. 140M-H Cat. No. 140M-J Cat. No. 140M-L

    Rated Operational Current (Ie)
    [A]     		Magnetic Trip Current [A] 3-phase Hp Ratings⋆  Max. kW, 3-Phase — AC-3⋆  Cat. No.‡ 
    Cam Setting
    A B C D E F G H I 200V 230V 460V 575V 230V 400/415V 500V 690V
    H-Frame
    3 9 15 21 27 30 33 — — — 0.5 0.5 1.5 2 0.6 0.75 1.1 1.5 140M-H8P-B30
    7 21 35 49 63 70 77 — — — 1.5 2 3 5 1.1 2.2 3 4 140M-H8P-B70
    15 45 75 100 135 150 165 — — — 3 3 10 10 3 5.5 7.5 11 140M-H8P-C15
    30 90 150 210 270 300 330 — — — 7.5 10 20 25 5.5 11 15 22 140M-H8P-C30
    50 150 250 350 450 500 550 — — — 15 15 30 40 11 22 22 37 140M-H8P-C50
    70 210 350 490 630 700 770 — — — 20 25 50 60 15 30 37 55 140M-H8P-C70
    100 300 500 700 900 1000 1100 — — — 25 30 60 75 22 45 55 75 140M-H8P-D10
    100 500 700 900 1100 1300 1500 — — — 30 30 75 100 30 55 75 110 140M-H8R-D10
    J-Frame
    100 500 600 700 800 900 1000 — — — 30 30 75 100 22 37 45 55 140M-J8P-D10
    125 625 750 875 1000 1125 1250 — — — 40 40 100 125 22 45 55 90 140M-J8P-D12
    150 750 900 1050 1200 1350 1500 — — — 50 50 100 150 30 55 75 110 140M-J8P-D15
    175 875 1050 1225 1400 1575 1750 — — — 50 60 125 150 37 55 90 132 140M-J8P-D17
    200 1000 1200 1400 1600 1800 2000 — — — 60 75 150 200 45 75 90 132 140M-J8P-D20
    225 1125 1350 1575 1800 2025 2250 — — — 75 75 150 200 55 90 110 160 140M-J8P-D22
    250 1250 1500 1750 2000 2250 2500 — — — 75 100 200 250 55 90 132 160 140M-J8P-D25
    L-Frame
    225 1125 1265 1410 1545 1690 1830 1970 2110 2250 50 60 125 150 55 90 110 160 140M-L8P-D22
    250 1250 1405 1560 1720 1875 2030 2185 2340 2500 60 75 150 200 55 90 132 160 140M-L8P-D25
    300 1500 1690 1875 2060 2250 2440 2625 2810 3000 75 75 150 200 55 110 160 200 140M-L8P-D30
    350 1750 1970 2190 2410 2625 2840 3065 3285 3500 75 100 200 250 75 132 160 250 140M-L8P-D35
    400 2000 2250 2500 2750 3000 3250 3500 3750 4000 100 100 250 300 90 160 200 250 140M-L8P-D40
    450 2250 2530 2810 3098 3375 3660 3940 4220 4500 100 125 250 350 110 160 200 315 140M-L8P-D45
    500 2500 2810 3125 3440 3750 4375 4660 4690 5000 125 150 300 400 110 200 250 355 140M-L8P-D50
    600 3000 3375 3760 4110 4500 4880 5250 5630 6000 150 150 350 450 132 250 315 450 140M-L8P-D60
    N-Frame
    800 1600 2400 3200 4000 4800 5600 6400 — — 150 200 400 500 160 250 355 500 140M-N8P-D80
    1200 2400 3600 4800 6000 7200 8400 9600 — — 250 300 600 700 200 250 500 710 140M-N8P-E12
      
    ⋆ The Hp and kW ratings shown are for reference only. They allow for a magnetic trip setting of at least up to 13X the motor FLA. However, the final selection of the MCP should be made based on motor full load current and the requirements of local electrical codes.
    ‡ The interrupting rating for MCPs is dependent upon the controller used. Please contact your local Rockwell Automation sales office or Allen-Bradley distributor for further information.

    Application Ratings

    UL/CSA Listed Application Ratings — Motor Protection Circuit Breaker (MPCB) Only

    Cat. No. UL 508 — Manual Motor Controller UL 508 Self-Protected
    (Type E) Combination
    Motor Controller     		UL 489 Inverse Time
    C.B. w/UL 508 Motor Overload Protection
    Max. Fuse or C.B. per NEC Group Motor Installation Motor Disconnect Tap Conductor Protection
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA]
    480V 600V 480V 600V 480V 600V 480Y/277V§  600Y/347V§  480V 600V
    C-Frame
    140M-C2E-A16 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-A25 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-A40 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-A63 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-B10 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-B16 450 65 47 65 47 65 47 65 47 — —
    140M-C2E-B25 450 65 30 65 30 65 30 65 30 — —
    140M-C2E-B40 450 65 25 65 25 65 25 65 25 — —
    140M-C2E-B63 450 65 30 65 30 65 — 65 — — —
    140M-C2E-C10 450 65 30 65 30 65 — 65 — — —
    140M-C2E-C16 450 30 30 30 30 30 — 30 — — —
    140M-C2E-C20 450 30 30 10 10 10 — 10 — — —
    140M-C2E-C25 450 25 10 10 5 — — — — — —
    140M-C2E-C29 450 25 30 10 — — — — — — —
    140M-C2E-C32 450 25 30 10 — — — — — — —
    D-Frame
    140M-D8E-B25 450 65 30 65 30 65 30 65 30 — —
    140M-D8E-B40 450 65 30 65 30 65 30 65 30 — —
    140M-D8E-B63 450 65 30 65 30 65 30 65 30 — —
    140M-D8E-C10 450 65 30 65 30 65 30 65 30 — —
    140M-D8E-C16 450 65 30 65 30 65 30 65 30 — —
    140M-D8E-C20 450 65 30 65 30 65 — 65 — — —
    140M-D8E-C25 450 30 30 30 30 30 — 30 — — —
    140M-D8E-C29 450 30 30 30 18 — — — — — —
    140M-D8E-C32 450 30 30 30 18 — — — — — —
    F-Frame
    140M-F8E-C10 600 65 30 65 30 65 30 65 30 — —
    140M-F8E-C16 600 65 30 65 30 65 30 65 30 — —
    140M-F8E-C20 600 65 30 65 30 65 30 65 30 — —
    140M-F8E-C25 600 65 30 65 30 65 30 65 30 — —
    140M-F8E-C32 600 65 30 65 30 65 30 65 30 — —
    140M-F8E-C45 600 65 18 65 18 65 — 65 — — —
    CMN-Frame
    140-CMN-2500 1000 65 42 — — — — — — — —
    140-CMN-4000 1000 65 42 — — — — — — — —
    140-CMN-6300 1000 42 18 — — — — — — — —
    140-CMN-9000 1000 35 10 — — — — — — — —
    I-Frame
    140M-I8E-C80 — — — — — — — — — 65 30
    140M-I8E-D10 — — — — — — — — — 65 30
    140M-I8E-D16 — — — — — — — — — 65 30
    140M-I8E-D20 — — — — — — — — — 65 30
    J-Frame
    140M-J2E-C50 — — — — — — — — — 25 18
    140M-J2E-D10 — — — — — — — — — 25 18
    140M-J2E-D16 — — — — — — — — — 25 18
    140M-J2E-D25 — — — — — — — — — 25 18
    140M-J8E-C50 — — — — — — — — — 65 25
    140M-J8E-D10 — — — — — — — — — 65 25
    140M-J8E-D16 — — — — — — — — — 65 25
    140M-J8E-D25 — — — — — — — — — 65 25
    L-Frame
    140M-L2E-D25 — — — — — — — — — 25 18
    140M-L2E-D40 — — — — — — — — — 25 18
    140M-L2E-D63 — — — — — — — — — 25 18
    140M-L8E-D25 — — — — — — — — — 65 35
    140M-L8E-D40 — — — — — — — — — 65 35
    140M-L8E-D63 — — — — — — — — — 65 35
      
    §  For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.

    Cat. No. UL 508 Manual Motor Controller UL 508 Self-Protected
    (Type E) Combination
    Motor Controller
    Max. Fuse or C.B. per NEC Group Motor Installation Motor Disconnect Tap Conductor Protection
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA]
    480V 600V 480V 600V 480V 600V 480Y/277V§  600Y/347V§ 
    C-Frame
    140M-C2T-A16 450 65 47 65 47 65 47 65 47
    140M-C2T-A25 450 65 47 65 47 65 47 65 47
    140M-C2T-A40 450 65 47 65 47 65 47 65 47
    140M-C2T-A63 450 65 47 65 47 65 47 65 47
    140M-C2T-B10 450 65 47 65 47 65 47 65 47
    140M-C2T-B16 450 65 47 65 47 65 30 65 30
    140M-C2T-B25 450 65 25 65 25 65 25 65 25
    140M-C2T-B40 450 65 30 65 30 65 — 65 —
    140M-C2T-B63 450 65 30 65 30 65 — 65 —
    140M-C2T-C10 450 30 30 30 30 30 — 30 —
    140M-C2T-C16 450 30 30 10 10 10 — 10 —
    D-Frame
    140M-D8T-C16 450 65 30 65 30 65 30 65 30
    140M-D8T-C20 450 30 30 30 30 30 — 30 —
    F-Frame
    140M-F8T-C25 600 65 30 65 30 65 30 65 30
    140M-F8T-C32 600 65 18 65 18 65 18 65 18
      
    §  For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.

    UL Listed Application Ratings — Motor Circuit Protectors Only♣ 

    Cat. No. UL 508 Manual Motor Controller UL 489 Instantaneous Trip Circuit Breaker (Magnetic Only)
    Max. Fuse or C.B. per NEC Group Motor Installation Motor Disconnect Motor Circuit Protector
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Max. Short Circuit Current [kA]§ 
    480V 600V 480V 600V 480V 600V
    C-Frame
    140M-C2N-A16 450 65 47 65 47 — —
    140M-C2N-A25 450 65 47 65 47 — —
    140M-C2N-A40 450 65 47 65 47 — —
    140M-C2N-A63 450 65 47 65 47 — —
    140M-C2N-B10 450 65 47 65 47 — —
    140M-C2N-B16 450 65 47 65 47 — —
    140M-C2N-B25 450 65 30 65 30 — —
    D-Frame
    140M-D8N-B25 450 65 30 65 30 — —
    140M-D8N-B40 450 65 30 65 30 — —
    140M-D8N-B63 450 65 30 65 30 — —
    140M-D8N-C10 450 65 30 65 30 — —
    140M-D8N-C16 450 65 30 65 30 — —
    140M-D8N-C25 450 30 30 30 30 — —
    140M-D8N-C32 450 30 30 30 18 — —
    F-Frame
    140M-F8N-C25 600 65 30 65 30 — —
    140M-F8N-C32 600 65 30 65 30 — —
    140M-F8N-C45 600 65 18 65 18 — —
    H-Frame
    140M-H8P-B30 — — — — — 65 30
    140M-H8P-B70 — — — — — 65 30
    140M-H8P-C15 — — — — — 65 30
    140M-H8P-C30 — — — — — 65 30
    140M-H8P-C50 — — — — — 65 30
    140M-H8P-C70 — — — — — 65 30
    140M-H8P-D10 — — — — — 65 30
    140M-H8R-D10 — — — — — 65 30
    J-Frame
    140M-J8P-C70 — — — — — 65 30
    140M-J8P-C90 — — — — — 65 30
    140M-J8P-D10 — — — — — 65 30
    140M-J8P-D12 — — — — — 65 30
    140M-J8P-D15 — — — — — 65 30
    140M-J8P-D17 — — — — — 65 30
    140M-J8P-D20 — — — — — 65 30
    140M-J8P-D22 — — — — — 65 30
    140M-J8P-D25 — — — — — 65 30
    L-Frame
    140M-L8P-D22 — — — — — 65 30
    140M-L8P-D25 — — — — — 65 30
    140M-L8P-D30 — — — — — 65 30
    140M-L8P-D35 — — — — — 65 30
    140M-L8P-D40 — — — — — 65 30
    140M-L8P-D45 — — — — — 65 30
    140M-L8P-D50 — — — — — 65 30
    140M-L8P-D60 — — — — — 65 30
    N-Frame
    140M-N8P-D80 — — — — — 65 35
    140M-N8P-E12 — — — — — 65 35
      
    ♣ Separate overload protection is required.
    § The interrupting rating for MCPs is dependent upon the controller used. Contact your local Rockwell Automation sales office or Allen-Bradley distributor for further information.

    UL Listed Application Ratings - Motor Protection Circuit Breakers with Bulletin 100-K Contactors

    Cat. No. UL 508 Manual Motor Controller UL 508 Type F
    Combination
    Motor Controller     		UL 508 Type E
    Self-Protected Combination
    Motor Controller
    Max. Fuse or C.B. per NEC Minimum Contactor Size Group Motor Installation Motor Disconnect
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Minimum Contactor Size Max. Short Circuit Current [kA] Minimum Contactor Size Max. Short Circuit Current [kA]
    480V 600V 480V 600V 480Y/277V♣  600Y/347V♣  480Y/277V♣  600Y/347V♣ 
    C-Frame
    140M-C2E-A16 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-A25 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-A40 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-A63 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-B10 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-B16 450 100-K05 65 47 65 47 100-K05 65 47 — — —
    140M-C2E-B25 450 100-K05 65 30 65 30 100-K05 65 30 — — —
    140M-C2E-B40 450 100-K05 65 30 65 30 100-K05 65 30 — — —
    140M-C2E-B63 450 100-K05 65 30 65 30 100-K05 65 — — — —
    140M-C2E-C10 450 100-K09 65 30 65 30 100-K09 65 — — — —
    140M-C2E-C16 450 100-K12 30 30 30 30 100-K12 30 — — — —
    D-Frame
    140M-D8E-B25 450 100-K05 65 30 65 30 100-K05 65 30 — — —
    140M-D8E-B40 450 100-K05 65 30 65 30 100-K05 65 30 — — —
    140M-D8E-B63 450 100-K05 65 30 65 30 100-K05 65 30 — — —
    140M-D8E-C10 450 100-K09 65 30 65 30 100-K09 65 30 — — —
    140M-D8E-C16 450 100-K12 65 30 65 30 100-K12 65 30 — — —
      
    ♣ For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.

    UL Listed Application Ratings - Motor Protection Circuit Breakers with Bulletin 100-C Contactors

    Cat. No. UL 508 Manual Motor Controller UL 508 Type F
    Combination
    Motor Controller     		UL 508 Type E
    Self-Protected Combination
    Motor Controller
    Max. Fuse or C.B. per NEC Minimum Contactor Size Group Motor Installation Motor Disconnect
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Minimum Contactor Size Max. Short Circuit Current [kA] Minimum Contactor Size Max. Short Circuit Current [kA]
    480V 600V 480V 600V 480Y/277V♣  600Y/347V♣  480Y/277V♣  600Y/347V♣ 
    C-Frame
    140M-C2E-A16 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-A25 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-A40 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-A63 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-B10 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-B16 450 100-C09 65 47 65 47 100-C09 65 47 100-C09 65 47
    140M-C2E-B25 450 100-C09 65 30 65 30 100-C09 65 30 100-C09 65 30
    140M-C2E-B40 450 100-C09 65 30 65 30 100-C09 65 30 — 65 25
    140M-C2E-B63 450 100-C09 65 30 65 30 100-C09 65 — — 65 —
    140M-C2E-C10 450 100-C09 65 30 65 30 100-C09 65 — — 65 —
    140M-C2E-C16 450 100-C12 30 30 30 25 100-C12 30 — — 30 —
    140M-C2E-C20 450 100-C16 30 30 30 30 100-C23 10 — — 10 —
    140M-C2E-C25 450 100-C23 30 30 10 10 — — — — — —
    450 100-C30 30 30 30 30 — — — — — —
    140M-C2E-C29 450 100-C30 30 30 10 10 — — — — — —
    140M-C2E-C32 450 100-C37 30 30 10 10 — — — — — —
    D-Frame
    140M-D8E-B25 450 100-C09 65 30 65 30 100-C09 65 30 100-C09 65 30
    — — — — — — — — — 100-C23 65 30
    140M-D8E-B40 450 100-C09 65 30 65 30 100-C09 65 30 100-C23 65 30
    140M-D8E-B63 450 100-C09 65 30 65 30 100-C09 65 30 100-C30 65 30
    140M-D8E-C10 450 100-C09 65 30 65 30 100-C09 65 30 100-C30 65 30
    140M-D8E-C16 450 100-C12 65 30 65 30 100-C12 65 30 100-C30 65 30
    140M-D8E-C20 450 100-C23 65 30 65 30 100-C23 65 — 100-C30 65 —
    140M-D8E-C25 450 100-C23 65 30 65 30 100-C23 30 — 100-C30 30 —
    140M-D8E-C29 450 100-C30 65 30 65 10 — — — — — —
    140M-D8E-C32 450 100-C37 65 30 65 10 — — — — — —
    F-Frame
    140M-F8E-C10 600 100-C30 65 30 65 30 100-C30 65 30 100-C30 65 30
    140M-F8E-C16 600 100-C30 65 30 65 30 100-C30 65 30 100-C30 65 30
    140M-F8E-C20 600 100-C30 65 30 65 30 100-C30 65 30 100-C30 65 30
    140M-F8E-C25 600 100-C30 65 30 65 30 100-C30 65 30 100-C30 65 30
    140M-F8E-C32 600 100-C30 65 30 65 30 100-C30 65 30 100-C30 65 30
    140M-F8E-C45 600 100-C37 65 18 65 18 100-C37 65 — 100-C37 65 —
    CMN-Frame
    140-CMN-2500 1000 100-C16 65 42 — — — — — — — —
    140-CMN-4000 1000 100-C30 65 42 — — — — — — — —
    140-CMN-6300 1000 100-C43 42 18 — — — — — — — —
    140-CMN-9000 1000 100-C72 35 10 — — — — — — — —
      
    ♣ For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.

    UL Listed Application Ratings - Motor Circuit Protectors with Bulletin 100-C Contactors♣ 

    Cat. No. UL 508 Manual Motor Controller UL 508 Type E (Self-Protected) Combination Motor Controller
    Max. Fuse or C.B. per NEC Minimum Contactor Size Group Motor Installation Motor Disconnect
    Max. Short Circuit Current [kA] Max. Short Circuit Current [kA] Minimum Contactor Size Max. Short Circuit Current [kA] Max. Short Circuit Current [kA]
    480V 600V 480V 600V 480Y/277V‡  600Y/347V‡ 
    C-Frame
    140M-C2N-A16 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-A25 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-A40 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-A63 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-B10 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-B16 450 100-C09 65 47 65 47 100-C09 65 47
    140M-C2N-B25 450 100-C09 65 30 65 30 100-C09 65 —
    D-Frame
    140M-D8N-B25 450 100-C09 65 30 65 30 100-C09 65 —
    — — — — — — 100-C23 65 30
    140M-D8N-B40 450 100-C09 65 30 65 30 100-C23 65 30
    140M-D8N-B63 450 100-C09 65 30 65 30 100-C30 65 30
    140M-D8N-C10 450 100-C09 65 30 65 30 100-C30 65 30
    140M-D8N-C16 450 100-C12 65 30 65 30 100-C30 65 30
    140M-D8N-C25 450 100-C23 30 30 30 30 100-C30 65 —
    140M-D8N-C32 450 100-C37 65 10 65 10 — — —
    F-Frame
    140M-F8N-C25 600 100-C23 65 30 65 30 100-C30 65 30
    140M-F8N-C32 600 100-C30 65 30 65 30 100-C30 65 30
    140M-F8N-C45 600 100-C37 65 18 65 18 100-C37 65 —
      
    ♣ Separate overload protection is required.
    ‡ For full-voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.

    Definition of Type 2 Short Circuit Coordination:


    In the event of short circuit, fast-opening, current-limiting Bulletin 140M Motor Protection Circuit Breakers make it possible to build economical, fully short-circuit coordinated starter combinations with Type 2 coordination.

    Type 2 Coordination 400V

    Cat. No. Max. Short Circuit Current [kA] For Use With Contactors Below (or larger)
    Standard Motor Protection High Inrush Motor Protection Motor Circuit Protection 400V
    C-Frame
    140M-C2E-A16 — 140M-C2N-A16 100 100-C09
    140M-C2E-A25 140M-C2T-A16 140M-C2N-A25 100 100-C09
    140M-C2E-A40 140M-C2T-A25 140M-C2N-A40 100 100-C09
    140M-C2E-A63 140M-C2T-A40 140M-C2N-A63 100 100-C09
    140M-C2E-B10 140M-C2T-A63 140M-C2N-B10 100 100-C09
    140M-C2E-B16 140M-C2T-B10 140M-C2N-B16 100 100-C09
    140M-C2E-B25 140M-C2T-B16 140M-C2N-B25 50 100-C09
    140M-C2E-B40 140M-C2T-B25 — 50 100-C09
    140M-C2E-B63 140M-C2T-B40 — 50 100-C09
    140M-C2E-C10 140M-C2T-B63 — 50 100-C09
    140M-C2E-C16 140M-C2T-C10 — 50 100-C12⋆ 
    140M-C2E-C20 140M-C2T-C16 — 50 100-C23
    140M-C2E-C25 — — 15 100-C30
    140M-C2E-C29 — — 15 100-C30
    140M-C2E-C32 — — 15 100-C37
    D-Frame
    140M-D8E-B25 — 140M-D8N-B25 100 100-C09
    140M-D8E-B40 — 140M-D8N-B40 100 100-C09
    140M-D8E-B63 — 140M-D8N-B63 100 100-C09
    140M-D8E-C10 — 140M-D8N-C10 65 100-C09
    140M-D8E-C16 — 140M-D8N-C16 65 100-C12
    140M-D8E-C20 140M-D8T-C16 — 65 100-C23
    140M-D8E-C25 140M-D8T-C20 140M-D8N-C25 50 100-C23
    140M-D8E-C29 — — 65 100-C30
    140M-D8E-C32 — 140M-D8N-C32 65 100-C37
    F-Frame
    140M-F8E-C10 — — 100 100-C09
    140M-F8E-C16 — — 100 100-C12
    140M-F8E-C20 — — 100 100-C23
    140M-F8E-C25 — 140M-F8N-C25 100 100-C30
    140M-F8E-C32 140M-F8T-C25 140M-F8N-C32 100 100-C30
    140M-F8E-C45 140M-F8T-C32 140M-F8N-C45 100 100-C37
    CMN-Frame
    140-CMN-2500 — — 65 100-C16
    140-CMN-4000 — — 65 100-C30
    140-CMN-6300 — — 42 100-C43
    140-CMN-9000 — — 35 100-C72
      
    ⋆ Cat. No. 100-C16 contactors Type 1 only

    Type 2 Coordination 480V

    Cat. No. Max. Short Circuit Current [kA] For Use With Contactors Below (or larger)
    Standard Motor Protection High Inrush Motor Protection Motor Circuit Protection 480V
    C-Frame
    140M-C2E-A16 — 140M-C2N-A16 65 100-C09
    140M-C2E-A25 140M-C2T-A16 140M-C2N-A25 65 100-C09
    140M-C2E-A40 140M-C2T-A25 140M-C2N-A40 65 100-C09
    140M-C2E-A63 140M-C2T-A40 140M-C2N-A63 65 100-C09
    140M-C2E-B10 140M-C2T-A63 140M-C2N-B10 65 100-C09
    140M-C2E-B16 140M-C2T-B10 140M-C2N-B16 65 100-C09
    140M-C2E-B25 140M-C2T-B16 140M-C2N-B25 50 100-C16
    140M-C2E-B40 140M-C2T-B25 — 50 100-C30
    140M-C2E-B63 140M-C2T-B40 — 50 100-C30
    140M-C2E-C10 140M-C2T-B63 — 50 100-C30
    140M-C2E-C16 140M-C2T-C10 — 10 100-C30
    140M-C2E-C20 140M-C2T-C16 — 10 100-C30
    140M-C2E-C25 — — 10 100-C30
    140M-C2E-C29 — — 10 100-C30
    140M-C2E-C32 — — 10 100-C37
    D-Frame
    140M-D8E-B25 — 140M-D8N-B25 65 100-C09
    140M-D8E-B40 — 140M-D8N-B40 65 100-C09
    140M-D8E-B63 — 140M-D8N-B63 65 100-C09
    140M-D8E-C10 — 140M-D8N-C10 65 100-C09
    140M-D8E-C16 — 140M-D8N-C16 65 100-C12
    140M-D8E-C20 140M-D8T-C16 — 65 100-C23
    140M-D8E-C25 140M-D8T-C20 140M-D8N-C25 65 100-C23
    140M-D8E-C29 — — 65 100-C30
    140M-D8E-C32 — 140M-D8N-C32 65 100-C37
    F-Frame
    140M-F8E-C10 — — 65 100-C09
    140M-F8E-C16 — — 65 100-C12
    140M-F8E-C20 — — 65 100-C23
    140M-F8E-C25 — 140M-F8N-C25 65 100-C30
    140M-F8E-C32 140M-F8T-C25 140M-F8N-C32 65 100-C30
    140M-F8E-C45 140M-F8T-C32 140M-F8N-C45 65 100-C37
    CMN-Frame
    140-CMN-2500 — — 65 100-C16
    140-CMN-4000 — — 65 100-C30
    140-CMN-6300 — — 42 100-C43
    140-CMN-9000 — — 35 100-C72
      

    Type 2 Coordination 600V

    Cat. No. Max. Short Circuit Current [kA] For Use With Contactors Below (or larger)
    Standard Motor Protection High Inrush Motor Protection Motor Circuit Protection 600V
    C-Frame
    140M-C2E-A16 — 140M-C2N-A16 47 100-C09
    140M-C2E-A25 140M-C2T-A16 140M-C2N-A25 47 100-C09
    140M-C2E-A40 140M-C2T-A25 140M-C2N-A40 47 100-C09
    140M-C2E-A63 140M-C2T-A40 140M-C2N-A63 47 100-C09
    140M-C2E-B10 140M-C2T-A63 140M-C2N-B10 47 100-C09
    140M-C2E-B16 140M-C2T-B10 140M-C2N-B16 47 100-C09
    140M-C2E-B25 140M-C2T-B16 140M-C2N-B25 10 100-C16
    140M-C2E-B40 140M-C2T-B25 — 10 100-C16
    140M-C2E-B63 140M-C2T-B40 — 5 100-C23
    140M-C2E-C10 140M-C2T-B63 — 5 100-C30
    140M-C2E-C16 140M-C2T-C10 — 5 100-C30
    140M-C2E-C20 140M-C2T-C16 — 5 100-C30
    140M-C2E-C25 — — 5 100-C30
    140M-C2E-C29 — — 5 100-C30
    140M-C2E-C32 — — 5 100-C37
    D-Frame
    140M-D8E-B25 — 140M-D8N-B25 30 100-C30
    140M-D8E-B40 — 140M-D8N-B40 30 100-C30
    140M-D8E-B63 — 140M-D8N-B63 30 100-C30
    140M-D8E-C10 — 140M-D8N-C10 30 100-C30
    140M-D8E-C16 — 140M-D8N-C16 30 100-C30
    140M-D8E-C20 140M-D8T-C16 — 5 100-C30
    140M-D8E-C25 140M-D8T-C20 140M-D8N-C25 5 100-C30
    140M-D8E-C29 — — 10 100-C30
    140M-D8E-C32 — 140M-D8N-C32 10 100-C37
    F-Frame
    140M-F8E-C10 — — 30 100-C30
    140M-F8E-C16 — — 30 100-C30
    140M-F8E-C20 — — 30 100-C30
    140M-F8E-C25 — 140M-F8N-C25 30 100-C30
    140M-F8E-C32 140M-F8T-C25 140M-F8N-C32 30 100-C30
    140M-F8E-C45 140M-F8T-C32 140M-F8N-C45 10 100-C37
    CMN-Frame
    140-CMN-2500 — — 42 100-C16
    140-CMN-4000 — — 42 100-C30
    140-CMN-6300 — — 18 100-C43
    140-CMN-9000 — — 10 100-C72
      

    Accessories

    Description Connection Diagram ‡  For Use With Cat. No.
      Operator Position ⋆  Term. No. Description
    OFF ON Tripped
    Click to enlarge - 140M-14-1 Click to enlarge - 140M-14-2 Click to enlarge - 140M-14-3
    Click to enlarge - 140M-14-6 Front-Mounted Auxiliary Contact
  • 1-pole or 2-pole

  • No additional space required

  • Only 1 per device
    		•  O X O 13-14
    N.O. Aux     		Click to enlarge - 140M-C-AFA10_Dia 140M-C, D, F; 140U-D (UL489 only in combination with 140M-C-AFC) 140M-C-AFA10
    X O X 11-12 N.C. Aux Click to enlarge - 140M-C-AFA01_Dia 140M-C-AFA01
    Click to enlarge - 140M-14-8 O X O
    13-14
    		 N.O. Aux Click to enlarge - 140M-C-AFA11_Dia 140M-C, D, F; 140U-D (UL489 only in combination with 140M-C-AFC) 140M-C-AFA11
    X O X 21-22 N.C. Aux
    O X O
    13-14
    		 N.O. Aux Click to enlarge - 140M-C-AFA20_Dia 140M-C-AFA20
    O X O 23-24 N.O. Aux
    X O X
    11-12
    		 N.C. Aux Click to enlarge - 140M-C-AFA02_Dia 140M-C-AFA02
    X O X 21-22 N.C. Aux
    Click to enlarge - 140M-14-13 Right Side-Mounted Auxiliary Contact
  • 2-pole

  • Adds 9 mm to the width of the device

  • Two per MPCB
    		•  O X O
    33-34
    		 N.O. Aux Click to enlarge - 140M-C-ASA20_Dia 140M-C, D, F 140M-C-ASA20
    O X O 43-44 N.O. Aux
    X O X
    31-32
    		 N.C. Aux Click to enlarge - 140M-C-ASA02_Dia 140M-C, D, F 140M-C-ASA02
    X O X 41-42 N.C. Aux
    O X O
    33-34
    		 N.O. Aux Click to enlarge - 140M-C-ASA11_Dia 140M-C, D, F 140M-C-ASA11
    X O X 41-42 N.C. Aux
      
    ⋆ X = Contact Closed; O = Contact Open
    ‡ 
    Click to enlarge - 140M-14-15

    Description Connection Diagram ‡  For Use With Cat. No.
      Operator Position ⋆  Term.
    No.     		Description
    OFF ON Tripped
    Click to enlarge - 140M-14-1 Click to enlarge - 140M-14-2 Click to enlarge - 140M-14-3
    Click to enlarge - 140M-15-4 Front-Mounted Trip Contact
  • 2-pole

  • Indicates tripping of device

  • No additional space required
    		•  O X O 13-14 N.O. Aux Click to enlarge - 140M-C-AFAR10A10_Dia 140M-C, D, F; 140U-D (UL489 only in combination with 140M-C-AFC) 140M-C-AFAR10A10
    O O X 27-28 N.O. Trip
    (Short-Circuit & Overload)
    X O X 11-12 N.C. Aux Click to enlarge - 140M-C-AFAR10A01_Dia 140M-C-AFAR10A01
    O O X 27-28 N.O. Trip
    (Short-Circuit & Overload)
    Click to enlarge - 140M-15-9 Right-Side Mounted Trip Contact
  • 2-pole

  • Indicates tripping of motor protection circuit breaker

  • Adds 9 mm to the width of the circuit breaker

  • One only per MPCB

  • A right-side mounted auxiliary contact may be tandem mounted on top of this trip contact
    		•  O O X 57-58 N.O. Trip
    (Short-Circuit & Overload)     		Click to enlarge - 140M-C-ASAR10M10_Dia 140M-C, D, F 140M-C-ASAR10M10
    O O X 67-68 N.O. Trip
    (Short-Circuit)
    O O X 57-58 N.O. Trip
    (Short-Circuit & Overload)     		Click to enlarge - 140M-C-ASAR10M01_Dia 140M-C, D, F 140M-C-ASAR10M01
    X X O 65-66 N.C. Trip
    (Short-Circuit)
    X X O 55-56 N.C. Trip
    (Short-Circuit & Overload)     		Click to enlarge - 140M-15-10 140M-C, D, F 140M-C-ASAR01M10
    O O X 67-68 N.O. Trip
    (Short-Circuit)
    X X O 55-56 N.C. Trip
    (Short-Circuit & Overload)     		Click to enlarge - 140M-15-11 140M-C, D, F 140M-C-ASAR01M01
    X X O 65-66 N.C. Trip
    (Short-Circuit)
    O O X 77-78 N.O. Trip
    (Short-Circuit)     		Click to enlarge - 140M-15-12 140M-C, D, F 140M-C-ASAM11
    X X O 65-66 N.C. Trip
    (Short-Circuit)
      
    ⋆ X = Contact Closed; O = Contact Open
    ‡ 
    Click to enlarge - 140M-14-15

    Accessories — Screwless

    Description Connection Diagram ‡  For Use With Cat. No.
      Operator Position ⋆  Term.
    No.     		Description
    OFF ON Tripped
    Click to enlarge - 140M-14-1 Click to enlarge - 140M-14-2 Click to enlarge - 140M-14-3
    Click to enlarge - 140M-RC-AFA11 Product Shot_BW Front-Mounted Auxiliary Contact
    1-pole or 2-pole
    No additional space required
    - Only 1 per MPCB     		O X O 13-14
    N.O. Aux     		Click to enlarge - 140M-C-AFA10_Dia 140M-C, D, F; 140M-RC 140M-RC-AFA10
    X O X 11-12 N.C. Aux Click to enlarge - 140M-C-AFA01_Dia 140M-RC-AFA01
    O X O
    13-14
    		 N.O. Aux Click to enlarge - 140M-C-AFA11_Dia 140M-C, D, F; 140M-RC 140M-RC-AFA11
    X O X 21-22 N.C. Aux
    O X O
    13-14
    		 N.O. Aux Click to enlarge - 140M-C-AFA20_Dia 140M-RC-AFA20
    O X O 23-24 N.O. Aux
    Click to enlarge - 140M-RC-AFA11 Product Shot_BW Front-Mounted Trip Contact
    2-pole
    Indicates tripping of device
    No additional space required     		O X O
    13-14
    		 N.O. Aux Click to enlarge - 140M-C-AFAR10A10_Dia 140M-C, D, F; 140M-RC 140M-RC-AFAR10A01
    O O X 27-28 N.O. Trip
    (Short-Circuit & Overload)
    X O X
    11-12
    		 N.C. Aux Click to enlarge - 140M-C-AFAR10A01_Dia 140M-RC-AFAR10A10
    O O X 27-28 N.O. Trip
    (Short-Circuit & Overload)
      
    ⋆ X = Contact Closed; O = Contact Open
    ‡ 
    Click to enlarge - 140M-14-15

    Description Connection Diagram‡  For Use With Cat. No.
      Operator Position⋆  Term.
    No.     		Description
    OFF ON Tripped
    Click to enlarge - 140M-14-1 Click to enlarge - 140M-14-2 Click to enlarge - 140M-14-3
    Click to enlarge - 140M-16-4 Front-Mounted Auxiliary Contact
  • Internal

  • 2-pole

  • 1 per MPCB
    		•  O X O 13-14 N.O. Aux Click to enlarge - 140M-16-5 140-CMN 140-CA20
    O X O 23-24 N.O. Aux
    X O X 11-12 N.C. Aux Click to enlarge - 140M-16-5-2 140-CMN 140-CA02
    X O X 21-22 N.C. Aux
    O X O 13-14 N.O. Aux Click to enlarge - 140M-16-7 140-CMN 140-CA11
    X O X 21-22 N.C. Aux
    Click to enlarge - 140M-16-10 Front-Mounted Trip-Indicating Auxiliary Contact
  • Internal

  • 2-pole

  • 1 per MPCB
    		•  O O X 37-38 N.O. Trip (Overload) Click to enlarge - 140M-16-8 140-CMN 140-CT10-10
    O O X 43-44 N.O. Trip (Short-Circuit)
    X X O 35-36 N.C. Trip (Overload) Click to enlarge - 140M-16-9 140-CMN 140-CT01-01
    X X O 41-42 N.C. Trip (Short-Circuit)
    X X O 35-36 N.C. Trip (Overload) Click to enlarge - 140M-16-11 140-CMN 140-CT01-10
    O O X 43-44 N.O. Trip (Short-Circuit)
    O O X 37-38 N.O. Trip (Overload) Click to enlarge - 140M-16-12 140-CMN 140-CT10-01
    X X O 41-42 N.C. Trip (Short-Circuit)
      
    ⋆ X = Contact Closed
    O = Contact Open
    ‡ 
    Click to enlarge - 140M-14-15

    Description Connection Diagram⋆  Trip Rating For Use With Cat. No.
    Click to enlarge - 140M-17-1 Undervoltage Trip
  • Left-side mounted

  • Adds 18 mm to the width of the circuit breaker

  • Automatically trips MPCB/MCP when voltage falls below 35…70%
    		•  Click to enlarge - 140M-17-2 24V, 60 Hz 140M-C, D, F; 140U-D 140M-C-UXJ
    24V, 50 Hz 140M-C-UXK
    120V, 60 Hz 140M-C-UXD
    110V, 50 Hz 140M-C-UXC
    208V, 60 Hz 140M-C-UXH
    220…230V, 50 Hz 140M-C-UXF
    240…260V, 60 Hz 140M-C-UXA
    277V, 60 Hz 140M-C-UXT
    380…400V, 50 Hz 140M-C-UXN
    480V, 60 Hz/415V, 50 Hz 140M-C-UXB
    575V, 60 Hz/500V, 50 Hz 140M-C-UXM
    600V, 60 Hz 140M-C-UXVC
    Undervoltage Trip
  • Left-side mounted

  • 2 early make contacts integrated

  • Adds 18 mm to the width of the circuit breaker

  • Automatically trips MPCB/MCP when voltage falls below 35…70%
    		•  Click to enlarge - 140M-C-UC 24V, 60 Hz 140M-C, D, F 140M-C-UCJ
    24V, 50 Hz 140M-C-UCK
    120V, 60 Hz 140M-C-UCD
    110V, 50 Hz 140M-C-UCC
    208V, 60 Hz 140M-C-UCH
    220…230V, 50 Hz 140M-C-UCF
    240…260V, 60 Hz 140M-C-UCA
    277V, 60 Hz 140M-C-UCT
    380…400V, 50 Hz 140M-C-UCN
    480V, 60 Hz/415V, 50 Hz 140M-C-UCB
    575V, 60 Hz/500V, 50 Hz 140M-C-UCM
    600V, 60 Hz 140M-C-UCVC
    Shunt Trip
  • Left-side mounted

  • Adds 18 mm to the width of the circuit breaker

  • Provides remote tripping of the MPCB/MCP
    		•  Click to enlarge - 140M-17-3 24V, 60 Hz 140M-C, D, F; 140U-D 140M-C-SNJ
    24V, 50 Hz 140M-C-SNK
    110V, 50 Hz/120V, 60 Hz 140M-C-SND
    208V, 60 Hz 140M-C-SNH
    220…230V, 50 Hz 140M-C-SNF
    240…260V, 60 Hz 140M-C-SNA
    277V, 60 Hz 140M-C-SNT
    380…400V, 50 Hz 140M-C-SNN
    480V, 60 Hz/415V, 50 Hz 140M-C-SNB
    575V, 60 Hz/500V, 50 Hz 140M-C-SNM
    600V, 60 Hz 140M-C-SNVC
    24V DC 140M-C-SNZJ
    Click to enlarge - 140M-17-4 Undervoltage Trip Unit
  • Internal, front-mounted

  • Integrated short-circuit trip indication

  • Automatically trips MPCB when voltage falls below 35…70%
    		•  Click to enlarge - 140M-17-5 24V, 50/60 Hz 140-CMN 140-CUV-KJ
    110V, 50 Hz/120V, 60 Hz 140-CUV-D
    220V, 50 Hz/240V, 60 Hz 140-CUV-A
    Click to enlarge - 140M-17-6 Shunt Trip Unit
  • Internal, front-mounted

  • Integrated short-circuit trip indication

  • Provides remote tripping of the MPCB
    		•  Click to enlarge - 140M-17-7 24V, 50/60 Hz 140-CMN 140-CRT-KJ
    110V, 50 Hz/120V, 60 Hz 140-CRT-D
    220V, 50 Hz/240V, 60 Hz 140-CRT-A
      
    ⋆ 
    Click to enlarge - 140M-14-15

    Description For Use With Cat. No.
    Click to enlarge - 140M-18-1 Anti-Tamper Shield
    Provides protection against inadvertent adjustment of the current setting     		10 pcs/pkg 140M-C, D, F 140M-C-CA
    Click to enlarge - 140M-C-KRY1_L Lockable Twist Knob
  • For one padlock 5 mm (3/16 in.) Æ shackle

  • Can be locked in OFF position
    		•  Black 140M-C, D, F; 140U-D 140M-C-KN1
    Red/Yellow 140M-C-KRY1
    Click to enlarge - 140M-C-M3_C Locking Tag
  • Padlock attachment to the lockable handles

  • Up to three padlocks 4…8 mm (5/16 in.) Æ shackle
    		•  140M-C-KN1, 140M-C-KRY1 140M-C-M3
    Click to enlarge - 140M-18-3 Padlockable Operating Knob
  • Accepts 8 mm (5/16 in.) Æ padlock shackle — up to three padlocks

  • Permits padlocking in the off position
    		•  Black 140-CMN 140-KN
    Red/Yellow 140-KRY
    Click to enlarge - 140M-C-DN66_Handle_L Door Coupling Handle
  • For 3 padlocks 4…8 mm (5/16 in.) in diameter

  • IP66 Protection/Type 1, 4, 4X, 12

  • Interlock override capability

  • Can be modified for locking in ON position

  • Ships with coupling — order extension shaft and legend plate separately

  • Mounting depth (front of DIN Rail to front of enclosure door):

    •      - 140M-C: 105.5 mm ± 5 mm (4.15 in. ± 3/16 in.)
         - 140M-D: 114.5 mm ± 5 mm (4.5 in. ± 3/16 in.)
         - 140M-F: 137.1 mm ± 5 mm (5.4 in. ± 3/16 in.)
         - 140-CMN: 169 mm +/- 5 mm (6.7 in. +/- 3/16 in.)
         - 140U-D: 114.5mm +/- 5mm (4.5 in. +/- 3/16 in.) ser E or later handles only     		Black 140M-C, D, F; 140U-D 140M-C-DN66
    140-CMN 140-CDN66
    Click to enlarge - 140M-C-DRY66_Handle_L Red/Yellow 140M-C, D, F; 140U-D 140M-C-DRY66
    140-CMN 140-CDRY66
    Click to enlarge - 140M-18-7 Legend Plate
  • Marking: "Hauptschalter" and "Main Switch"

  • Marking: "Not-Aus" and "Emergency Off"
    		•  140-CDN66 140M-C-DFCN
    140-CDRY66 140M-C-DFCRY
    Click to enlarge - 140M-18-6 Extension Shaft
    Cut to required length for mounting depth (front of DIN Rail to front of enclosure door):
    - 140M-C: 117…338 mm (4.6.…13.3 in.)
    - 140M-D: 126…347 mm (5.0.…13.7 in.)
    - 140M-F: 149…369 mm (5.9.…14.5 in.)
    - 140-CMN: 180…403 mm (7.1.…15.9 in.)
    - 140U-D: 126...347 mm (5.0...13.7 in.) ser E or later handles only     		140M-C-DN66,
    140M-C-DRY66,
    140-CDN66,
    140-CDRY66     		140M-C-DS
    Extension Shaft (Extended Length)
    Cut to required length for mounting depth (front of DIN Rail to front of enclosure door):
    - 140M-C: 117…488 mm (4.6…19.2 in.)
    - 140M-D: 126…497 mm (5.0…19.6 in.)
    - 140M-F: 149…519 mm (5.9…20.4 in.)
    - 140-CMN: 180…553 mm (7.1…21.8 in.)
    - 140U-D: 126...497 mm (5.0...19.6 in.) ser E or later handles only     		140M-C-DN66,
    140M-C-DRY66,
    140-CDN66,
    140-CDRY66     		140M-C-DSL
    Click to enlarge - Screw Coupler
    Included with Cat. Nos. 140M-C-DN66 and 140M-C-DRY66     		140M-C, D, F; 140U-D 140M-C-DNC
    Click to enlarge - 140M-18-9 IP65 Non-Metallic Enclosure
  • Knockouts for M20 and M25 fittings

  • Suitable for flexible cable with internal ground wire or conduit when externally grounded around the outside of the enclosure (no UL/CSA approval)
    		•  Black Handle 140M-C 198E-AYTG2
    Red/Yellow Handle 140M-C 198E-AYTJ2
    Click to enlarge - 140M-18-11 Screw Adapter
  • For screw arrangement of a motor protection circuit breaker
    		•  10 pcs/pkg 140M-C, D, F; 140U-D 140M-C-N45
      

    Description For Use With Cat. No.
    Click to enlarge - 140M-19-1 ECO Connecting Module — 12 A
  • For DOL and reversing starters

  • Eco-starters mount on single DIN Rail (140M on DIN Rail)

  • Electrical and mechanical interconnection of 140M and 100-K contactors
    		•  140M-C to 100-K 140M-C-PEK12
    ECO Connecting Modules — 25 A
  • Eco-starters mount on single DIN Rail (140M on DIN Rail)

  • Electrical and mechanical interconnection of 140M MPCB and 100-C (with AC coils or 24V DC electronic coils) contactors
    		•  140M-C to 100-C09…C23 140M-C-PEC23
    140M-D to 100-C09…C23 140M-D-PEC23
    ECO Connecting Modules — 25 A
  • Eco-starters mount on single DIN Rail (100-C on DIN Rail)

  • Electrical and mechanical interconnection of 140M MPCB and 100-C (with AC or DC coils)
    		•  140M-C, 140M-D to 100-C09…C23 140M-C-PEC23A
    Connecting Modules — 25 and 45 A
  • Contactor and MPCB MUST BE mounted separately on (2) DIN Rails

  • Electrical interconnection of 140M and 100-C (with AC coils)
    		•  140M-C to 100-C09…C23 140M-C-PNC23
    140M-D to 100-C09…C23 140M-D-PNC23
    140M-D to 100-C30…C37 140M-D-PNC37
    140M-F to 100-C30…C37 140M-F-PNC37
    140M-F to 100-C43 140M-F-PNC43
    Coil Modules — 25 A and 45 A
  • For use with Bulletin 103T/107T 3-component starters
    		•  140M-C, -D to 100-C09…C23 140M-C-PSC23
    140M-D, -F to 100-C30…C43 140M-F-PSC43
    Click to enlarge - 140M-19-2 Spacing Adapter
  • Required for self-protected combination motor controller (Type E) applications of Bul. 140M-C, -D, and -F MPCBs. Not for use with bus bars.
    		•  140M-C, -D 140M-C-TE1
    140M-F 140M-F-TE
    Click to enlarge - 140M-C-WBE_L Feeder Block for Compact Busbar
  • Supply of compact busbars

  • Increases terminal capacity
    		•  140M-C 140M-C-WBE
    140M-F 140M-F-WBE
    Click to enlarge - 140M-C-WTN_L Feeder Terminal for Compact Busbar
  • For supply of compact busbars

  • Top feed — overlaps compact busbar

  • Meets IEC spacing requirements
    		•  140M-C, -D 140M-C-WTN
    Click to enlarge - 140M-C-WTEN_L Feeder Terminal for Compact Busbar
  • For supply of compact busbars

  • Top feed — overlaps compact busbar

  • Meets UL Type E spacing requirements
    		•  140M-C, -D 140M-C-WTEN
    140M-F 140M-F-WTE
    Click to enlarge - 140M-C-W453N_L Three-Phase Compact Busbar for 32 A Motor Protection Circuit Breakers — 64 A Max. Continuous Current
  • 45 mm spacing

  • For use with front-mounted auxiliary contact
    		•  2 connections 140M-C, -D 140M-C-W452N
    3 connections 140M-C-W453N
    4 connections 140M-C-W454N
    5 connections 140M-C-W455N
    Click to enlarge - 140M-C-W543N_L Three-Phase Compact Busbar for 32 A Motor Protection Circuit Breakers — 64 A Max. Continuous Current
  • 54 mm spacing

  • For use with side-mounted auxiliary contact
    		•  2 connections 140M-C, -D 140M-C-W542N
    3 connections 140M-C-W543N
    4 connections 140M-C-W544N
    5 connections 140M-C-W545N
    Click to enlarge - 140M-19-6 Three-Phase Compact Busbar for 45 A Motor Protection Circuit Breakers — 115 A Max. Continuous Current
  • 54 mm spacing

  • For use with front-mounted auxiliary contact
    		•  2 connections 140M-F 140M-F-W542
    3 connections 140M-F-W543
    4 connections 140M-F-W544
    Three-Phase Compact Busbar for 45 A Motor Protection Circuit Breakers — 115 A Max. Continuous Current
  • 63 mm spacing

  • For use with side-mounted auxiliary contact
    		•  2 connections 140M-F 140M-F-W632
    3 connections 140M-F-W633
    4 connections 140M-F-W634
    Click to enlarge - 140M-C-WSN_L Terminal Cover
  • For covering of unused compact bus bar terminals

  • IP2X finger protection

  • Must be ordered in multiples of 10
    • (10 pcs/pkg)     		140M-C,
    140M-D     		140M-C-WSN
    140M-F 140M-F-WS
    Click to enlarge - 140M-KBH2_L Top Hat Rail Adpapter — 10 mm
  • Adjusts the depth of the 140M-C to the 140M-D

  • Allows the use of compact busbars accross both frame sizes

  • Must be ordered in multiples of 10
    • (10 pcs/pkg)     		140M-C 140-KBH2
      

    Notes:  1. See Bulletin 140U for Internal and External Accessories for Bulletin 140M-H, J, L and N frames.

     2. Bulletin 140M-I frame Accessories such as auxiliaries, alarms, undervoltage and shunt trips are only available as factory installed modifications. See 140M Factory Modifications (Open).

    Description For Use With Pkg. Quantity Cat. No.
    Click to enlarge - 140U-44-1 Terminal End Cover — 0.25 in. 140M-I 1 140U-I-TC2
    Terminal End Cover — 0.41 in. 140U-I-TC4
    Click to enlarge - ab_cover_006589 Terminal Shields (Plastic)
    IP20 Ingress Protection     		140M-I 1 140U-I-TS1
    Click to enlarge - 140M-20-3 Padlockable Handle Lock Hasp — Off only
    Padlocking Hasp
    Lock-OFF only     		140M-I 1 140U-I-PL
    Click to enlarge - 140M-20-4 End Cap Kit
    Provides 3-phase connections for terminal or bolt-on connections
    Metric Hardware     		140M-I 1 140U-I-ECM
    Click to enlarge - 140M-20-5 Phase Barriers
    Provides additional phase clearance when special connections are required     		140M-I 2 140U-I-PB
    Click to enlarge - 140U-J-TLS1_C Terminal Lugs
    Steel Terminal
    Copper/Aluminum wire
    #14-1/0 AWG     		140M-I 3 140U-I-TLS1
    Terminal Lugs
    Stainless Steel Terminal
    Copper/Aluminum wire
    #4-4/0 AWG     		140U-I-TLS2
    Click to enlarge - 140M-20-2 Rotary Close Couple Handle
    International
    Black handle     		140M-I 1 140U-I-RCB
    Rotary Close Couple Handle
    International
    Red/Yellow handle     		140U-I-RCR
    Click to enlarge - TOC-4_1-6 Operating Mechanism for External Handles 140M-I 1 198-H2
    Click to enlarge - 199H-4_94-2 External Handles      
    Black/Grey
    IP66 (Type 3/3R/4/4X/12)     		140M-I 1 190-HM4
    Red/Yellow
    IP66 (Type 3/3R/4/4X/12)     		190-HM4E
    Black/Grey
    IP55 (Type 1)     		190-HM1
    Red/Yellow
    IP55 (Type 1)     		190-HM1E
    Click to enlarge - 60_125ACombo_006283_bw Overload Pre-trip Auxiliary Contact (AX)
    Opens contactor coil circuit on overload before MPCB trips (Automatic reset)     		140M-J, -L (MPCB only) 1 140U-J-ER1RX
      

    Description For Use With Pkg. Quantity Cat. No.
    Click to enlarge - 199H-4_94-3 Extension Shafts 140M-I 5 194R-R3
    Standard Enclosure Working Depth [mm (in.)]
    Minimum 203 (8)
    Maximum 305 (12)
    Extended 194R-R4
    Minimum 203 (8)
    Maximum 508 (20)
    Click to enlarge - 140M-21-2 Flex-Cable Operating Mechanism
    NEMA Type 1/3/12/4/4X
    Flange-Mount Handle     		3 ft. (0.9 m) Cable 140M-I 1 140U-I-FCX03
    4 ft. (1.2 m) Cable 140U-I-FCX04
    6 ft. (1.9 m) Cable 140U-I-FCX06
    10 ft. (3.0 m) Cable 140U-I-FCX10
    Flex-Cable Operating Mechanism
    Stainless Steel - Type 4/4X
    Flange Mount Handle     		3 ft. (0.9 m) Cable 140U-I-FCS03
    4 ft. (1.2 m) Cable 140U-I-FCS04
    6 ft. (1.9 m) Cable 140U-I-FCS06
    10 ft. (3.0 m) Cable 140U-I-FCS10
    Click to enlarge - 140M-19-7 DIN (#3) symmetrical hat rail
    35 x 7.5 x 1 m     		140M-D
    140M-F
    100-C all     		10 pcs/kg 199-DR1
    Click to enlarge - 140M-19-8 DIN (#3) Symmetrical Rail
    35 mm x 15 mm x 1 m long
    Top Hat Rail (DIN #3 Symmetrical Rail)     		140M-C
    140M-D
    140M-F
    140-CMN     		5 pcs/kg 1492-DR9
      

    Internal Control Modules — Field Installed

      Description Diagram Mounting Location For Use With Cat. No.
    Click to enlarge - 58_125AAux_006287_bw Auxiliary Contact (AX)
    Electrically indicates "ON/OFF" status of breakers     		(1) 1a-1b Click to enlarge - 140U-43-3 Click to enlarge - 140U-51-2 140M-H, -J, -L 140U-H-EA1
    140M-N 140U-N-EA1
    (2) 1a-1b 140M-H, -J, -L 140U-H-EA2
    Left AND Right side 140M-N 140U-N-EA2
    (1) 1a-1b Click to enlarge - 140U-43-2 140M-I (Note: adding this part in the field voids UL/CSA on the MPCB) 140U-I-EA1RX
    Right side only
    Alarm Contact (AL)
    Electrically indicates when the breaker is in the "TRIPPED" state     		(1) 1M (make)-1B (break) Click to enlarge - 140U-43-5 Click to enlarge - 140U-43-2 140M-H 140U-H-ER1
    140M-J, -L 140U-J-ER1
    Right side ONLY 140M-N 140U-N-ER1
    Click to enlarge - 140U-43-10 140M-I (Note: adding this part in the field voids UL/CSA on the MPCB) 140U-I-ER1LX
    Left side ONLY
    Click to enlarge - 60_125ACombo_006283 Auxiliary/Alarm Contact (AX/AL)
    Combination
    Combination of auxiliary contact and alarm contact     		(1) 1a-1b
    (1) 1M (make)-1B (break)     		Click to enlarge - 140U-43-8 Click to enlarge - 140U-43-2 140M-H 140U-H-EA1R1
    140M-J, -L 140U-J-EA1R1
    Right side only 140M-N 140U-N-EA1R1
    Click to enlarge - 60_125ACombo_006283 Overload Pre-trip Auxiliary Contact (AX)
    Opens contactor coil circuit on overload before MPCB trips (Automatic reset)     		(1) 1a-1b   Click to enlarge - 140U-43-2 140M-J, -L (MPCB only) 140U-J-ER1RX
    Right side only
    Click to enlarge - 140U-51-9 Shunt Trip (SNT)
    Provides remote tripping of the circuit breaker
    Undervoltage trip not available when shunt trip is used     		24…60 V, 50/60/DC Click to enlarge - 140U-43-11 Click to enlarge - 140U-43-10 140M-H, -J, -L 140U-H-SNJ
    12…24V, 50/60/DC 140M-N 140U-N-SNJ
    110…240V, 50/60/DC 140M-H, -J, -L 140U-H-SND
    110…240V AC 140M-N 140U-N-SND
    380…440V AC, 220…250V DC 140M-H, -J, -L 140U-H-SNN
    380…440V AC, 220…250V DC 140M-N 140U-N-SNN
    380…600V, 50/60 Hz Left side ONLY 140M-H, -J, -L 140U-H-SNB
    480…600V, 50/60 Hz 140M-N 140U-N-SNB
    Undervoltage Release (UVT)
    Automatically trips breaker when voltage falls between preset value, 35…70%
    Shunt trip is not available when undervoltage release is used     		24V, 50/60Hz AC; 24V DC Click to enlarge - 140U-43-13 Click to enlarge - 140U-43-10 140M-H, -J, -L 140U-H-UJ
    24V, 50/60 Hz 140M-N 140U-N-UJ
    110…127V, 50/60 Hz 140M-H, -J, -L 140U-H-UD
    140M-N 140U-N-UD
    208…240V, 50/60 Hz 140M-H, -J, -L 140U-H-UA
    140M-N 140U-N-UA
    380…500V, 50/60 Hz 140M-H, -J, -L 140U-H-UB
    Left side ONLY 140M-N 140U-N-UB
    525…600V, 50/60 Hz 140M-H, -J, -L 140U-H-UC
      

      Description For Use With Cat. No.
    Click to enlarge - 140U-44-1 Terminal End Cover
    6.4 mm (0.25 in.) diameter cable entry     		140M-H 140U-H-TC2
    140M-I 140U-I-TC2
    Terminal End Cover
    10.4 mm (0.41 in.) diameter cable entry     		140M-H 140U-H-TC4
    140M-I 140U-I-TC4
    Click to enlarge - ab_cover_006589_bw Terminal Shields
    IP20 Ingress Protection Rating     		140M-H 140U-H-TS
    140M-I 140U-I-TS1
    140M-J 140U-J-TS
    140M-L 140U-L-TS
    Click to enlarge - ab_140U_H_005818_bw Flex-Cable Operating Mechanism
    Includes handle, cable, operating, and bail mechanism
    Pre-assembled and adjusted
    Non-Metallic - UL IP66, Type 1/3/12/4/4X
    Flange Mount Operating Handle     		3 ft (0.9 m) Cable 140M-H 140U-H-FCX03
    4 ft (1.3 m) Cable 140U-H-FCX04
    6 ft (1.8 m) Cable 140U-H-FCX06
    10 ft (3.0 m) Cable 140U-H-FCX10
    3 ft. (0.9 m) Cable 140M-I 140U-I-FCX03
    4 ft. (1.2 m) Cable 140U-I-FCX04
    6 ft. (1.9 m) Cable 140U-I-FCX06
    10 ft. (3.0 m) Cable 140U-I-FCX10
    3 ft (0.9 m) Cable 140M-J 140U-J-FCX03
    4 ft (1.3 m) Cable 140U-J-FCX04
    6 ft (1.8 m) Cable 140U-J-FCX06
    10 ft (3.0 m) Cable 140U-J-FCX10
    4 ft (1.2 m) Cable 140M-L 140U-L-FCX04
    6 ft (1.9 m) Cable 140U-L-FCX06
    10 ft (3.0 m) Cable 140U-L-FCX10
    4 ft. (1.2 m) Cable 140M-N 140U-N-FCX04
    6 ft. (1.9 m) Cable 140U-N-FCX06
    10 ft. (3.0 m) Cable 140U-N-FCX10
    Flex-Cable Operating Mechanism
    Includes handle, cable, operating, and bail mechanism
    Pre-assembled and adjusted
    Stainless Steel - Type 4/4X
    Flange Mount Operating Handle     		3 ft (0.9 m) Cable 140M-H 140U-H-FCS03
    4 ft (1.3 m) Cable 140U-H-FCS04
    6 ft (1.8 m) Cable 140U-H-FCS06
    10 ft (3.0 m) Cable 140U-H-FCS10
    3 ft. (0.9 m) Cable 140M-I 140U-I-FCS03
    4 ft. (1.2 m) Cable 140U-I-FCS04
    6 ft. (1.9 m) Cable 140U-I-FCS06
    10 ft. (3.0 m) Cable 140U-I-FCS10
    3 ft (0.9 m) Cable 140M-J 140U-J-FCS03
    4 ft (1.3 m) Cable 140U-J-FCS04
    6 ft (1.8 m) Cable 140U-J-FCS06
    10 ft (3.0 m) Cable 140U-J-FCS10
    4 ft (1.2 m) Cable 140M-L 140U-L-FCS04
    6 ft (1.9 m) Cable 140U-L-FCS06
    10 ft (3.0 m) Cable 140U-L-FCS10
      

      Description For Use With Cat. No.
    Click to enlarge - 140U-H-RVM12R_C_bw Rotary, Variable-Depth Operating Mechanism
    Rotary handle - IP66, UL Type 3/12/4/4X
    12 in. (30.48 cm) operating rod     		Black Handle 140M-H 140U-H-RVM12B
    Red/Yellow Handle 140U-H-RVM12R
    Black Handle 140M-J 140U-J-RVM12B
    Red/Yellow Handle 140U-J-RVM12R
    Black Handle 140M-L 140U-L-RVM12B
    Red/Yellow Handle 140U-L-RVM12R
    Black Handle 140M-N 140U-N-RM12B
    Rotary, Variable-Depth Operating Mechanism
    UL Type 3/12/4/4X, IP 66 Rotary handle
    21 in. (53.34 cm) operating rod     		Black Handle 140M-H 140U-H-RVM21B
    Red/Yellow Handle 140U-H-RVM21R
    Black Handle 140M-J 140U-J-RVM21B
    Red/Yellow Handle 140U-J-RVM21R
    Black Handle 140M-L 140U-L-RVM21B
    Red/Yellow Handle 140U-L-RVM21R
    Click to enlarge - NFPA_lockout sml_bw Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
    External Type 3/4/4X/12 IP66 Rotary Handle
    12 in. (30.48 cm) operating rod     		Black Handle 140M-H 140U-H-NVM12B
    Red/Yellow Handle 140U-H-NVM12R
    Black Handle 140M-J 140U-J-NVM12B
    Red/Yellow Handle 140U-J-NVM12R
    Black Handle 140M-L 140U-L-NVM12B
    Red/Yellow Handle 140U-L-NVM12R
    Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
    External Type 3/4/4X/12 IP66 Rotary Handle
    21 in. (53.34 cm) operating rod     		Black Handle 140M-H 140U-H-NVM21B
    Red/Yellow Handle 140U-H-NVM21R
    Black Handle 140M-J 140U-J-NVM21B
    Red/Yellow Handle 140U-J-NVM21R
    Black Handle 140M-L 140U-L-NVM21B
    Red/Yellow Handle 140U-L-NVM21R
      

      Description For Use With Cat. No.
    Click to enlarge - TOC-4_1-6 Operating Mechanism for External Handles 140M-I 198-H2
    Click to enlarge - 194R-HM4-N3_L External Operating Handle Black/Grey Handle
    IP66 (Type 3/3R/4/4X/12)     		140M-I 190-HM4
    Red/Yellow Handle
    IP66 (Type 3/3R/4/4X/12)     		190-HM4E
    Black/Grey Handle
    IP55 (Type 1)     		190-HM1
    Red/Yellow Handle
    IP55 (Type 1)     		190-HM1E
    Click to enlarge - 199H-4_94-3 Extension Shaft
    Standard length — Enclosure Working Depth
  • Minimum: 8 in. (203 mm)
    Maximum: 12 in (305 mm)
    		•  140M-I 194R-R3
    Extension Shaft
    Extended length — Enclosure Working Depth
  • Minimum: 8 in. (203 mm)
    Maximum: 20 in (508 mm)
    		•  194R-R4
    Click to enlarge - motor_operator_sml_bw Motor Operator
    Remotely opens, closes, and resets the MPCB or MCP     		For use with 3- or 4-pole MCCBs, 110…240V AC/DC 140M-H 140U-H-EOPD
    For use with 3- or 4-pole MCCBs, 24V DC 140U-H-EOPZ
    For use with 3- or 4-pole MCCBs, 110…240V AC/DC 140M-J 140U-J-EOPD
    For use with 3- or 4-pole MCCBs, 24V DC 140U-J-EOPZ
    For use with 3- or 4-pole MCCBs, 110…240V AC/DC 140M-L 140U-L-EOPD
    For use with 3- or 4-pole MCCBs, 24V DC 140U-L-EOPZ
    For use with 3- or 4-Pole MCCBs, 110…240V AC/DC 140M-N 140U-N-EOPD
    For use with 3- or 4-Pole MCCBs, 230…240V AC/DC 140U-N-EOPA
    For use with 3- or 4-Pole MCCBs, 24V DC 140U-N-EOPZ
    Click to enlarge - 140U-H-RCB_L Rotary, Direct Couple Operating
    Mechanism
    Rotary handle - IP42 UL Type 1
    Breaker mounted     		Black Handle 140M-H 140U-H-RCB
    Black Handle 140U-H-RCB
    Black Handle 140M-I 140U-I-RCB
    Red/Yellow Handle 140U-I-RCR
    Black Handle 140M-J 140U-J-RCB
    Red/Yellow Handle 140U-J-RCR
    For use with 3- or 4-pole MCCBs 140M-L 140U-L-RMX
    Click to enlarge - 140U-H-ECM_C End Cap Kit
    Provides three-phase connections for terminal or bolt-on connections
    Metric hardware provided     		140M-H 140U-H-ECM
    140M-I 140U-I-ECM
    140M-J 140U-J-ECM
    140M-L 140U-L-ECM
    Click to enlarge - 140U-H-PL_C Padlock Kit
    Padlocking hasp
    Lock-OFF only     		140M-H 140U-H-PL
    140M-I 140U-I-PL
    140M-J 140U-J-PL
    140M-N 140U-N-PL
    Click to enlarge - 140U-H-DRA_C DIN Rail Adapter
    Allows MCCB to mount to 35 mm DIN Rail     		140M-H 140U-H-DRA
    Click to enlarge - 140U-H-PB_C Phase Barriers
    Provides additional phase clearance when special connections that extend past the circuit breaker housing are required     		Qty: 2 140M-H 140U-H-PB
    140M-I 140U-I-PB
    140M-J 140U-J-PB
    140M-L 140U-K-PB
    140M-N 140U-N-PB
    Click to enlarge - 140_BASE_R-cmyk Plug-in Base Adapters
    Plug-in provides power terminations and adapter for applications where the ability to quickly remove or replace the circuit breakers is required     		140M-H 140U-H-PAD3
    Plug-in Base Auxiliary Contacts
    Provides auxiliary contact functions to detect breaker installation status     		140M-H 140U-H-PDK
    Click to enlarge - 140U-J-MHM_bw Replacement Mounting Hardware (4) M4 - 0.7 x 75 mm 140M-H 140U-H-MHM
    Replacement Mounting Hardware (4) M4 - 0.7 x 90 mm 140M-J 140U-J-MHM
    Replacement Mounting Hardware (4) M5 - 0.8 x 100 mm 140M-L 140U-L-MHM
    Replacement Mounting Hardware (4) M8 - 1 x 35 mm 140M-N 140U-N-MHM
      

    Terminal Lugs

      Description Frame Size Cat. No.
    Click to enlarge - 140U_K_TLA1A_right Terminal Lugs Steel Terminal
    Copper/Aluminum wire
    #14-1/0 AWG     		Qty: 3 I 140U-I-TLS1
    Stainless Steel Terminal
    Copper/Aluminum wire
    #4-4/0 AWG     		Qty: 3 I 140U-I-TLS2
    Click to enlarge - 140U-J-TLS1_C Terminal Lugs Aluminum lugs, Al or Cu wire
    (1) 4…350 MCM
    or (1) 25…185 mm2     		Qty: 1 J 140U-J-TLA1
    Stainless steel box lugs,
    Cu wire only
    (1) 4…350 MCM
    or (1) 25…185 mm2     		Qty: 1 J 140U-J-TLS1
    Click to enlarge - 140U-L-TL6C1_r Terminal Lugs Aluminum lug, Al or Cu wire
    (1) 2…500 MCM
    or (1) 35…240 mm2     		Qty: 1 L 140U-L-TL4A1
    Copper lug, Cu wire only
    (1) 2…500 MCM
    or (1) 35…240 mm2     		Qty: 1 140U-L-TL4C1
    Aluminum lug, Al or Cu wire
    (1) 500…750 MCM
    or (1) 240…380 mm2     		Qty: 3 (includes shield) 140U-L-TL6A1
    Copper lug, Cu wire only
    (1) 500…750 MCM
    or (1) 240…380 mm2     		Qty: 3 (includes shield) 140U-L-TL6C1
    Click to enlarge - 140U-L-TL6A2_r Terminal Lugs Aluminum lug, Al or Cu wire
    (2) 2…500 MCM
    or (2) 35…240 mm2     		Qty: 3 (includes shield) L 140U-L-TL6A2
    Copper lug, Cu wire only
    (2) 2…500 MCM
    or (2) 35…240 mm2     		Qty: 3 (includes shield) 140U-L-TL6C2
      

    Terminal Lugs, Continued

      Description Frame Size Cat. No.
    Click to enlarge - 140U_N_TLA3_right Terminal Lugs Aluminum lug, Al or Cu wire
    (2) 1…500 MCM
    or (2) 50…240 mm2     		Qty: 1 N 140U-N-TLA2
    Aluminum lug, Al or Cu wire
    (3) 3/0…400 MCM
    or (3) 95…185 mm2     		Qty: 1 N 140U-N-TLA3
    Aluminum lug, Al or Cu wire
    (4) 4/0…500 MCM
    or (4) 120…300 mm2     		Qty: 1 N 140U-N-TLA4
    Aluminum lug, Al or Cu wire
    (3) 500…750 MCM
    or (3) 300…400 mm2     		Qty: 1 N 140U-N-TLA3A
    Copper lug, Cu wire only
    (2) 2/0…500 MCM
    or (2) 70…240 mm2     		Qty: 1 N 140U-N-TLC2
    Copper lug, Cu wire only
    (3) 3/0…500 MCM
    or (3) 95…240 mm2     		Qty: 1 140U-N-TLC3
    Copper lug, Cu wire only
    (4) 3/0…400 MCM
    or (4) 95…185 mm2     		Qty: 1 140U-N-TLC4
      

    140M Factory Modifications (Open)

    Note: For modifications add (option code _) for desired features to cat. no. Available in North America only.

    f
    Miscellaneous
    Code Description Frame Size
    KN(1) Black Lockable Knob C, D, F, CMN
    KRY(1) Red/Yellow Lockable Knob C, D, F, CMN
    TE(1) Spacing Adapter for Self-Protected Starters (Type E) C, D, F
    MT STD Bus Bar Mount, Top C, D, F, H, CMN
    MU STD Bus Bar Mount, Universal J, K, L

    g
    Aux / Trip Contacts - C, D, F
    1st Code Description 2nd Code Description
    Bottom Front Right Side
    X Placeholder X Placeholder
    A 1 N.C. C 1 N.O. + 1 N.C.
    B 1 N.O. D 2 N.O.
    C 1 N.O. + 1 N.C. E 2 N.C.
    D 2 N.O. K 1 N.C. (SC+OL) + 1 N.C. (SC)
    E 2 N.C. L 1 N.O. (SC+OL) + 1 N.O. (SC)
    R 1 N.C. + 1 N.O. (SC+OL) M 1 N.C. (SC+OL) + 1 N.O. (SC)
    S 1 N.O. + 1 N.O. (SC+OL) N 1 N.O. (SC+OL) + 1 N.C. (SC)
        Q 1 N.O. (SC) + 1 N.C. (SC)

    g
    Aux / Trip Contacts - CMN
    1st Code Description 2nd Code Description
    Bottom Front Top Front§ 
    X Placeholder X Placeholder
    C 1 N.O. + 1 N.C. K 1 N.C. (OL) + 1 N.C. (SC)
    D 2 N.O. L 1 N.O. (OL) + 1 NO (SC)
    E 2 N.C. M 1 N.C. (OL) + 1 N.O. (SC)
        N 1 N.O. (OL) + 1 N.C. (SC)
      

    § Cannot be combined with option "h".


    g
    Aux / Trip Contacts - H, J, L
    1st Code Description 2nd Code Description
    Bottom Front Right Side
    X Placeholder X Placeholder
    C 1 N.O. + 1 N.C.
    R‡  1 N.O. + 1 N.C. (Overload Function)
    F⋆  2 N.O. + 2 N.C.
    N⋆  1 N.O. (SC+OL) + 1 N.C. (SC)
    T⋆  1 N.O. + 1 N.C. and 1 N.O. + 1 N.C. (SC+OL)

    ⋆ Only available on MCPs.
    ‡ J- and L-Frame MPCB only.


    g
    Aux / Trip Contacts - I, N
    1st Code Description 2nd Code Description
    Left Side Right Side
    X Placeholder X Placeholder
    C 1 N.O. + 1 N.C. C 1 N.O. + 1 N.C.
    F 2 N.O. + 2 N.C. F⋆  2 N.O. + 2 N.C.
    N 1 N.O. (SC+OL) + 1 N.C. (SC) N⋆  1 N.O. (SC+OL) + 1 N.C. (SC)
    T 1 N.O. + 1 N.C. and 1 N.O. + 1 N.C. (SC+OL) T⋆  1 N.O. + 1 N.C. and 1 N.O. + 1 N.C. (SC+OL)

    ⋆ Only available on MCPs.


    140M Factory Modifications (Open), Continued

    Note: For modifications add (option code *) for desired features to cat. no. Available in North America only.

    h
    UV and Shunt Trips - C, D, F
    1st Code Description 2nd Code Description
    Left Side Voltage
    G Undervoltage Trip J 24V AC, 60 Hz
    P Shunt Trip K 24V AC, 50 Hz
    D 120V AC, 60 Hz
    C 110V AC, 50 Hz
    H 208V AC, 60 Hz
    F 220…230V AC, 50 Hz
    A 240V AC, 60 Hz
    T 277V AC, 60 Hz
    N 380…400V AC, 50 Hz
    B 480V AC, 60 Hz and 415V AC, 50 Hz
    VC 600V AC, 60 Hz
    M 575V AC, 60 Hz and 500V AC, 50 Hz
    ZR 9V DC
    ZQ 12V DC
    ZJ 24V DC
    ZW 36V DC
    ZY 48V DC
    ZZ 60V DC
    ZB 64V DC
    ZG 72V DC
    ZE 80V DC

    h
    UV and Shunt Trips - CMN
    1st Code Description 2nd Code Description
    Top Front§  Voltage
    G Undervoltage Trip KJ 24V AC, 60 Hz and 24V AC, 50 Hz
    P Shunt Trip D 120V AC, 60 Hz and 110V AC, 50 Hz
    A 240V AC, 60 Hz and 220…230V AC, 50 Hz
      

    h
    UV and Shunt Trips - H, J, L
    1st Code Description 2nd Code Description
    Left Front UV Voltage
    G Undervoltage Trip J 24V AC/DC
    D 110…127V AC
    A 208…240V AC
    B 380…500V AC
    C 525…600V AC
    Left Front Shunt Voltage
    P Shunt Trip J 12…60V AC/DC
    D 110…240V AC/DC
    B 380…600V AC

    h
    UV and Shunt Trips - I
    1st Code Description 2nd Code Description
    Left Front UV Voltage
    G Undervoltage Trip J 24V AC
    D 110…127V AC
    A 208…240V AC
    B 380…480V AC
    Left Front Shunt Voltage
    P Shunt Trip J 12…24V AC/DC
    D 48…127V AC and 48…60V DC
    N 208…380V AC and 110…127V DC
    B 415…600V AC and 220…250V DC

    h
    UV and Shunt Trips - N
    1st Code Description 2nd Code Description
    Left Front UV Voltage
    G Undervoltage Trip J 24V AC
    D 110…127V AC
    A 208…240V AC
    B 380…480V AC
    Left Front Shunt Voltage
    P Shunt Trip J 12…24V AC/DC
    D 110…240V AC and 110…125V DC
    N 380…440V AC and 220…250V DC
    B 480…600V AC

    Specifications

    IEC Performance Data

      Cat. No. 140M-C2E-
    A16 A25 A40 A63 B10 B16 B25 B40 B63 C10 C16 C20 C25 C29 C32
    Rated Operational Current, Ie [A] 0.16 0.25 0.4 0.63 1 1.6 2.5 4 6.3 10 16 20 25 29 32
    Magnetic Release Current [A] 2.1 3.3 5.2 8.2 13 21 33 52 82 130 208 260 325 406 448
    Switching of Standard Three-Phase Motors
    AC-3
    230/240V [kW] — — 0.06 0.09 0.18 0.25 0.37 0.75 1.5 2.2 4.0 5.5 5.5 7.5 7.5
    400/415V [kW] 0.02 0.04 0.09 0.18 0.25 0.55 0.75 1.5 2.2 4.0 7.5 10 11 13 15
    500V [kW] 0.06 0.09 0.12 0.18 0.37 0.75 1.1 2.2 3.0 6.3 10 11 15 18.5 20
    690V [kW] 0.06 0.09 0.18 0.25 0.55 1.1 1.8 3.0 4.0 7.5 13 17 22 25 25
    Back-Up Fuses
    gG, gL, only if Icc³Icu
    230/240V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  100 100 125 125
    400/415V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  80 100 100 125 125
    440/460V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  63 80 80 80 100 100
    500V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  80 80 80 80 100 100
    690V [A] ⋆  ⋆  ⋆  ⋆  ⋆  16 20 35 50 50 63 63 63 80 80
    Ultimate Short Circuit Breaking Capacity
    Icu
    230/240V [kA] 100 100 100 100 100 100 100 100 100 100 100 65 65 50 50
    400/415V [kA] 100 100 100 100 100 100 100 100 100 100 65 50 15 15 15
    440/460V [kA] 100 100 100 100 100 100 100 100 100 50 10 6 6 6 6
    500V [kA] 100 100 100 100 100 100 100 100 100 50 10 6 6 6 6
    690V [kA] 100 100 100 100 100 8 8 8 4 4 3 3 3 3 3
    Rated Service Short Circuit Breaking Capacity
    Ics
    230/240V [kA] 100 100 100 100 100 100 100 100 100 100 100 50 50 25 25
    400/415V [kA] 100 100 100 100 100 100 100 100 100 100 50 15 15 15 15
    440/460V [kA] 100 100 100 100 100 100 100 100 100 50 6 6 6 6 6
    500V [kA] 100 100 100 100 100 100 100 100 100 50 6 6 6 6 6
    690V [kA] 100 100 100 100 100 8 8 8 4 4 3 3 3 3 3
      
    ⋆ No back-up fuse required.

      Cat. No. 140M-D8E- Cat. No. 140M-F8E-
    B25 B40 B63 C10 C16 C20 C25 C29 C32 C10 C16 C20 C25 C32 C45
    Rated Operational Current, Ie [A] 2.5 4.0 6.3 10 16 20 25 29 32 10 16 20 25 32 45
    Magnetic Release Current [A] 33 52 82 130 208 260 325 406 448 130 208 260 325 416 585
    Switching of Standard Three-Phase Motors
    AC-3
    230/240V [kW] 0.37 0.75 1.5 2.2 4.0 5.5 5.5 7.5 7.5 2.2 4.0 5.5 6.3 7.5 13
    400/415V [kW] 0.75 1.5 2.2 4.0 7.5 10 11 13 15 4.0 7.5 10 11 15 22
    500V [kW] 1.1 2.2 3.0 6.3 10 11 15 18.5 20 6.3 10 11 15 20 30
    690V [kW] 1.8 3.0 4.0 7.5 13 17 22 25 25 7.5 13 17 22 30 40
    Back-Up Fuses
    gG, gL, only if Icc³Icu
    230/240V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆ 
    400/415V [A] ⋆  ⋆  ⋆  ⋆  ⋆  100 100 125 125 80 100 100 100 125 125
    440/460V [A] ⋆  ⋆  ⋆  ⋆  80 100 100 125 125 80 100 100 100 125 125
    500V [A] ⋆  ⋆  ⋆  ⋆  80 80 80 100 100 80 100 100 100 125 125
    690V [A] 20 35 50 50 63 63 63 80 80 63 80 80 80 100 100
    Ultimate Short Circuit Breaking Capacity
    Icu
    230/240V [kA] 100 100 100 100 100 100 100 65 65 100 100 100 100 100 100
    400/415V [kA] 100 100 100 100 100 100 65 50 50 100 100 100 100 65 65
    440/460V [kA] 100 100 100 100 50 50 50 25 25 65 65 65 65 65 50
    500V [kA] 100 100 100 100 50 50 50 25 25 50 50 50 50 50 50
    690V [kA] 10 10 10 6 6 6 6 6 6 10 10 10 10 10 10
    Rated Service Short Circuit Breaking Capacity
    Ics
    230/240V [kA] 100 100 100 100 100 100 100 50 50 100 100 100 100 100 100
    400/415V [kA] 100 100 100 100 50 25 25 25 25 50 50 50 50 50 50
    440/460V [kA] 100 100 100 100 50 25 25 20 20 50 50 50 50 50 50
    500V [kA] 100 100 100 100 50 25 25 20 20 50 50 50 50 50 50
    690V [kA] 10 10 10 6 4 4 4 4 4 10 10 10 10 6 6
      
    ⋆ No back-up fuse required.

    Cat. No. 140-CMN-…
    -2500 -4000 -6300 -9000
    Rated Operational Current, Ie [A] 25 40 63 90
    Magnetic Release Current [A] 350 560 890 1260
    Switching of Standard Three-Phase Motors
    AC-3
    230/240V‡  [kW] 5.5/7.5 10/11 13/20 22/25
    400/415V‡  [kW] 7.5/13 15/22 25/32 37/45
    500V‡  [kW] 11/15 18.5/25 30/40 45/55
    690V‡  [kW] 15/22 25/30 37/55 63/75
    Back-up fuses
    gG, gL,, only if Icc ³ Icu
    230/240V [A] ⋆  ⋆  ⋆  ⋆ 
    400/415V [A] 160 160 160 160
    500V [A] 160 160 160 160
    690V [A] 160 160 160 160
    Ultimate short-circuit breaking capacity Icu
    230/240V [kA] 100 100 100 100
    400/415V [kA] 65 65 65 50
    500V [kA] 50 30 30 25
    690V [kA] 15 8 8 6
    Rated service short-circuit breaking capacity Ics
    230/240V [kA] 100 100 100 100
    400/415V [kA] 65 50 50 25
    500V [kA] 50 25 25 13
    690V [kA] 15 8 6 6
      
    ⋆ No back-up fuse required.
    ‡ Power ratings: Preferred values according to IEC 60072-1.

    IEC Performance Data, Continued

      Cat. No. 140M-C2N-
    A16 A25 A40 A63 B10 B16 B25
    Rated Operational Current, Ie [A] 0.16 0.25 0.4 0.63 1 1.6 2.5
    Magnetic Release Current [A] 2.1 3.3 5.2 8.2 13 21 32
    Switching of Standard Three-Phase Motors
    AC-3
    230/240V [kW] — — 0.06 0.09 0.18 0.25 0.37
    400/415V [kW] 0.02 0.04 0.09 0.18 0.25 0.55 0.75
    500V [kW] 0.06 0.09 0.12 0.18 0.37 0.75 1.1
    690V [kW] 0.06 0.09 0.18 0.25 0.55 1.1 1.8
    Back-Up Fuses
    gG, gL, only if Icc³Icu⋆ 
    230/240V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆ 
    400/415V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆ 
    440/460V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆ 
    500V [A] ⋆  ⋆  ⋆  ⋆  ⋆  ⋆  ⋆ 
    690V [A] ⋆  ⋆  ⋆  ⋆  ⋆  16 20
    Ultimate Short Circuit Breaking Capacity
    Icu
    230/240V [kA] 100 100 100 100 100 100 100
    400/415V [kA] 100 100 100 100 100 100 100
    440/460V [kA] 100 100 100 100 100 100 100
    500V [kA] 100 100 100 100 100 100 100
    690V [kA] 100 100 100 100 100 10 8
    Rated Service Short Circuit Breaking Capacity
    Ics
    230/240V [kA] 100 100 100 100 100 100 100
    400/415V [kA] 100 100 100 100 100 100 100
    440/460V [kA] 100 100 100 100 100 100 100
    500V [kA] 100 100 100 100 100 100 100
    690V [kA] 100 100 100 100 100