Bulletin 284 ArmorStart Distributed Motor Controller

Product Overview

Bulletin 284 ArmorStart Distributed Motor Controller

• On-Machine starting solution
  
• Variable frequency AC drive using PowerFlex^® technology
  
• Horsepower range 0.5…5 Hp (0.4…3.3 kW)
  
• Robust IP67/NEMA Type 4 or NEMA Type 4X enclosure rating
  
• Quick disconnect for I/O, communications, motor, three-phase, and control power connections
  
• LED status indication
  
• EtherNet/IP, DeviceNet, and ControlNet communications
  
• Local logic technology using DeviceLogix
  
• Peer-to-peer communications (ZIP) (not available with EtherNet/IP communications)
  
• Connectivity to ArmorPoint distributed I/O products
  
• Factory installed options:
  
  • EMI filter
    
  • Control brake contactor
    
  • Dynamic brake connector
    
  • Source brake contactor
    
  • Output contactor
    
  • Shielded motor cable
    
  • 0…10V analog input
    
  • Safety monitor
    
  • Hand/Off/Auto (HOA) with jog
    

Standards Compliance and Certifications

Standards Compliance

UL 508C
CSA C22.2, No. 14
EN/IEC 60947-4-2, EN 50178, EN 61800-3
CE Marked per Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC
CCC
ODVA for EtherNet/IP and DeviceNet

Certifications

cULus (File No. E207834, Guide NMMS, NMMS7)

Mode of Operation

Sensorless Vector Performance (SVP) - V/Hz

This method provides excellent speed regulation and high levels of torque across the entire speed range of the drive, and improved speed regulation even as loading increases. Basic control yields the most cost-effective performance when sensorless vector control is not required.

Automatically provides auto boost (IR compensation) and slip compensation.

Sensorless Vector Control (SVC)

Sensorless vector control provides exceptional speed regulation and very high levels of torque across the entire speed range of the drive.

The Autotune feature allows the Bulletin 284 (SVC) to adapt to individual motor characteristics.

Timer, Counter, Basic Logic and StepLogic™ functions can reduce hardware design costs and simplify control schemes.

Develops high torque over a wide speed range and adapts to individual motor characteristics.

Additional Features

• Eight Preset Speeds
  
• Process Control Loop (PID)
  
• Skip Frequency
  
• Step Logic Functionality
  
• Flying Start
  
• Timer/Counter Functions
  Auto Restart  

Overload Protection

The Bulletin 284 ArmorStart Distributed Motor Controller incorporates, as standard, electronic motor overload protection. This overload protection is accomplished electronically with an I²_t algorithm. The ArmorStart’s overload protection is programmable via the communication network providing the user with flexibility. The overload trip class allows for class 10 overload protection. Ambient insensitivity is inherent in the electronic design of the overload.

Fault Diagnostics

Fault diagnostics capabilities built into the Bulletin 284 ArmorStart Distributed Motor Controller help you pinpoint a problem for easy troubleshooting and quick re-starting.

• Short Circuit
  
• Overtemperature
  
• Overload
  
• Output Fuse Protection
  
• Phase Short
  
• Brake Fuse Protection
  
• Ground Fault
  
• Internal Communication Fault
  
• Stall
  
• DC Bus Fault
  
• Control Power Loss
  
• EEPROM Fault
  
• Control Power Fuse Protection
  
• Hardware Fault
  
• I/O Fault
  
• Restart Retries
  
• Overcurrent
  
• Miscellaneous Fault
  
• DeviceNet Power Loss
  

• Overtemperature
  
• Output Fuse Protection
  
• DeviceNet Power Loss
  
• Internal Communication Fault
  
• DC Bus Fault
  
• EEPROM Fault
  
• Hardware Fault
  
• Restart Retries
  
• Miscellaneous Fault
  

Local Logic via DeviceLogix

Provides local control over the device’s discrete and network I/O. DeviceLogix consists of function blocks, inputs, outputs, and actual hardware data, including fault and status bits.

Factory-Installed Options

HOA Selector Keypad with Jog Function

The HOA Selector Keypad with Jog Function allows for local start/stop control with capabilities to JOG and to Forward/Reverse motor direction.

EMI Filter

The EMI Filter is required to be CE compliant. When selected, a 3–meter shielded 4–conductor motor cordset is provided as standard. This is only available with sensorless vector control.

Control Brake Connector

An internal contactor is used to switch an electromechanical motor brake On/Off. The motor brake is powered from the control power circuit. The configuration of the R1 relay controls the function of the brake. A customer accessible 3 A fuse is provided to protect the brake cable. Included is a 3-meter 3-pin cordset for connection to the motor brake as standard.

Source Brake Contactor

An internal contactor is used to switch an electromechanical motor brake On/Off. The motor brake is powered from the line power circuit. The configuration of the R1 relay controls the function of the brake. A customer accessible 3 A fuse is provided to protect the brake cable. Included is a 3-meter 3-pin cordset for connection to the motor brake as standard.

Shielded Motor Cable

A 3-meter shielded 4-conductor cordset is provided instead of the 3-meter unshielded 4-conductor cordset, when the EMI Filter is selected.

IP67 Dynamic Brake Connector

The IP67 Dynamic Brake Resistor design offers simplicity in wiring and installation. The DB1 option must be selected in order to have the quick disconnect connectivity. See accessories for available IP67 Dynamic Brake Resistors.

Output Contactor

An internal contactor is sourced from control voltage to isolate the load side of the VFD. Control voltage or the at-motor disconnect controls the ON/OFF of the output contactor. A sequenced stop involving the output contact cannot be performed.

Safety Monitor

The Safety Monitor Option allows for independent monitoring of the output contactor status. The output contactor is provided as standard with this option. The function is implemented using the normally closed auxiliary contact which complies with
IEC 60947-5-1 for mechanically linked contacts. Two terminal blocks are provided as inputs to an external device, such as a safety circuit.

0…10V Analog Input Connector

This provides 0…10V analog input as an external frequency command from the analog input or remote potentiometer. A 5-pin micro receptacle is provided for connectivity. A shielded 5-conductor cordset or patch cord is recommended.

Catalog Number Explanation

Sensorless Vector Performance (SVP), typical of Powerflex 4 Class Drive

284

D

–

F

H

D2P3

D

–

10

–

CR

–

Option 1

–

Option 2

–

Option 3

a

b

c

d

e

f

g

h

i

j

k

a
Bulletin Number
Code	Description
284	VFD Starter

b
Communications
Code	Description
D	DeviceNet
A	ArmorPoint

c
Enclosure Type
Code	Description
F	Type 4 (IP67)
S	Type 4X

d
Torque Performance Mode
Code	Description
H	Volts per Hertz (Sensorless Vector Performance)

e
Output Current
200…240V		380…480V
Code	Description	Code	Description
B2P3	2.3 A, 0.4 kW, 0.5 Hp	D1P4	1.4 A, 0.4 kW, 0.5 Hp
B4P5	4.5 A, 0.75 kW, 1.0 Hp	D2P3	2.3 A, 0.75 kW, 1.0 Hp
B7P6	7.6 A, 1.5 kW, 2.0 Hp	D4P0	4.0 A, 1.5 kW, 2.0 Hp
—	—	D6P0	6.0 A, 2.2 kW, 3.0 Hp
—	—	D7P6	7.6 A, 3.3 kW, 5.0 Hp

f
Control Voltage
Code	Description
Z	24V DC
D	120V AC
B	240V AC

g
Short Circuit Protection (Motor Circuit Protector)
Code	Description
10	10 A Rated Device
25	25 A Rated Device

h
Control and 3-Phase Power Connections / Motor Cable Connection (CR: Conduit/Round Media) or (RR: Round/Round Media)
Code		Description
		Control Power	3-Phase Power	Motor Cable
CR	blank	Conduit Entrance	Conduit Entrance	3 m, unshielded cordset male 90°
CR	N	Conduit Entrance	Conduit Entrance	3 m, shielded cordset male 90°
CR	W ⋆	Conduit Entrance	Conduit Entrance	No cable
RR	blank	Round Media (Male Receptacle)	Round Media (Male Receptacle)	3 m, unshielded cordset male 90°
RR	N	Round Media (Male Receptacle)	Round Media (Male Receptacle)	3 m, shielded cordset male 90°
RR	W ⋆	Round Media (Male Receptacle)	Round Media (Male Receptacle)	No cable

i
Option 1
Code	Description
3	Hand/Off/Auto Selector Keypad with Jog Function

j
Option 2
Code		Description
CB	blank	Control Brake Contactor
CB	W ⋆	No cable
DB	blank	DB Brake Connector
SB	blank	Source Brake Contactor
SB	W ⋆	No cable

k
Option 3
Code	Description
OC	Output Contactor
SM ‡ §	Safety Monitor

⋆ See Accessories on Motor and Brake Cables for extended motor and brake cable lengths.
‡ The output contactor is included with the Safety Monitor option.
§ Not available with round media option (RR).

Product Selection

Build a Catalog Number

DeviceNet Network Communication

IP67/NEMA Type 4 with conduit entrance, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200...240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-FHB2P3Z-10-CR	284D-FHB2P3D-10-CR	284D-FHB2P3B-10-CR
	0.75	1	4.5	284D-FHB4P5Z-10-CR	284D-FHB4P5D-10-CR	284D-FHB4P5B-10-CR
	1.5	2	7.6	284D-FHB7P6Z-25-CR	284D-FHB7P6D-25-CR	284D-FHB7P6B-25-CR
380...480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-FHD1P4Z-10-CR	284D-FHD1P4D-10-CR	284D-FHD1P4B-10-CR
	0.75	1	2.3	284D-FHD2P3Z-10-CR	284D-FHD2P3D-10-CR	284D-FHD2P3B-10-CR
	1.5	2	4	284D-FHD4P0Z-10-CR	284D-FHD4P0D-10-CR	284D-FHD4P0B-10-CR
	2.2	3	6	284D-FHD6P0Z-25-CR	284D-FHD6P0D-25-CR	284D-FHD6P0B-25-CR
	3	5	7.6	284D-FHD7P6Z-25-CR	284D-FHD7P6D-25-CR	284D-FHD7P6B-25-CR

IP67/NEMA Type 4 with quick disconnects for ArmorConnect power media, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-FHB2P3Z-10-RR	284D-FHB2P3D-10-RR	284D-FHB2P3B-10-RR
	0.75	1	4.5	284D-FHB4P5Z-10-RR	284D-FHB4P5D-10-RR	284D-FHB4P5B-10-RR
	1.5	2	7.6	284D-FHB7P6Z-25-RR	284D-FHB7P6D-25-RR	284D-FHB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-FHD1P4Z-10-RR	284D-FHD1P4D-10-RR	284D-FHD1P4B-10-RR
	0.75	1	2.3	284D-FHD2P3Z-10-RR	284D-FHD2P3D-10-RR	284D-FHD2P3B-10-RR
	1.5	2	4	284D-FHD4P0Z-10-RR	284D-FHD4P0D-10-RR	284D-FHD4P0B-10-RR
	2.2	3	6	284D-FHD6P0Z-25-RR	284D-FHD6P0D-25-RR	284D-FHD6P0B-25-RR
	3	5	7.6	284D-FHD7P6Z-25-RR	284D-FHD7P6D-25-RR	284D-FHD7P6B-25-RR

NEMA Type 4X with conduit entrance, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-SHB2P3Z-10-CR	284D-SHB2P3D-10-CR	284D-SHB2P3B-10-CR
	0.75	1	4.5	284D-SHB4P5Z-10-CR	284D-SHB4P5D-10-CR	284D-SHB4P5B-10-CR
	1.5	2	7.6	284D-SHB7P6Z-25-CR	284D-SHB7P6D-25-CR	284D-SHB7P6B-25-CR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-SHD1P4Z-10-CR	284D-SHD1P4D-10-CR	284D-SHD1P4B-10-CR
	0.75	1	2.3	284D-SHD2P3Z-10-CR	284D-SHD2P3D-10-CR	284D-SHD2P3B-10-CR
	1.5	2	4	284D-SHD4P0Z-10-CR	284D-SHD4P0D-10-CR	284D-SHD4P0B-10-CR
	2.2	3	6	284D-SHD6P0Z-25-CR	284D-SHD6P0D-25-CR	284D-SHD6P0B-25-CR
	3	5	7.6	284D-SHD7P6Z-25-CR	284D-SHD7P6D-25-CR	284D-SHD7P6B-25-CR

NEMA Type 4X with quick disconnects for ArmorConnect power media, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-SHB2P3Z-10-RR	284D-SHB2P3D-10-RR	284D-SHB2P3B-10-RR
	0.75	1	4.5	284D-SHB4P5Z-10-RR	284D-SHB4P5D-10-RR	284D-SHB4P5B-10-RR
	1.5	2	7.6	284D-SHB7P6Z-25-RR	284D-SHB7P6D-25-RR	284D-SHB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-SHD1P4Z-10-RR	284D-SHD1P4D-10-RR	284D-SHD1P4B-10-RR
	0.75	1	2.3	284D-SHD2P3Z-10-RR	284D-SHD2P3D-10-RR	284D-SHD2P3B-10-RR
	1.5	2	4	284D-SHD4P0Z-10-RR	284D-SHD4P0D-10-RR	284D-SHD4P0B-10-RR
	2.2	3	6	284D-SHD6P0Z-25-RR	284D-SHD6P0D-25-RR	284D-SHD6P0B-25-RR
	3	5	7.6	284D-SHD7P6Z-25-RR	284D-SHD7P6D-25-RR	284D-SHD7P6B-25-RR

ArmorPoint Bus Network Communication

IP67/NEMA Type 4 with conduit entrance, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284A-FHB2P3Z-10-CR	284A-FHB2P3D-10-CR	284A-FHB2P3B-10-CR
	0.75	1	5	284A-FHB4P5Z-10-CR	284A-FHB4P5D-10-CR	284A-FHB4P5B-10-CR
	1.5	2	7.6	284A-FHB7P6Z-25-CR	284A-FHB7P6D-25-CR	284A-FHB7P6B-25-CR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284A-FHD1P4Z-10-CR	284A-FHD1P4D-10-CR	284A-FHD1P4B-10-CR
	0.75	1	2.3	284A-FHD2P3Z-10-CR	284A-FHD2P3D-10-CR	284A-FHD2P3B-10-CR
	1.5	2	4	284A-FHD4P0Z-10-CR	284A-FHD4P0D-10-CR	284A-FHD4P0B-10-CR
	2.2	3	6	284A-FHD6P0Z-25-CR	284A-FHD6P0D-25-CR	284A-FHD6P0B-25-CR
	3	5	7.6	284A-FHD7P6Z-25-CR	284A-FHD7P6D-25-CR	284A-FHD7P6B-25-CR

IP67/NEMA Type 4 with quick disconnects for ArmorConnect power media, Volts per Hertz (SVP) torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284A-FHB2P3Z-10-RR	284A-FHB2P3D-10-RR	284A-FHB2P3B-10-RR
	0.75	1	4.5	284A-FHB4P5Z-10-RR	284A-FHB4P5D-10-RR	284A-FHB4P5B-10-RR
	1.5	2	7.6	284A-FHB7P6Z-25-RR	284A-FHB7P6D-25-RR	284A-FHB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284A-FHD1P4Z-10-RR	284A-FHD1P4D-10-RR	284A-FHD1P4B-10-RR
	0.75	1	2.3	284A-FHD2P3Z-10-RR	284A-FHD2P3D-10-RR	284A-FHD2P3B-10-RR
	1.5	2	4	284A-FHD4P0Z-10-RR	284A-FHD4P0D-10-RR	284A-FHD4P0B-10-RR
	2.2	3	6	284A-FHD6P0Z-25-RR	284A-FHD6P0D-25-RR	284A-FHD6P0B-25-RR
	3	5	7.6	284A-FHD7P6Z-25-RR	284A-FHD7P6D-25-RR	284A-FHD7P6B-25-RR

Catalog Number Explanation

Sensorless Vector Control (SVC), typical of Powerflex 40 Class Drive

284

D

–

F

V

D2P3

D

–

10

–

CR

–

Option 1

–

Option 2

–

Option 3

a

b

c

d

e

f

g

h

i

j

k

a
Bulletin Number
Code	Description
284	VFD Starter

b
Communications
Code	Description
E	EtherNet/IP
D	DeviceNet
A	ArmorPoint

c
Enclosure Type
Code	Description
F	Type 4 (IP67)
S‡	Type 4X

d
Torque Performance Mode
Code	Description
V	Sensorless Vector Control and Volts per Hertz

e
Output Current
200…240V‡		380…480V		500…600V‡
Code	Description	Code	Description	Code	Description
B2P3	2.3 A, 0.4 kW, 0.5 Hp	D1P4	1.4 A, 0.4 kW, 0.5 Hp	E1P7	1.7 A, 0.75 kW, 1.0 Hp
B5P0	5.0 A, 0.75 kW, 1.0 Hp	D2P3	2.3 A, 0.75 kW, 1.0 Hp	E3P0	3.0 A, 1.5 kW, 2.0 Hp
B7P6	7.6 A, 1.5 kW, 2.0 Hp	D4P0	4.0 A, 1.5 kW, 2.0 Hp	E4P2	4.2 A, 2.2 kW, 3.0 Hp
—	—	D6P0	6.0 A, 2.2 kW, 3.0 Hp	E6P6	6.6 A, 4.0 kW, 5.0 Hp
—	—	D7P6	7.6 A, 3.3 kW, 5.0 Hp	—	—

f
Control Voltage
Code	Description
Z	24V DC
D‡	120V AC
B‡	240V AC

g
Short Circuit Protection (Motor Circuit Protector)
Code	Description
10	10 A Rated Device
25	25 A Rated Device

h
Control and 3-Phase Power Connections / Motor Cable Connection (CR: Conduit/Round Media) or (RR: Round/Round Media)
Code		Description
		Control Power	3-Phase Power	Motor Cable
CR	blank	Conduit Entrance	Conduit Entrance	3 m, unshielded cordset male 90°
CR	N	Conduit Entrance	Conduit Entrance	3 m, shielded cordset male 90°
CR	W ⋆	Conduit Entrance	Conduit Entrance	No cable
RR	blank	Round Media (Male Receptacle)	Round Media (Male Receptacle)	3 m, unshielded cordset male 90°
RR	N	Round Media (Male Receptacle)	Round Media (Male Receptacle)	3 m, shielded cordset male 90°
RR	W ⋆	Round Media (Male Receptacle)	Round Media (Male Receptacle)	No cable

i
Option 1
Code	Description
3	Hand/Off/Auto Selector Keypad with Jog Function

j
Option 2
Code		Description
CB‡	blank	Control Brake Contactor
CB‡	W ⋆	No cable
DB	blank	DB Brake Connector
SB	blank	Source Brake Contactor
SB	W ⋆	No cable

k
Option 3
Code	Description
A10‡	0…10V Analog Input
EMI	EMI Filter
OC	Output Contactor
SM‡ § ♣	Safety Monitor

⋆ See Accessories on Motor and Brake Cables for extended motor and brake cable lengths.
‡ Not available with EtherNet/IP.
§ Not available with round media option (RR).
♣ The output contactor is included with the Safety Monitor option.

Product Selection

Build a Catalog Number

EtherNet/IP Network Communication

IP67/NEMA Type 4 with conduit entrance, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage
				Cat. No.
380...480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284E-FVD1P4Z-10-CR
	0.75	1	2.3	284E-FVD2P3Z-10-CR
	1.5	2	4	284E-FVD4P0Z-10-CR
	2.2	3	6	284E-FVD6P0Z-25-CR
	3	5	7.6	284E-FVD7P6Z-25-CR

IP67/NEMA Type 4 with quick disconnects for ArmorConnect power media, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 480V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage
				Cat. No.
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284E-FVD1P4Z-10-RR
	0.75	1	2.3	284E-FVD2P3Z-10-RR
	1.5	2	4	284E-FVD4P0Z-10-RR
	2.2	3	6	284E-FVD6P0Z-25-RR
	3	5	7.6	284E-FVD7P6Z-25-RR

DeviceNet Network Communication

IP67/NEMA Type 4 with conduit entrance, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200...240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-FVB2P3Z-10-CR	284D-FVB2P3D-10-CR	284D-FVB2P3B-10-CR
	0.75	1	5	284D-FVB5P0Z-10-CR	284D-FVB5P0D-10-CR	284D-FVB5P0B-10-CR
	1.5	2	7.6	284D-FVB7P6Z-25-CR	284D-FVB7P6D-25-CR	284D-FVB7P6B-25-CR
380...480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-FVD1P4Z-10-CR	284D-FVD1P4D-10-CR	284D-FVD1P4B-10-CR
	0.75	1	2.3	284D-FVD2P3Z-10-CR	284D-FVD2P3D-10-CR	284D-FVD2P3B-10-CR
	1.5	2	4	284D-FVD4P0Z-10-CR	284D-FVD4P0D-10-CR	284D-FVD4P0B-10-CR
	2.2	3	6	284D-FVD6P0Z-25-CR	284D-FVD6P0D-25-CR	284D-FVD6P0B-25-CR
	3	5	7.6	284D-FVD7P6Z-25-CR	284D-FVD7P6D-25-CR	284D-FVD7P6B-25-CR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284D-FVE1P7Z-10-CR	284D-FVE1P7D-10-CR	284D-FVE1P7B-10-CR
	1.5	2	3	284D-FVE3P0Z-10-CR	284D-FVE3P0D-10-CR	284D-FVE3P0B-10-CR
	2.2	3	4.2	284D-FVE4P2Z-10-CR	284D-FVE4P2D-10-CR	284D-FVE4P2B-10-CR
	4	5	6.1	284D-FVE6P6Z-25-CR	284D-FVE6P6D-25-CR	284D-FVE6P6B-25-CR

IP67/NEMA Type 4 with quick disconnects for ArmorConnect power media, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-FVB2P3Z-10-RR	284D-FVB2P3D-10-RR	284D-FVB2P3B-10-RR
	0.75	1	5	284D-FVB5P0Z-10-RR	284D-FVB5P0D-10-RR	284D-FVB5P0B-10-RR
	1.5	2	7.6	284D-FVB7P6Z-25-RR	284D-FVB7P6D-25-RR	284D-FVB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-FVD1P4Z-10-RR	284D-FVD1P4D-10-RR	284D-FVD1P4B-10-RR
	0.75	1	2.3	284D-FVD2P3Z-10-RR	284D-FVD2P3D-10-RR	284D-FVD2P3B-10-RR
	1.5	2	4	284D-FVD4P0Z-10-RR	284D-FVD4P0D-10-RR	284D-FVD4P0B-10-RR
	2.2	3	6	284D-FVD6P0Z-25-RR	284D-FVD6P0D-25-RR	284D-FVD6P0B-25-RR
	3	5	7.6	284D-FVD7P6Z-25-RR	284D-FVD7P6D-25-RR	284D-FVD7P6B-25-RR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284D-FVE1P7Z-10-RR	284D-FVE1P7D-10-RR	284D-FVE1P7B-10-RR
	1.5	2	3	284D-FVE3P0Z-10-RR	284D-FVE3P0D-10-RR	284D-FVE3P0B-10-RR
	2.2	3	4.2	284D-FVE4P2Z-10-RR	284D-FVE4P2D-10-RR	284D-FVE4P2B-10-RR
	4	5	6.1	284D-FVE6P6Z-25-RR	284D-FVE6P6D-25-RR	284D-FVE6P6B-25-RR

DeviceNet Network Communication, Continued

NEMA Type 4X with conduit entrance, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-SVB2P3Z-10-CR	284D-SVB2P3D-10-CR	284D-SVB2P3B-10-CR
	0.75	1	5	284D-SVB5P0Z-10-CR	284D-SVB5P0D-10-CR	284D-SVB5P0B-10-CR
	1.5	2	7.6	284D-SVB7P6Z-25-CR	284D-SVB7P6D-25-CR	284D-SVB7P6B-25-CR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-SVD1P4Z-10-CR	284D-SVD1P4D-10-CR	284D-SVD1P4B-10-CR
	0.75	1	2.3	284D-SVD2P3Z-10-CR	284D-SVD2P3D-10-CR	284D-SVD2P3B-10-CR
	1.5	2	4	284D-SVD4P0Z-10-CR	284D-SVD4P0D-10-CR	284D-SVD4P0B-10-CR
	2.2	3	6	284D-SVD6P0Z-25-CR	284D-SVD6P0D-25-CR	284D-SVD6P0B-25-CR
	3	5	7.6	284D-SVD7P6Z-25-CR	284D-SVD7P6D-25-CR	284D-SVD7P6B-25-CR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284D-SVE1P7Z-10-CR	284D-SVE1P7D-10-CR	284D-SVE1P7B-10-CR
	1.5	2	3	284D-SVE3P0Z-10-CR	284D-SVE3P0D-10-CR	284D-SVE3P0B-10-CR
	2.2	3	4.2	284D-SVE4P2Z-10-CR	284D-SVE4P2D-10-CR	284D-SVE4P2B-10-CR
	4	5	6.1	284D-SVE6P6Z-25-CR	284D-SVE6P6D-25-CR	284D-SVE6P6B-25-CR

NEMA Type 4X with quick disconnects for ArmorConnect power media, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284D-SVB2P3Z-10-RR	284D-SVB2P3D-10-RR	284D-SVB2P3B-10-RR
	0.75	1	5	284D-SVB5P0Z-10-RR	284D-SVB5P0D-10-RR	284D-SVB5P0B-10-RR
	1.5	2	7.6	284D-SVB7P6Z-25-RR	284D-SVB7P6D-25-RR	284D-SVB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284D-SVD1P4Z-10-RR	284D-SVD1P4D-10-RR	284D-SVD1P4B-10-RR
	0.75	1	2.3	284D-SVD2P3Z-10-RR	284D-SVD2P3D-10-RR	284D-SVD2P3B-10-RR
	1.5	2	4	284D-SVD4P0Z-10-RR	284D-SVD4P0D-10-RR	284D-SVD4P0B-10-RR
	2.2	3	6	284D-SVD6P0Z-25-RR	284D-SVD6P0D-25-RR	284D-SVD6P0B-25-RR
	3	5	7.6	284D-SVD7P6Z-25-RR	284D-SVD7P6D-25-RR	284D-SVD7P6B-25-RR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284D-SVE1P7Z-10-RR	284D-SVE1P7D-10-RR	284D-SVE1P7B-10-RR
	1.5	2	3	284D-SVE3P0Z-10-RR	284D-SVE3P0D-10-RR	284D-SVE3P0B-10-RR
	2.2	3	4.2	284D-SVE4P2Z-10-RR	284D-SVE4P2D-10-RR	284D-SVE4P2B-10-RR
	4	5	6.1	284D-SVE6P6Z-25-RR	284D-SVE6P6D-25-RR	284D-SVE6P6B-25-RR

ArmorPoint Bus Network Communication

IP67/NEMA Type 4 with conduit entrance, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284A-FVB2P3Z-10-CR	284A-FVB2P3D-10-CR	284A-FVB2P3B-10-CR
	0.75	1	5	284A-FVB5P0Z-10-CR	284A-FVB5P0D-10-CR	284A-FVB5P0B-10-CR
	1.5	2	7.6	284A-FVB7P6Z-25-CR	284A-FVB7P6D-25-CR	284A-FVB7P6B-25-CR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284A-FVD1P4Z-10-CR	284A-FVD1P4D-10-CR	284A-FVD1P4B-10-CR
	0.75	1	2.3	284A-FVD2P3Z-10-CR	284A-FVD2P3D-10-CR	284A-FVD2P3B-10-CR
	1.5	2	4	284A-FVD4P0Z-10-CR	284A-FVD4P0D-10-CR	284A-FVD4P0B-10-CR
	2.2	3	6	284A-FVD6P0Z-25-CR	284A-FVD6P0D-25-CR	284A-FVD6P0B-25-CR
	3	5	7.6	284A-FVD7P6Z-25-CR	284A-FVD7P6D-25-CR	284A-FVD7P6B-25-CR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284A-FVE1P7Z-10-CR	284A-FVE1P7D-10-CR	284A-FVE1P7B-10-CR
	1.5	2	3	284A-FVE3P0Z-10-CR	284A-FVE3P0D-10-CR	284A-FVE3P0B-10-CR
	2.2	3	4.2	284A-FVE4P2Z-10-CR	284A-FVE4P2D-10-CR	284A-FVE4P2B-10-CR
	4	5	6.1	284A-FVE6P6Z-25-CR	284A-FVE6P6D-25-CR	284A-FVE6P6B-25-CR

IP67/NEMA Type 4 with quick disconnects for ArmorConnect power media, Sensorless Vector Control, and Volts per Hertz torque performance, Up to 575V AC

Input Voltage	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]	24V DC Control Voltage	120V AC Control Voltage	240V AC Control Voltage
				Cat. No.	Cat. No.	Cat. No.
200…240V, 50/60 Hz 3-Phase	0.4	0.5	2.3	284A-FVB2P3Z-10-RR	284A-FVB2P3D-10-RR	284A-FVB2P3B-10-RR
	0.75	1	5	284A-FVB5P0Z-10-RR	284A-FVB5P0D-10-RR	284A-FVB5P0B-10-RR
	1.5	2	7.6	284A-FVB7P6Z-25-RR	284A-FVB7P6D-25-RR	284A-FVB7P6B-25-RR
380…480V, 50/60 Hz 3-Phase	0.4	0.5	1.4	284A-FVD1P4Z-10-RR	284A-FVD1P4D-10-RR	284A-FVD1P4B-10-RR
	0.75	1	2.3	284A-FVD2P3Z-10-RR	284A-FVD2P3D-10-RR	284A-FVD2P3B-10-RR
	1.5	2	4	284A-FVD4P0Z-10-RR	284A-FVD4P0D-10-RR	284A-FVD4P0B-10-RR
	2.2	3	6	284A-FVD6P0Z-25-RR	284A-FVD6P0D-25-RR	284A-FVD6P0B-25-RR
	3	5	7.6	284A-FVD7P6Z-25-RR	284A-FVD7P6D-25-RR	284A-FVD7P6B-25-RR
460…600V, 50/60 Hz 3-Phase	0.75	1	1.7	284A-FVE1P7Z-10-RR	284A-FVE1P7D-10-RR	284A-FVE1P7B-10-RR
	1.5	2	3	284A-FVE3P0Z-10-RR	284A-FVE3P0D-10-RR	284A-FVE3P0B-10-RR
	2.2	3	4.2	284A-FVE4P2Z-10-RR	284A-FVE4P2D-10-RR	284A-FVE4P2B-10-RR
	4	5	6.1	284A-FVE6P6Z-25-RR	284A-FVE6P6D-25-RR	284A-FVE6P6B-25-RR

Options — Factory Installed

Description		Cat. No. Modification
	Hand/Off/Auto Selector and Jog Keypad	-3
	Safety Monitor (includes output contactor)‡ §	-SM
	EMI Filter	-EMI
	Output Contactor	-OC
	Shielded motor cable	-CRN
	Supplied without motor cable	-CRW
	Control Brake supplied with cable‡	-CB
	Control Brake supplied without cable‡	-CBW
	Source brake supplied with cable	-SB
	Source brake supplied without cable	-SBW
	0…10 Analog Input‡	-A10
	Dynamic Brake Connector (IP20 brake)	-DB
	Dynamic Brake Connector (IP67 brake)	-DB1
	ArmorConnect Power Media Connectivity, ArmorStart supplied with shielded motor cable	-RRN
	ArmorConnect Power Media Connectivity, ArmorStart supplied without motor cable	-RRW
‡ Not available with EtherNet/IP communications.
§ Not available with round media option (RR).

Accessories

DeviceNet Media ∆ 

Description		Length [m (ft)]	Cat. No.
			Sealed
	KwikLink pigtail drops are Insulation Displacement Connector (IDC) with integral Class 1 round cables for interfacing devices or power supplies to flat cable	1 (3.3)	1485P-P1E4-B1-N5
		2 (6.5)	1485P-P1E4-B2-N5
		3 (9.8)	1485P-P1E4-B3-N5
		6 (19.8)	1485P-P1E4-B6-N5
	DeviceNet Mini- T-Port Tap	Left Keyway	1485P-P1N5-MN5KM
		Right Keyway	1485P-P1N5-MN5NF
Description		Connector	Cat. No.
	Gray PVC Thin Cable	Mini Straight Female Mini Straight Male	1485G-P‡ N5-M5
		Mini Straight Female Mini Right Angle Male	1485G-P‡ W5-N5
		Mini Right Angle Female Mini Straight Male	1485G-P‡ M5-Z5
		Mini Right Angle Female Mini Straight Male	1485G-P‡ W5-Z5
	Thick Cable	Mini Straight Female Mini Straight Male	1485C-P§ N5-M5
		Mini Straight Female Mini Right Angle Male	1485C-P§ W5-N5
		Mini Right Angle Female Mini Straight Male	1485C-P§ M5-Z5
		Mini Right Angle Female Mini Straight Male	1485C-P§ W5-Z5
Description		Length m (ft)	Cat. No.
	DeviceNet Configuration Terminal Used to interface with objects on a DeviceNet network. Includes 1 m communications cable.	1 (3.3)	193-DNCT
	Communication cable, color-coded bare leads	1 (3.3)	193-CB1
	Communication cable, microconnector (male)	1 (3.3)	193-CM1
	Panel Mount Adapter/Door Mount Bezel Kit	—	193-DNCT-BZ1
∆ See On-Machine Connectivity Catalog for complete cable selection information.
‡ Replace symbol with desired length in meters (Example: 1485G-P1N5-M5 for a 1 m cable). Standard cable lengths: 1, 2, 3, 4, 5, and 6 m.
§ Replace symbol with desired length in meters (Example: 1485C-P1N5-M5 for a 1 m cable). Standard cable lengths: 1, 2, 3, 4, 5, 6, 8, 10, 12, 18, 24, and 30 m.

Industrial EtherNet Media∆ 

Description	Connector Type	Unshielded
		Cat. No.
M12, D-Code Patchcords and Cordsets
	Straight male to straight male	1585D-M4TBDM-⋆
	Straight male to right angle male	1585D-M4TBDE-⋆
	Right angle male to right angle male	1585D-E4TBDE-⋆
	Straight male to straight female	1585D-M4TBDF-⋆
Front Mount Receptacle
	Front mount female to RJ45	1585D-D4TBJM-⋆
Transition Cable
	Straight male to RJ45	1585D-M4TBJM-⋆

Description	Conductors	Jacket Material	Cable Type	Jacket Color	Cat. No.
RJ45 Patchcords
	4-pair	Riser PVC	Unshielded twisted pair	Teal	1585J-M8PBJM-⋆
		High-flex TPE		Teal	1585J-M8TBJM-⋆
M12 to RJ45 Bulkhead Adapter
	Transition from IP20 environment to IP67 environment In-cabinet connectivity with RJ45 connector providing On-Machine solution with M12 D Code connector Differential 100 W terminators used for unused pairs Cat 5e				1585A-DD4JD
⋆ Lengths available in 0.3, 0.6, 1, 2, 5, 10, 15, and additional increments of 5 m, up to 75 m.
∆ See On-Machine Connectivity Catalog for complete cable selection information.

ArmorPoint^® Media ♣ 

Description	Length [m (ft)]	Cat. No.
ArmorPoint Bus Extension Cable including Terminating Resistor	1 (3.3)	280A-EXT1
Extension Cable to connect two ArmorStart Distributed Motor Controllers to ArmorPoint communication protocol	1 (3.3)	280A-EXTCABLE
♣  ArmorPoint media is only available with an IP67/NEMA Type 4 rating.

Sensor Media ♠ 

DeviceNet/ArmorPoint Communications
Description		ArmorStart I/O Connection	Pin Count	Connector	Cat. No.
	DC Micro Patchcord	Input	4-pin	Straight Female Straight Male	889D-F4ACDM-♦
				Straight Female Right Angle Male	889D-F4ACDE-♦
	DC Micro V-Cable	Input	4-pin	Straight Female	879D-F4ACDM-♦
				Right Angle Female	879D-R4ACM-♦
	AC Micro Patchcord	Output	3-pin	Straight Female Straight Male	889R-F3AERM-♦
				Straight Female Right Angle Male	889R-F3AERE-♦

EtherNet/IP Communications
Description		ArmorStart I/O Connection	Pin Count	Connector	Cat. No.
	DC Micro Patchcord	Input/Output	4-pin	Straight Female Straight Male	889D-F4ACDM-♦
				Straight Female Right Angle Male	889D-F4ACDE-♦
	DC Micro V-Cable	Input	4-pin	Straight Female	879D-F4ACDM-♦
				Right Angle Male	879D-R4ACM-♦
♠ See On-Machine Connectivity Catalog for complete cable selection information.
♦ Replace symbol with desired length in meters (Example: 889D-F4ACDM-1 for a 1 m cable). Standard cable lengths: 1, 2, 5, and 10 m.

Motor and Brake Cables

Description		Cable Rating	Length [m (ft)]	Cat. No.
Motor Cable Cordsets	90° M22 Motor Cordset	IP67/NEMA Type 4	3 (9.8)	280-MTR22-M3
			6 (19.6)	280-MTR22-M6
			10 (32.8)	280-MTR22-M10
			14 (45.9)	280-MTR22-M14
			20 (65.6)	280-MTR22-M20
	90° M35 Motor Cordset	IP67/NEMA Type 4	3 (9.8)	280-MTR35-M3
			6 (19.6)	280-MTR35-M6
			10 (32.8)	280-MTR35-M10
			14 (45.9)	280-MTR35-M14
			20 (65.6)	280-MTR35-M20
	90° M22 Motor Cordset	IP69K/NEMA 4X	3 (9.8)	280S-MTR22-M3
			6 (19.6)	280S-MTR22-M6
			14 (45.9)	280S-MTR22-M14
	90° M35 Motor Cordset	IP69K/NEMA 4X	6 (19.6)	280S-MTR35-M6
			14 (45.9)	280S-MTR35-M14
Motor Cable Cordsets, High Flex⋆	90° M22 Motor Cordset	IP67/NEMA Type 4	3 (9.8)	280-MTRF22-M3
			6 (19.6)	280-MTRF22-M6
			8 (26.2)	280-MTRF22-M8
			10 (32.8)	280-MTRF22-M10
			14 (45.9)	280-MTRF22-M14
			20 (65.6)	280-MTRF22-M20
Motor Cable Cordsets, Shielded (VFD)	90° M22 Motor Cordset	IP67/NEMA Type 4	3 (9.8)	284-MTRS22-M3
			6 (19.6)	284-MTRS22-M6
			14 (45.9)	284-MTRS22-M14
	90° M22 Motor Cordset	IP69K/NEMA Type 4X	3 (9.8)	284S-MTRS22-M3
			6 (19.6)	284S-MTRS22-M6
			14 (45.9)	284S-MTRS22-M14
Extended Source/Control Brake Cable Cordsets	90° M25 Source Brake Cable	IP67/NEMA Type 4	6 (19.6)	285-BRC25-M6
			14 (45.9)	285-BRC25-M14
		IP69K	6 (19.6)	285S-BRC25-M6
			14 (45.9)	285S-BRC25-M14
Extended Source/Control Brake Cable Cordsets, High Flex⋆	90° M25 Source Brake Cable	IP67/NEMA Type 4	3 (9.8)	285-BRCF25-M3
			6 (19.6)	285-BRCF25-M6
			10 (32.8)	285-BRCF25-M10
			14 (45.9)	285-BRCF25-M14
			20 (65.6)	285-BRCF25-M20
Dynamic Brake Cables	M22 Dynamic Brake Cable (DB Option)	IP67/NEMA Type 4	3 (9.8)	285-DBK22-M3
		IP69K	3 (9.8)	285S-DBK22-M3
Description	Description	Cable Rating	Length [m (ft)]	Cat. No.
Motor Cable Patchcords	90° Male/Straight Female M22	IP67/NEMA Type 4	1 (3.3)	280-MTR22-M1D
			3 (9.8)	280-MTR22-M3D
	90° Male/Straight Female M35	IP67/NEMA Type 4	1 (3.3)	280-MTR35-M1D
			3 (9.8)	280-MTR35-M3D
	90° Male/Straight Female M22	IP69K/NEMA Type 4X	1 (3.3)	280S-MTR22-M1D
			3 (9.8)	280S-MTR22-M3D
	90° Male/Straight Female M35	IP69K/NEMA Type 4X	1 (3.3)	280S-MTR35-M1D
			3 (9.8)	280S-MTR35-M3D
Motor Cable Patchcords, Shielded (VFD)	90° Male/Straight Female M22	IP67/NEMA Type 4	1 (3.3)	284-MTRS22-M1D
			3 (9.8)	284-MTRS22-M3D
	90° Male/Straight Female M22	IP69K/NEMA Type 4X	1 (3.3)	284S-MTRS22-M1D
			3 (9.8)	284S-MTRS22-M3D
⋆ 14 million flex cycles, bend radius is maximum 8X the cable diameter (0.362 in. OD).

Sealing Caps

	ArmorPoint		DeviceNet		EtherNet/IP
	Input	Output	Input	Output	Input	Output
	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
Plastic Sealing Cap (M12)⋆	—	1485A-M12	1485A-M12	1485A-M12	1485A-M12	1485A-M12
AC Micro Aluminum Sealing Cap⋆	—	889A-RMCAP	—	889A-RMCAP	—	—
Stainless Steel Sealing Cap§	—	889AS-RMCAP	1485AS-C3	889AS-RMCAP	—	—
Motor Connector Aluminum Sealing Cap (M22) for 10 A protection⋆	—	1485A-C1	—	1485A-C1	—	1485A-C1
Motor Connector Aluminum Sealing Cap (M35) for 25 A protection⋆	—	889A-QMCAP	—	889A-QMCAP	—	889A-QMCAP
Dynamic Brake Connector (M22)	—	1485A-C1	—	1485A-C1	—	1485A-C1
Source/Control Brake Cap (M25)	—	∆	—	∆	—	∆
⋆ To achieve IP67 rating, sealing caps must be installed on all unused I/O connections.
§ To achieve IP69K/NEMA 4X rating, sealing caps must be installed on all unused I/O connections.
∆ Contact your local Rockwell Automation sales office or Allen-Bradley distributor.

Handle and Cord Accessories

	Description	Cat. No.
	Locking Tag Padlock attachment to the lockable handles Up to three padlocks 4…8 mm (5/16 in.) Æ shackle	140M-C-M3
	Replacement At-Motor Disconnect Handle Kit includes: (1) handle, (1) guard, and (3) screws	280-DISHDL
Cord grips for ArmorStart devices with 10 A short circuit protection rating
	3/4 in. Strain relief cord connector and 3/4 in. lock nut Cable range: 0.31…0.56 in. Used with control power media cordset - Example cat. no.: 889N-M65GF-M2	Thomas & Betts Cord Grip Cat. No. 2931NM
	1 in. Strain relief cord connector and 1 in. lock nut Cable range: 0.31…0.56 in. Used with control power media cordset - Example cat. no.: 280-PWR22G-M	Thomas & Betts Cord Grip Cat. No. 2940NM
Cord grips for ArmorStart devices with 25 A short circuit protection rating
	3/4 in. Strain relief cord connector and 3/4 in. lock nut Cable range: 0.31…0.56 in. Used with control power media cordset - Example cat. no.: 889N-M65GF-M2	Thomas & Betts Cord Grip Cat. No. 2931NM
	1 in. Strain relief cord connector and 1 in. lock nut Cable range: 0.70…0.95 in. Used with three-phase power media cordset - Example cat. no.: 280-PWR35G-M1	Thomas & Betts Cord Grip Cat. No. 2942NM

ArmorStart Bulletin 284 Option DB (IP20) Resistor Installation Dimensions

Dimensions are in millimeters (inches) and weights are in kilograms (pounds). Dimensions are not intended to be used for manufacturing purposes.

Frame	Cat. No.	Weight [kg (lb)]
A	AK-R2-091P500, AK-R2-047P500, AK-R2-360P500	1.1 (2.5)
B	AK-R2-030P1K2, AK-R2-120P1K2	2.7 (6)

Recommended thermostat control wiring to prevent dynamic brake overheating







Peer-to-Peer Communications



(ZIP) Zone interlocking Parameters

The Zone Control capabilities of ArmorStart Distributed Motor Controller is ideal for large horsepower (0.5…10 Hp) motored conveyors. The ArmorStart Distributed Motor Controllers have built-in DeviceNet Communications, DeviceLogix technology, and the added Zone Interlocking Parameters (ZIP), which allow one ArmorStart to consume data directly from up to four other DeviceNet nodes without going through the network scanner. These direct communications between conveyor zones are beneficial in a merge, diverter, and accumulation conveyor applications.

ArmorStart to ArmorPoint Connectivity - (Networks other than DeviceNet)



When connecting to the Bulletin 1738 ArmorPoint Distributed I/O product, a network adapter and at least one ArmorPoint Digital Output, Digital Input, Analog, AC and Relay product, or Specialty product must be selected. The ArmorPoint Distributed I/O can accomodate up to 63 modules per network node. The cable that connects the ArmorPoint Distributed I/O product to the ArmorStart Distributed Motor Controller is the Cat. No. 280A-EXT1. The Cat. No. 280A-EXT1 includes an ArmorPoint bus extension cable and a network terminating resistor.

Note:Access to DeviceLogix programming is available with RSNetworx for DeviceNet.



If an additional ArmorStart Distributed Motor Controller is to be connected, the Cat. No. 280A-EXTCABLE will be required. A maximum of two ArmorStart Distributed Motor Controllers can be connected to the Bulletin 1738 Distributed I/O.

I/O Expansion with DeviceNet

If the I/O capability of the Bulletin 280/281D ArmorStart Distributed Motor Controller needs to be expanded beyond the standard four inputs and two outputs, the ArmorStart Distributed Motor Controller with the DeviceNet communication protocol can be configured to the ADNX Architecture, in which the ArmorStart is part of the DeviceNet subnet, using the Cat. No. 1738-ADNX ArmorPoint Distributed I/O product.



Bulletin 1738 ArmorPoint Distributed I/O Products

Digital Output Products

Description		Cat. No.
	24V DC, eight source output with eight M12 connectors	1738-OB8EM12
	24V DC, eight source output with eight M8 connectors	1738-OB8EM8
	24V DC, four source output with four M12 connectors	1738-OB4EM12
	24V DC, four source output with four M8 connectors	1738-OB4EM8
	24V DC, two source output with two M12 connectors	1738-OB2EM12
	24V DC, two source output, 2 A prot. with two M12 connectors	1738-OB2EPM12
	24V DC, four sink output with four M12 connectors	1738-OV4EM12

Digital Input Products

Description		Cat. No.
	24V DC, eight sink input with four M12 connectors, two points per connector	1738-IB8M12
	24V DC, eight sink input with eight M8 connectors	1738-IB8M8
	24V DC, eight sink input with one M23 connector	1738-IB8M23
	24V DC, four sink input with four M12 connectors	1738-IB4M12
	24V DC, four sink input with four M8 connectors	1738-IB4M8
	24V DC, two sink input with two M12 connectors	1738-IB2M12
	24V DC, four source input with four M12 connectors	1738-IV4M12

Analog Products

Description		Cat. No.
	24V DC analog current input with two M12 connectors	1738-IE2CM12
	24V DC analog voltage input with two M12 connectors	1738-IE2VM12
	24V DC analog current output with two M12 connectors	1738-OE2CM12
	24V DC analog voltage output with two M12 connectors	1738-OE2VM12
	24V DC, two thermocouple input	1738-IT2IM12
	24V DC, two RTD input	1738-IR2M12

Power Supply Products

Description		Cat. No.
	ArmorPoint I/O Field Potential Distributor Module	1738-FPD
	24V DC Expansion Power Supply	1738-EP24DC

AC and Relay Products

Description		Cat. No.
	24V DC Coil, N.O. DPST relay with two M12 connectors	1738-OW4M12
	24V DC Coil, N.O. DPST relay with two AC M12 connectors	1738-OW4M12AC
	120V AC, two input with two AC 4-pin M12 connectors	1738-IA2M12AC4
	120V AC, two input with two AC 3-pin M12 connectors	1738-IA2M12AC3
	120/230V AC, two output with two AC 3-pin M12 connectors	1738-OA2M12AC3

Specialty Products

Description		Cat. No.
	ArmorPoint I/O RS-232 ASCII Serial Interface Module	1738-232ASCM12
	ArmorPoint I/O RS-485 ASCII Serial Interface Module	1738-485ASCM12
	24V DC Very High Speed Counter Module	1738-VHSC24M23
	ArmorPoint 5V Encoder/Counter Module	1738-IJM23
	ArmorPoint Synchronous Serial Interface Module with Absolute Encoder	1738-SSIM23

Adapter Products

Description		Cat. No.
	ArmorPoint DeviceNet Adapter Module, Drop or Pass-through, with male and female M12 connectors	1738-ADN12
	ArmorPoint DeviceNet Adapter Module, Drop only, with male M18 connector	1738-ADN18
	ArmorPoint DeviceNet Adapter Module, Drop or Pass-through, with male and female M18 connectors	1738-ADN18P
	ArmorPoint DeviceNet 24V DC Adapter Module with subnet expansion	1738-ADNX
	ArmorPoint Redundant ControlNet Adapter Module	1738-ACNR
	ArmorPoint Ethernet/IP 10/100 Mbps Adapter Module	1738-AENT
	ArmorPoint I/O 2-Port EtherNet/IP Adapter (star, tree, linear, or ring topology)⋆	1738-AENTR
⋆ Requires a 24V DC expansion power unit (cat. no. 1738-EP24DC) when two ArmorStarts are connected to point bus.

Specifications

Connections

Bulletin 284E ArmorStart with EtherNet/IP Communications



Bulletin 284D ArmorStart with DeviceNet Communications



Bulletin 284A ArmorStart for the ArmorPoint Bus Backplane

⋆ Only available with SVC.

ArmorStart Receptacle Pin Outs

Receptacle Connections for 0…10V Analog Input (M22)

Pin 1: 10V DC Pin 2: 0…10V input Pin 3: Analog common Pin 4: Analog output Pin 5: NC (no connection)

Receptacle Connections for ArmorPoint Interface (OUT)

Pin 1: CAN high Pin 2: Common Pin 3: +5V Pin 4: CAN low Pin 5: Enable out Pin 7: Common Pin 8: NC (no connection)

Receptacle Connections for ArmorPoint Interface (IN)

Pin 1: CAN high Pin 2: Common Pin 3: +5V Pin 4: CAN low Pin 5: Enable out Pin 7: Common Pin 8: PE

Receptacle Connections for DeviceNet Connector

Pin 1: Drain (no connection) Pin 2: +VDNET Pin 3: -VDNET Pin 4: CAN_H Pin 5: CAN_L

Receptacle Connections for EtherNet/IP (M12)

Pin 1: Tx+ Pin 2: Rx+ Pin 3: Tx- Pin 4: Rx-

Receptacle Connections for Input (M12)

Pin 1: +24V (A3 or DNET) Pin 2: Input 0 Pin 3: Common Pin 4: Input 1 Pin 5: NC (no connection)

Receptacle Connections for Output, EtherNet/IP Version (M12)

Pin 1: NC (no connection) Pin 2: NC (no connection) Pin 3: Common Pin 4: Output +24V DC (A1) Pin 5: NC (no connection)

Receptacle Connections for Output, DeviceNet or ArmorPoint Version (M12)

Pin 1: PE Pin 2: Return Pin 3: Relay out

Receptacle Connections for Dynamic Brake (M22)

Pin 1: GND (green/yellow) Pin 2: BR+ (black) Pin 3: BR- (white)

Receptacle Connections for Incoming Control Power (M22)

Pin 1: Unswitched (A3)(red) Pin 2: Common (A2)(black) Pin 3: PE (green) Pin 4: Not used (blank) Pin 5: Switched (A1)(blue) Pin 6: Not used (white)

Receptacle Connections for Source or Control Brake (M25)

Pin 1: L1 (black) Pin 2: GND (green/yellow) Pin 3: L2 (white)

Receptacle Connections for Motor Connector (M22)

Pin 1: T1 (black) Pin 2: T2 (white) Pin 3: T3 (red) Pin 4: Ground (green/yellow)

Receptacle Connections for Incoming 3-phase Power -
10 A Short Circuit Protection (M22)

Pin 1: L1 (black) Pin 2: L2 (white) Pin 3: L3 (red) Pin 4: Ground (green/yellow)

Receptacle Connections for Incoming 3-phase Power -
25 A Short Circuit Protection (M35)

Pin 1: L1 (black) Pin 2: Ground (green/yellow) Pin 3: L3 (red) Pin 4: L2 (white)

Electrical Ratings		UL/NEMA			IEC
Power Circuit	Rated Operation Voltage	200…575V			200…500V
	Rate Insulation Voltage	600V			600V
	Rated Impulsed Voltage	6 kV			6 kV
	Dielectric Withstand	2200V AC			2500V AC
	Operating Frequency	50/60 Hz			50/60 Hz
	Utilization Category	N/A			AC-3
	Protection Against Shock	N/A			IP2X
	Rated Maximum Operating Current	2.5 A
		5.5 A
		16 A
Control Circuit	Rated Operation Voltage	24V DC (+10%, -15%) A2 (should be grounded at voltage source)
		120V AC (+10%, -15%) A2 (should be grounded at voltage source)
		240V AC (+10%, -15%) A2 (should be grounded at voltage source)
	Rate Insulation Voltage	250V			250V
	Rated Impulsed Voltage	—			4 kV
	Dielectric Withstand	1500V AC			2000V AC
	Overvoltage Category	—			III
	Operating Frequency	50/60 Hz			50/60 Hz
Short Circuit Protection	SCPD Performance Type 1	Current Rating	Voltage	480Y/277V	480Y/480V	600Y/347V	600V
		10 A	Sym. Amps RMS	65 kA	65 kA	30 kA	30 kA
		25 A		30 kA	30 kA	30 kA	30 kA
	SCPD List	Size per NFPA 70 (NEC) or NFPA 79 for Group Motor Applications

		UL/NEMA	IEC
Environmental	Operating Temperature Range	-20…+40 °C (-4…+104 °F)
	Storage and Transportation Temperature Range	–25….+85 °C (–13…+185 °F)
	Altitude	1000 m
	Humidity	5…95% (non-condensing)
	Pollution Degree	3
	Enclosure Ratings	NEMA 4/12/13	IP67
		NEMA 4X	IP69K
	Approximate Shipping Weight	13.6 kg (30 lb)
Mechanical	Resistance to Shock
	Operational	15 G
	Non-Operational	30 G
	Resistance to Vibration
	Operational	1 G, 0.15 mm (0.006 in.) displacement
	Non-Operational	2.5 G, 0.38 mm (0.015 in.) displacement
	Wire Size	Primary/Secondary terminal: (16 …10 AWG)	Primary/Secondary terminal: 1.5…4.0 mm2
	Tightening Torque	Primary terminal: 10.8 lb•in Secondary terminal: 4.5 lb•in	Primary terminal: (1.2 N•m) Secondary terminal: (0.5 N•m)
	Wire Strip Length	0.35 in. (9 mm)
	Control and Safety Monitor Inputs
	Wire Size	(18…10 AWG)	1.0…4.0 mm2
	Tightening Torque	6.2 lb•in	0.7 N•m
	Wire Strip Length	0.35 in. (9 mm)
	Disconnect Lock Out	Maximum of 5/16 in. (8 mm) lock shackle or hasp. The hasp should not exceed 5/16 in. (8 mm) when closed, or damage will occur to disconnect guard.
EMC Emission Levels	Conducted Radio Frequency Emissions	10V rms Communication cables 10V rms (PE) 150 kHz…80 MHz
	Radiated Emissions	Class A
EMC Immunity Levels	Electrostatic Discharge	4 kV contact and 8 kV Air
	Radio Frequency Electromagnetic Field	10V/m, 80 KHz…1 GHz 3V/m, 1.4 GHz…2.0 GHz 1V/m, 2.0 GHz…2.7 GHz
	Fast Transient	2 kV (Power) 2 kV (PE) 1 kV (Communications and control)
	Surge Transient	1 kV (12) L-L, 2 kV (2) L-N (earth)
Standards Compliance		UL 508C; CSA C22.2, No. 14; EN50178; EN61800-3; EN/IEC 60947-4-2; CE Marked per Low Voltage 2006/95/EC; EMC Directive 2004/108/EC; CCC; ODVA for EtherNet/IP; ODVA for DeviceNet
Certifications		cULus (File No. E207834, Guide NMMS, NMMS7)

ArmorPoint and DeviceNet Versions — Control and I/O Power Requirements
	Units	No Options			Brake or Output Contactor			With Brake and Output Contactor
Control Voltage	Volts	24V DC	120V AC	240V AC	24V DC	120V AC	240V AC	24V DC	120V AC	240V AC
Total Control VA (Pick Up)	VA (W)	(11 W)	16	24	(13 W)	38	46	(16 W)	60	68
Total Control VA (Hold In)	VA (W)	(11 W)	16	24	(13 W)	20	28	(16 W)	24	32
External Devices powered by Control Voltage
Outputs (2) (1 A max. each)	Amps	2	2	2	2	2	2	2	2	2
Total Control VA (Pick Up) with max. outputs	VA (W)	(59 W)	256	504	(61 W)	278	548	(64 W)	300	548
Total Control VA (Hold In) with max. outputs	VA (W)	(59 W)	256	504	(61 W)	261	512	(64 W)	264	512

		UL/NEMA	IEC
Input Ratings	Rated Operation Voltage	24V DC
	Input On-State Voltage Range	10…26V DC
	Input On-State Current	3.0 mA @ 10V DC
		7.2 mA @ 24V DC
	Input Off-State Voltage Range	0…5V DC
	Input Off-State Current	<1.5 mA
	Input Filter — Software Selectable
	Off to On	Settable from 0…64 ms in 1 ms increments
	On to Off	Settable from 0…64 ms in 1 ms increments
	Input Compatibility	N/A	IEC 1+
	Number of Inputs	4
	Sensor Source
	Voltage Status Only	11…25V DC from DeviceNet
	Current Available	50 mA max. per input, 200 mA total
Output Ratings Sourced from control circuit - A1/A2	Rated Operation Voltage	240V AC/30V DC	240V AC/30V DC
	Rate Insulation Voltage	250V	250V
	Dielectric Withstand	1500V AC	2000V AC
	Operating Frequency	50/60 Hz
	Type of Control Circuit	Electromechanical relay
	Type of Current	AC/DC
	Conventional Thermal Current Ith	Total of both outputs £ 2 A
	Type of Contacts	Normally open (N.O.)
	Number of Contacts	2
DeviceNet Specifications	DeviceNet Supply Voltage Rating	Range 11…25V DC, 24V DC nominal
	DeviceNet Input Current	167 mA @ 24V DC - 4.0 W
	DeviceNet Input Current	364 mA @ 11V DC - 4.0 W
	External Devices powered by DeviceNet	Sensors inputs 4 x 50 mA - total 200 mA
	Total w/max Sensor Inputs (4)	367 mA @ 24V DC - 8.8 W
	DeviceNet Input Current Surge	15 A for 250 ms
DeviceNet Communications	Baud Rates	125, 250, 500 kbps
	Distance Maximum	500 m (1630 ft) @ 125 kbps
	Distance Maximum	200 m (656 ft) @ 250 kbps
	Distance Maximum	100 m (328 ft) @ 500 kbps
ArmorPoint Ratings	Backplane Current Load	400 mA

EtherNet/IP Version - Control and I/O Power Requirements
Control Voltage	Units	A1/A2⋆	A3/A2‡	A3/A2§
	Volts	24V DC
Current	Amps	0.375	0.125	0.35
Total Control Power (no options)	Watts	9	3	8.4
Total Control Power (with Dynamic Brake or Output Contactor option)	Watts	12	3	8.4
Total Control Power (with Dynamic Brake and Output Contactor option)	Watts	15	3	8.4
⋆ Add power requirements for outputs (1 A max.) to A1/A2.
‡ Add power requirements for intputs (200 mA max.) to A3/A2.
§ If A1 power is disconnected.

		UL/NEMA	IEC
Input Ratings Sourced from control circuit - A3/A2	Rated Operation Voltage	24V DC
	Input On-State Voltage Range	10…26V DC
	Input On-State Current	3.0 mA @ 10V DC
		7.2 mA @ 24V DC
	Input Off-State Voltage Range	0…5V DC
	Input Off-State Current	<1.5 mA
	Input Filter — Software Selectable
	Off to On	Settable from 0…64 ms in 1 ms increments
	On to Off	Settable from 0…64 ms in 1 ms increments
	Input Compatibility	N/A	IEC 1+
	Number of Inputs	4
	Sensor Source
	Voltage Status Only	11…26.4V DC from DeviceNet
	Current Available	50 mA max. per input, 200 mA total
Output Ratings Sourced from control circuit - A1/A2	Rated Operation Voltage	26.4V DC
	Rate Insulation Voltage	250V
	Dielectric Withstand	1500V AC (UL)	2000V AC (IEC)
	Type of Control Circuit	Solid state sourcing output
	Type of Current	24V DC
	Conventional Thermal Current Ith	0.5 A each, 1 A max. combined
	Type of Contacts	Normally open (N.O.)
	Number of Contacts	2
	Load Types	Resistive or light inductive
	Surge Suppression	Integrated diode, clamps @ 35V DC
	Thermo-Protection	Integrated short circuit and over current protection
	Maximum Cycle Rate	30 operations/minute capacitive and inductive loads
	Maximum Blocking Voltage	35V DC
	Maximum On-State Voltage @ Maximum Output	1.5V DC
	Maximum Off-State Leakage Current	10 mA
Device Level Ring (DLR)		Beacon-based performance including IEEE 1588 end to end transparent clock
	Maximum Nodes	50
	Fault Recovery	Ring recovery time is less than 3 ms for a 50 node network
EtherNet Port		2 D-coded, 4-pin female M12 connecters
	Ports	Embedded switch with 2 ports
	IP Address	DHCP enabled by default
	DHCP Timeout	30 seconds
	Communication Rate	10/100 Mbs with auto negotiate half duplex and full duplex
	Data	Transported over both TCP and UDP Min. of 500 I/O packets/second (pps) Supports up to 150 concurrent TCP sockets
Web Server		Embedded web server
	Security	Login and password configurable
	E-mail	Support Simple Mail Transfer Protocol (SMTP)
	Configuration	Status, diagnostics, and configuration tabs
Device Connections		Supports scheduled (Class 1) and unscheduled (Class 3 & UCMM) connections
		6 - Class 3 connections are supported simultaneously
		Minimum of 1 - Class 1 or maximum of 2 - Class 1, CIP connections (1 exclusive owner, 1 input only and 1 listen only) are supported
		Class 1 Connection API: 2…3200 ms Class 3 Connection API: 100…10 000 ms
		20 ms Request Packet Interval (RPI) default
		3 concurrent Encapsulation sessions
		TCP port supports 5 concurrent incoming connections

Drive Characteristics	Sensorless Vector Performance	Sensorless Vector Control
Maximum Hp (kW)/ Input Voltage	2 Hp (1.5 kW)/230V AC 5 Hp (3.3 kW)/480V AC	2 Hp (1.5 kW)/230V AC 5 Hp (3.3 kW)/480V AC, 5 Hp (4.0 kW)/600V AC
Overload Capacity	150% for 60 seconds, 200% for 3 seconds	150% for 60 seconds, 200% for 3 seconds
Output Frequency (programmable)	0…400 Hz	0…400 Hz
Efficiency (typical)	97.5%	97.5%
Preset Speeds	4	8
Carrier Frequency	2…16 kHz	2…16 kHz
Skip Frequency	—	ü
Process Control Loop	—	ü (PID)
StepLogic Functionality	—	ü
Timer/Counter Functions	—	ü

Drive Ratings — VFD Output Current vs. Input Current
Line Voltage	Frequency [Hz]	3-Phase kW Rating	3-Phase Hp Rating	Output Current [A]		Input Current [A]
				Sensorless Vector Control	Sensorless Vector Performance	Sensorless Vector Control	Sensorless Vector Performance
200	50	0.4	—	2.3	—	3.65	—
		0.75	—	4.5	—	6.40	—
		1.5	—	7.6	—	10.65	—
230	60	—	0.5	2.3	2.3	3.10	2.5
		—	1	4.5	4.5	5.70	5.2
		—	2	7.6	7.6	9.45	9.5
380	50	0.4	—	1.4	—	2.15	—
		0.75	—	2.3	—	3.80	—
		1.5	—	4.0	—	6.40	—
		2.2	—	6.0	—	9.00	—
		3.0	—	7.6	—	12.40	—
460	60	—	0.5	1.4	1.4	1.85	1.8
		—	1	2.3	2.3	3.45	3.2
		—	2	4.0	4.0	5.57	5.7
		—	3	6.0	6.0	8.20	7.5
		—	5	7.6	7.6	12.5	8.6
575	60	—	1	1.7	—	2.78	—
		—	2	3.0	—	4.73	—
		—	3	4.2	—	6.64	—
		—	5	6.6	—	10.75	—

Protective Specifications — Sensorless Vector Performance
Motor Protection	I2t overload protection — 150% for 60 seconds, 200% for 3 seconds (provides Class 10 protection)
Overcurrent	200% hardware limit, 300% instantaneous fault
Over Voltage	200…240V AC Input — Trip occurs @ 405V DC bus voltage (equivalent to 290V AC incoming line) 380…460V AC Input — Trip occurs @ 810V DC bus voltage (equivalent to 575V AC incoming line)
Under Voltage	200…240V AC Input — Trip occurs @ 210V DC bus voltage (equivalent to 150V AC incoming line) 380…480V AC Input — Trip occurs @ 390V DC bus voltage (equivalent to 275V AC incoming line)
Faultless Power Ride Through	100 milliseconds

Control Specifications — Sensorless Vector Performance
Carrier Frequency	2…16 kHz drive rating based on 4 kHz
Frequency Accuracy — Digital Input	within ±0.05% of set output frequency
Speed Regulation (open loop with slip compensation)	±2% of base speed across a 40:1 speed range
Stop Modes	Multiple programmable stop modes including: Ramp, Coast, DC-Brake, Ramp-to-Hold, and S Curve
Acceleration/Deceleration	Two independently programmable acceleration and deceleration times: each time may be programmed from 0…600 seconds in 0.1 second increments
Intermittent Overload	150% overload capability for up to 1 minute, 200% overload capability for up to 3 seconds
Electronic Motor Overload Protection	Class 10 protection with speed sensitive response and power-down overload retention function

Sensorless Vector Performance (SVP) Minimum DB Resistance
Input Voltage	Drive Rating [kW]	Drive Rating [Hp]	Minimum DB Resistance [W]
200…240V, 50/60 Hz, Three-Phase	0.2	0.25	60
	0.4	0.5	60
	0.75	1	60
	1.5	2	60
480V, 50/60 Hz, Three-Phase	0.4	0.5	121
	0.75	1	121
	1.5	2	121
	2.2	3	97
	3.7	5	97

Protective Specifications — Sensorless Vector Control
Motor Protection	I2t overload protection — 150% for 60 seconds, 200% for 3 seconds (provides Class 10 protection)
Overcurrent	200% hardware limit, 300% instantaneous fault
Over Voltage	200…240V AC Input – Trip occurs @ 405V DC bus voltage (equivalent to 290V AC incoming line) 380…460V AC Input – Trip occurs @ 810V DC bus voltage (equivalent to 575V AC incoming line) 460…600V AC Input – Trip occurs @ 1005V DC bus voltage (equivalent to 711V AC incoming line)
Under Voltage	200…240V AC Input – Trip occurs @ 210V DC bus voltage (equivalent to 150V AC incoming line) 380…480V AC Input – Trip occurs @ 390V DC bus voltage (equivalent to 275V AC incoming line) 460…600V AC Input – If 600V rated trip occurs @ 487V DC bus voltage (344V AC incoming line); If 480V rated trip occurs @ 390V DC bus voltage (275V AC incoming line)
Faultless Power Ride Through	100 milliseconds

Control Specifications — Sensorless Vector Control
Carrier Frequency	2…16 kHz drive rating based on 4 kHz
Frequency Accuracy — Digital Input	within ±0.05% of set output frequency
Speed Regulation (open loop with slip compensation)	±1% of base speed across a 60:1 speed range
Stop Modes	Multiple programmable stop modes including: Ramp, Coast, DC-Brake, Ramp-to-Hold, and S Curve
Acceleration/Deceleration	Two independently programmable acceleration and deceleration times: each time may be programmed from 0…600 seconds in 0.1 second increments
Intermittent Overload	150% overload capability for up to 1 minute, 200% overload capability for up to 3 seconds
Electronic Motor Overload Protection	Class 10 protection with speed sensitive response

Sensorless Vector Control (SVC) Minimum DB Resistance
Drive Rating			Minimum DB Resistance
Input Voltage	[kW]	[Hp]	[W]
240V, 50/60 Hz, Three-Phase	0.4	0.5	48
	0.75	1	48
	1.5	2	48
480V, 50/60 Hz, Three-Phase	0.4	0.5	97
	0.75	1	97
	1.5	2	97
	2.2	3	97
	4.0	5	77
600V, 50/60 Hz, Three-Phase	0.75	1	120
	1.5	2	120
	2.2	3	82
	4.0	5	82

Motor Overload Trip Curves

Motor overload current parameter provides class 10 overload protection. Ambient insensitivity is inherent in the electronic design of the overload.


Approximate Dimensions

Dimensions for IP67/NEMA Type 4 with Conduit Entrance

Dimensions in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes. All dimensions are subject to change.



Dimensions for NEMA Type 4X with Conduit Entrance

Dimensions in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes. All dimensions are subject to change.



Dimensions for IP67/NEMA Type 4 with ArmorConnect Connectivity

Dimensions in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes. All dimensions are subject to change.



Dimensions for NEMA Type 4X with ArmorConnect Connectivity (1 Hp or less @ 230V AC and 2 Hp or less @ 480…575V AC)

Dimensions in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes. All dimensions are subject to change.



Dimensions for NEMA Type 4X with ArmorConnect Connectivity (2 Hp or greater @ 230V AC and 3 Hp or greater @ 480…575V AC)

Dimensions in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes. All dimensions are subject to change.