Distributed Starters (Networked)

Catalogs > Industrial Controls Catalog > Motor Control, Solid-State > Distributed Starters (Networked) > Bulletin 283 ArmorStart Distributed Motor Controller

Bulletin 283 ArmorStart Distributed Motor Controller

Specifications

Connections

Bulletin 283D ArmorStart with DeviceNet Communications



Bulletin 283A ArmorStart for the ArmorPoint Backplane



Bulletin 283 ArmorStart Power and Control Terminals

Terminal Designations	Number of Poles	Description
SM1⋆	2	Safety Monitor Input
SM2⋆	2	Safety Monitor Input
A1 (+)	2	Control Power Input
A2 (-)	2	Control Power Common
PE	2	Ground
1/L1	2	Line Power Phase A
3/L3	2	Line Power Phase B
5/L5	2	Line Power Phase C
⋆ Only available with the Safety Monitor option.

ArmorStart Receptacle Pin Outs

Receptacle Connections for ArmorPoint Interface (OUT)

Pin 1: CAN high Pin 2: Common Pin 3: +5V Pin 4: CAN low Pin 5: Enable out Pin 7: Common Pin 8: NC (no connection)

Receptacle Connections for ArmorPoint Interface (IN)

Pin 1: CAN high Pin 2: Common Pin 3: +5V Pin 4: CAN low Pin 5: Enable out Pin 7: Common Pin 8: PE

Receptacle Connections for DeviceNet Connector

Pin 1: Drain (no connection) Pin 2: +VDNET Pin 3: -VDNET Pin 4: CAN_H Pin 5: CAN_L

Receptacle Connections for Input (M12)

Pin 1: +24V (A3 or DNET) Pin 2: Input 0 Pin 3: Common Pin 4: Input 1 Pin 5: NC (no connection)

Receptacle Connections for Output, DeviceNet or ArmorPoint Version (M12)

Pin 1: PE Pin 2: Return Pin 3: Relay out

Receptacle Connections for Incoming Control Power

Pin 1: Unswitched (A3)(red) Pin 2: Common (A2)(black) Pin 3: PE (green) Pin 4: Not used (blank) Pin 5: Switched (A1)(blue) Pin 6: Not used (white)

Receptacle Connections for Source Brake

Pin 1: L1 (black) Pin 2: GND (green/yellow) Pin 3: L2 (white)

Receptacle Connections for Motor Connector -
5 Hp or less (M22)

Pin 1: T1 (black) Pin 2: T2 (white) Pin 3: T3 (red) Pin 4: Ground (green/yellow)

Receptacle Connections for Motor Connector -
10 Hp (M35)

Pin 1: T1 (black) Pin 2: Ground (green/yellow) Pin 3: T3 (red) Pin 4: T2 (white)

Receptacle Connections for Incoming 3-phase Power -
10 A Short Circuit Protection (M22)

Pin 1: L1 (black) Pin 2: L2 (white) Pin 3: L3 (red) Pin 4: Ground (green/yellow)

Receptacle Connections for Incoming 3-phase Power -
25 A Short Circuit Protection (M35)

Pin 1: L1 (black) Pin 2: Ground (green/yellow) Pin 3: L3 (red) Pin 4: L2 (white)

Motor Overload Trip Curves

Motor overload current parameter provides class 10 overload protection. Ambient insensitivity is inherent in the electronic design of the overload.

Electrical Ratings		UL/NEMA			IEC
Power Circuit	Rated Operation Voltage	200…575Y			200…575V
	Rate Insulation Voltage	600V			500V
	Rated Impulsed Voltage	6 kV			6 kV
	Dielectric Withstand	2200V AC			2500V AC
	Operating Frequency	50/60 Hz			50/60 Hz
	Utilization Category	N/A			AC-3
	Protection Against Shock	N/A			IP2X
	Rated Operating Current Max.	280_-___-10A-*	3.0 A
		280_-___-10B-*	5.5 A
		280_-___-10C-*	7.6 A
		280_-___-10D-*	16 A
Control Circuit	Rated Operation Voltage	24V DC (+10%, -15%) A2 (should be grounded at voltage source)
		120V AC (+10%, -15%) A2 (should be grounded at voltage source)
		240V AC (+10%, -15%) A2 (should be grounded at voltage source)
	Rated Insulation Voltage	250V			250V
	Rated Impulsed Voltage	—			4 kV
	Dielectric Withstand	1500V AC			2000V AC
	Overvoltage Category	—			III
	Operating Frequency	50/60 Hz
Short Circuit Protection	SCPD Performance Type 1	Current Rating	Voltage	480Y/277V	480Y/480V	600Y/347V	600V
		1.1…3.0 A	Sym. Amps RMS	65 kA	65 kA	30 kA	30 kA
		3.0…5.5 A
		5.3…7.6 A
		6.3…16 A		30 kA	30 kA	30 kA	30 kA
	SCPD List	Size per NFPA 70 (NEC) or NFPA 79 for Group Motor Applications

Power Requirements
	Units
Control Voltage (Nom)	Volts	24V DC	120V AC	240V AC
Power supply (Nom)	Amps	0.170	0.110	0.060
Total Control Power (Starting/Stopping)	VA (W)	(90 W)	35	35
Total Control Power (Running)	VA (W)	(8 W)	28	28
External Devices powered by Control Voltage
Outputs (2) (1 A max. each)	Amps	2	2	2
Total Control (Pick Up) with max outputs	VA (W)	(138 W)	275	515
Total Control (Hold In) with max outputs	VA (W)	(56 W)	268	508

Input Ratings	Rated Operation Voltage	24V DC
	Rated Insulation Voltage	1500V AC
	Input On-State Voltage Range	10…26V DC
	Input On-State Current	3.0 mA @ 10V DC
		7.2 mA @ 24V DC
	Input Off-State Voltage Range	0…5V DC
	Input Off-State Current	<1.5 mA
	Input Filter — Software Selectable
	Off to On	Settable from 0…64 ms in 1 ms increments
	On to Off	Settable from 0…64 ms in 1 ms increments
	Input Compatibility	N/A	IEC 1+
	Number of Inputs	4
	Sensor Source
	Voltage Status Only	11…25V DC from DeviceNet
	Current Available	50 mA max. per input, 200 mA total
Output Ratings (Sourced from Control Circuit)	Rated Operation Voltage	250V AC/30V DC	250V AC/30V DC
	Rated Insulation Voltage	250V	250V
	Dielectric Withstand	1500V AC	2000V AC
	Operating Frequency	50/60 Hz	50/60 Hz
	Type of Control Circuit	Electromechanical relay
	Type of Current	AC/DC
	Conventional Thermal Current Ith	Total of both outputs £ 2 A
	Type of Contacts	Normally open (N.O.)
	Number of Contacts	2

		UL/NEMA	IEC
Environmental	Operating Temperature Range	-20…+40 °C (-4…+104 °F)
	Storage and Transportation temperature range	–25….+85 °C (–13…+185 °F)
	Altitude	2000 m
	Humidity	5…95% (non-condensing)
	Pollution Degree	3
	Enclosure Ratings	NEMA 4/12/13	IP67
	Enclosure Ratings	NEMA 4X	IP69K
	Approximate Shipping Weight	16.8 kg (37 lb)
Mechanical	Resistance to Shock
	Operational	15 G
	Non-Operational	30 G
	Resistance to Vibration
	Operational	1 G, 0.15 mm (0.006 in.) displacement
	Non-Operational	2.5 G, 0.38 mm (0.015 in.) displacement
	Power and Ground Terminals
	Wire Size	Primary/Secondary terminal: (#16 …#10 AWG)	Primary/Secondary terminal: 1.5…4.0 mm2
	Tightening Torque	Primary terminal: 10.8 lb•in Secondary terminal: 4.5 lb•in	Primary terminal: (1.2 N•m) Secondary terminal: (0.5 N•m)
	Wire Strip Length	0.35 in. (9 mm)
	Control and Safety Monitor Inputs
	Wire Size	(18…10 AWG)	1.0…4.0 mm2
	Tightening Torque	6.2 lb•in	0.7 N•m
	Wire Strip Length	0.35 in. (9 mm)
	Disconnect Lock Out	Maximum of 5/16 in. (8 mm) lock shackle or hasp. The hasp should not exceed 5/16 in. (8 mm) when closed, or damage will occur to disconnect guard.
Other Rating	EMC Emission Levels
	Conducted Radio Frequency Emissions	Class A
	Radiated Emissions	Class A
	EMC Immunity Levels
	Electrostatic Discharge	4 kV contact and 8 kV Air
	Radio Frequency Electromagnetic Field	10V/m
	Fast Transient	2 kV
	Surge Transient	1 kV (12) L-L, 2 kV (2) L-N (earth)
	Overload Characteristics
	Overload Current Range	1.1…3.0 A
		3.0…5.5 A
		5.3…7.6 A
		6.3…16 A
	Trip Class	10
	Trip Rating	120% of FLC setting
	Number of Poles	3
	DeviceNet Specifications
	DeviceNet Supply Voltage Rating	Range 11…25V DC, 24V DC nominal
	DeviceNet Input Current	167 mA @ 24V DC - 4.0 W
		364 mA @ 11V DC - 4.0 W
	External Devices powered by DeviceNet	Sensors inputs 4 x 50 mA - total 200 mA
	Total w/max Sensor Inputs (4)	367 mA @ 24V DC - 8.8 W
	DeviceNet Input Current Surge	15 A for 250 ms
	DeviceNet Communications
	Baud Rates	125, 250, 500 kbps
	Distance Maximum	500 m (1630 ft) @ 125 kbps
		200 m (656 ft) @ 250 kbps
		100 m (328 ft) @ 500 kbps
	ArmorPoint Backplane Current Load	400 mA
Standards Compliance		UL 508; CSA C22.2, No. 14; EN/IEC 60947; EN/IEC 60947-1; CE Marked per Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC; CCC; ODVA for DeviceNet
Certifications		cULus (File No. E96956, Guides NMFT, NMFT7)