Catalogs > Industrial Controls Catalog > Relays, Timers, and Temperature Controllers > General Purpose Relays > Bulletin 700-HA Tube Base Relay
Bulletin 700-HA Tube Base Relay
| Introduction |  |
Standards Compliance and Certifications | |
Product Selection | |
Accessories | |
Specifications | |
Approximate Dimensions | |
| Description | Pkg. Qty. | Cat. No. | |
|
Screw Terminal Tube Base Socket — Panel or DIN Rail Mounting; Guarded Terminal Construction. 8-Pin for use with DPDT Bulletin 700-HA Relays, -HX Timing Relays, -HT (On-Delay) and -HRM, -HRC and -HV (Repeat Cycle) Timing Relays. | 10 | 700-HN100 |
| Cat. No. 700-HN100 | |||
|
Screw Terminal Tube Base Socket — Panel or DIN Rail Mounting; Open Style Construction. 8-Pin for use with DPDT Bulletin 700-HA Relays, -HT (On-Delay) and -HRM, -HRC, and -HV (Repeat Cycle) Timing Relays. No retainer clip required. | 10 | 700-HN125 |
| Cat. No. 700-HN125 | |||
|
Screw Terminal Tube Base Sockets — Panel or DIN Rail Mounting; Guarded Terminal Construction. 11-pin for use with 3PDT 700-HA relays. | 10 | 700-HN101 |
| Cat. No. 700-HN101 | |||
|
Screw Terminal Tube Base Sockets — Panel or DIN Rail Mounting; Open Style Terminal Construction. 11-pin for use with 3PDT 700-HA relays. No retainer clip required. | 10 | 700-HN126 |
| Cat. No. 700-HN126 | |||
|
8-Pin Socket — Can Be Used With or Without Timing Attachment or Surge Suppressor Screw Terminal Tube Base Sockets — panel or DIN Rail mounting. Guarded terminal construction. Used with DPDT Bulletin 700-HA Relays. |
10 | 700-HN204 |
| 11-Pin Socket — Can Be Used With or Without Timing Module or Surge Suppressor. Screw Terminal Tube Base Sockets — panel or DIN Rail mounting. Guarded terminal construction. Used with 3PDT Bulletin 700-HA relays. |
10 | 700-HN205 | |
| Cat. No. 700-HN205 | |||
|
DIN (#3) symmetrical hat rail 35 x 7.5 x 1 m |
10 | 199-DR1 |
| Cat. No. 199-DR1 | |||
| Description | Pkg. Qty. | Cat. No. | |||
|
Diode Surge Suppressor⋆ Voltage Range: 6…220V DC used with 700-HN204 and 700-HN205 socket |
10 | 700-ADR | ||
| Diode with LED Surge Suppressor⋆ Voltage Range: 6…24V DC used with 700-HN204 and 700-HN205 socket |
10 | 700-ADL1R | |||
| Diode with LED Surge Suppressor⋆ Voltage Range: 28…60V DC used with 700-HN204 and 700-HN205 socket |
10 | 700-ADL2R | |||
| Diode with LED Surge Suppressor⋆ Voltage Range: 110…220V DC used with 700-HN204 and 700-HN205 socket |
10 | 700-ADL3R | |||
| Varistor with LED Surge Suppressor⋆ Voltage Range: 6…24V AC used with 700-HN204 and 700-HN205 socket |
10 | 700-AV1R | |||
| Varistor with LED Surge Suppressor⋆ Voltage Range: 110…240V AC used with 700-HN204 and 700-HN205 socket |
10 | 700-AV3R | |||
| RC Surge Suppressor⋆ Voltage Range: 6…24V AC/DC used with 700-HN204 and 700-HN205 socket |
10 | 700-AR1 | |||
| RC Surge Suppressor⋆ Voltage Range: 110…240V AC/DC used with 700-HN204 and 700-HN205 socket |
10 | 700-AR2 | |||
|
Timing Module On-Delay or One-Shot selectable voltage range: 12…24V AC/DC used with sockets that accept plug-in accessory modules. |
|
1 | 700-AT3 | |
| Timing Module On-Delay or One-Shot selectable voltage range: 110…125V AC used with sockets that accept plug-in accessory modules. |
700-AT3A1 | ||||
| Timing Module On-Delay or One-Shot selectable voltage range: 230…240V AC used with sockets that accept plug-in accessory modules. |
700-AT3A2 | ||||
|
Multi-Function Multi-Range Time Module⋆ Voltage range 12…240V AC 50/60 Hz and 12…240V DC, with a voltage variation of 85…110%. Repeat accuracy of ±1%. Reset time <50 ms. Refer to Specifications for Specifications. |
1 | 700-HT3 | ||
| Eight Timing Modes Seven Timing Ranges as follows: |
|||||
| 1. 1 s | 0.05 s…1 s |
|
|||
| 2. 10 s | 0.5 s…10 s |
|
|||
| 3. 100 s | 5 s…100 s |
|
|||
| 4. 10 min | 0.5 min…10 min |
|
|||
| 5. 100 min | 5 min…100 min |
|
|||
| 6. 10 hours | 0.5 h…10 h |
|
|||
| 7. 100 hours | 5 h…100 h |
|
|||
| Cat. No. 700-HT3 | 8. LED Indicator | ||||
| ⋆ Suppressors and Time Modules easily plug into sockets (Cat. Nos. 700-HN204 and 700-HN205). For use with Bulletin 700-HA relays. | |||||
ATTENTION: Cat. No. 700-HT3 is wired with signal “S” connected to “A1”. See wiring diagram marked on the timer module.
| Description | Pkg. Qty. | Cat. No. | |
|
Retainer Clip for Cat. Nos. 700-HN100, -HN101, -HN204, and -HN205 Sockets with Bulletin 700-HA Relays⋆ Secures relay in socket. |
10 | 700-HN157 |
| Sample Retainer Clips | |||
|
Relay Identification Snap-in Markers§ Snap-in markers fit on top of product covers. Squares slip into molded slot on top of product cover. |
5 | 1492-MS5X12 |
| 1492-MS6X9 | |||
| 1492-MS6X12 | |||
| 1492-MS8X9 | |||
| 1492-MS8X12 | |||
| 1492-MP-Blank | |||
| Snap-in markers | |||
|
Pre-Printed Identification Tags — contains 10 sheets of pre-printed and blank tags. Each sheet contains 13 sets of the markings CR…9CR, TR…9TR, M…9M, F, R, 1S, and 117 blank tags. Tags are peel-off with sticky backing for easy placement on relays. | 10 | 700-N40 |
| Blank Identification Tags — contains 10 sheets of blank identification tags for customer specialized printing. Each sheet contains 546 blank tags. Tags are peel-off with sticky backing for easy placement on relays. | 10 | 700-N41 | |
| ⋆ See Bulletin 700-HA Relay, Socket, and Retainer Clip Reference Chart below. | |||
| § For pre-printed marker cards, turn to the following 1492 sections (tab 12, under IEC Terminal Block Accessories): 1492-SM5X12_, 1492-SM6X9_,1492-SM8X9_,1492-SM8X12_,1492-MP_. | |||
| Relay Type | Socket | Retainer Clip |
| 700-HA32 700-HAB2 700-HAX2 |
700-HN100 700-HN125 700-HN204 700-HN200 |
700-HN157 Not Required♣ 700-HN157 700-HN157 |
| 700-HA33 700-HAB3 700-HAX3 |
700-HN201 700-HN101 700-HN126 700-HN205 |
700-HN157 700-HN157 Not Required♣ 700-HN157 |
| ♣ Design of these sockets holds the relays securely and does not require retainer clips. | ||