Bulletin 700-HX Multifunction Digital Timing Relay
| Product Overview |
|
Bulletin 700-HX
- Digital timing relay with LCD display
- Socket- or panel-mounted (NEMA 4X/IP66)
- 5A, B300, SPDT contact ratings
- 10 Functions or modes
- Environmentally friendly — flash memory, no battery
- User Manual 700-UM002_-EN-D available at Literature Library
Standards Compliance and Certifications
See Specifications.
Product Selection
| Build a Catalog Number |
| Model | Operating Mode | Timing Range | Socket Type | Contact Output | No. of Pins | Input Voltage | Cat. No. |
|
A mode: Signal On-Delay 1 A-1 mode: Signal On-Delay 2 A-2 mode: Power On-Delay 1 A-3 mode: Power On-Delay 2 B mode: Repeat Cycle 1 B-1 mode: Repeat Cycle 2 D mode: Signal OFF-delay E mode: One Shot F mode: Cumulative Twin Timer |
0.000…9.999 s 0.000…99.99 s 0.000…999.9 s 0.000…9999 s 0.000…99 min 59 s 0.000…999.9 min 0.000…9999 min 0.000…99 hr 59 min 0.000…999.9 hr 0.000…9999 hr |
700-HN100 700-HN125 |
SPDT | 8 | 100…240V AC | 700-HX86SA17 |
| Cat. No. 700-HX… | 24V AC 12…24V DC |
700-HX86SU24 | |||||
General Timer Functions
|
Accessories
| Description | Pkg. Quantity | Cat. No. | |
|
Screw Terminal Tube Base Socket — Panel or DIN Rail Mounting; Guarded Terminal Construction. 8-Pin for use with Bulletin 700-HX Timing Relays. Order ten or multiples of ten | 10 | 700-HN100 |
| Cat. No. 700-HN100 | |||
|
Screw Terminal Tube Base Socket — Panel or DIN Rail Mounting; Open Style Construction. 8-Pin for use with Bulletin 700-HX Timing Relays. Order must be for 10 sockets or multiples of 10. No retainer clip required. | 10 | 700-HN125 |
| Cat. No. 700-HN125 | |||
|
DIN (#3) Symmetrical Rail 35 x 7.5 x 1 m |
10 | 199-DR1 |
| Cat. No. 199-DR1 | |||
|
Specialty Socket 8-pin backwired socket with solder terminals. For use with 700-HX Timing Relays. |
10 | 700-HN108 |
| Cat. No. 700-HN108 | |||
|
Retainer Clip for Cat. Nos. 700-HN100 Sockets with all 700-HX Timing Relays Secures timer in socket. Note: Not required for installation |
10 | 700-HN131 |
| Sample Retainer Clips | |||
|
Frame Adapter For flush or door mounting of all Bulletin 700-HR and -HX timers. |
1 | 700-HN130 |
| Cat. No. 700-HN130 | |||
|
Protective Cover Helps prevent tampering of timing and mode settings. Provides a degree of protection against water and dirt from entering the front of the relay. For use with all Bulletin 700-HRs and -HX timing relays. |
1 | 700-HN132 |
| Cat. No. 700-HN132 | |||
| Timing Relay, Socket, Retainer Clip Reference Chart | ||
| Timer Type | Socket Cat. No. | Retainer Clip Cat. No. |
| 700-HX | 700-HN100 | 700-HN131 |
| 700-HN108 | Not Required¬ | |
| 700-HN125 | Not Required¬ | |
| ¬ Design of socket holds the relay securely and does not require retainer clips. | ||
Specifications
| Electrical Ratings | ||
| Pilot Duty Rating | NEMA B300 | |
| Rated supply voltage | 100 to 240V AC, 24V AC/12 to 24V DC (50/60Hz) (permissible ripple: 20%(p-p) max.) | |
| Operating voltage range | 85…110% of rated supply voltage | |
| Power consumption | 100…240V AC | 4.3VA |
| 24V AC/12…24V DC | 3.4VA/1.7 W | |
| Inrush Current | 100…240V AC | 3 A |
| 24V AC/12…24V DC | 5 A | |
|
120V AC | 30 A |
| Make | 240V AC | 15 A |
|
120V AC | 3 A |
| Break | 240V AC | 1.5 A |
| Hp at 120V AC | 1/4 Hp | |
| Hp at 240V AC | 1/3 Hp | |
| Mechanical | ||
| Mounting Method | Flush mounting, surface mounting, DIN mounting | |
| Display | Seven-segment, negative transmissive LCD; Present value (red, 8 mm high characters); Set value (green, 4 mm high characters) | |
| Digits | Four digits | |
| Timer | Time ranges | 0.000…9.999 s, 0.00…99.99 s, 0.0…999.9 s, 0…9999 s, 0 min 00 s…99 min 59 s, 0.0…999.9 min, 0 hr 00 min…99 hr 59 min, 0.0 hr…999.9 hr, 0 hr…9999 hr |
| Timer modes | Elapsed time (Up), remaining time (Down), selectable | |
| Output modes | A, A-1, A-2, A-3, B, B-1, D, E, F, Z, ton or toff | |
| Inputs | Input signals | Start, reset |
| Input method | No-voltage input via:NPN transistor or switching of contact | |
| Start, reset, gate | Minimum input signal width: 1 or 20 ms (selectable) | |
| Power reset | Minimum power-opening time: 0.5 s (Except for A-3, B-1, and F mode) | |
| Control output | SPDT contact output: 5 A at 250V AC, resistive load (cosine=1) Minimum applied load: 10 mA at 5 V DC (failure level: P, reference value) |
|
| External Power Supply | No | |
| Key Protect | Yes | |
| Memory Backup | EEP-ROM (overwritten 200 000 times min), which can store data for 20 years min. | |
| Accuracy of Operating Time and Setting Error¬ | Power-ON start: +-0.01% +-50 ms max. * to be rated against set value Signal start: +- 0.005% +-30 ms max. * to be rated against set value Signal start at transistor output model: +- 0.005% +-3 ms max.T If the set value is within the sensor waiting time (250 ms max.) |
|
| ¬ The values are based on the set value. | ||
| T The value is applied for a minimum pulse width of 1 ms. | ||
| Characteristics¬ | ||
| Insulation Resistance | 100 mW min. (at 500V DC) | |
| Dielectric Strength | 2000V AC, 50/60Hz for 1 min between current-carrying terminals and non-current-carrying metal parts (1000V AC for 24V AC/12 to 24V DC type), 1000 VAC, 50/60 Hz for 1 min between non-continuous contacts | |
| Noise Immunity | '+-1.5 kV (between power terminals) for 100 to 240 VAC, +-480V for 24VAC/12 to 24VDC, and +-600V (between input terminals), square-wave noise by noise simulator (pulse width: 100 ns/1 ms, 1-ns rise) | |
| Static Immunity | ±8 kV (malfunction), ±15 kV (destruction) | |
| Vibration Resistance | Malfunction | 10…55 Hz with 0.35 mm single amplitude each in three directions for 10 min |
| Shock Resistance | Malfunction | 98 m/s2 (approx. 10 G) each in three directions |
| Life Expectancy | Mechanical | 10 million operations min. (under no load at 18 000 operation/hr) |
| Electrical | 100 000 operations min. (5 A at 250V AC, resistive load at 1800 operation/hr) | |
| EMC | (EMI) | EN61812-1 |
| Emission Enclosure: | EN55011 Group1 class A | |
| Emission AC mains: | EN55011 Group1 class A | |
| (EMS) | EN61812-1 | |
| Immunity ESD: | EN61000-4-2: 6 kV contact discharge (level2) 8 kV air discharge (level3) | |
| Immunity RF-interference: | EN61000-4-3: 10 V/m | |
| Enclosure Ratings | Panel surface:IP66 and NEMA Type 4X (indoors)T | |
| Weight | Approx. 100 g | |
| Certifications | CE Certified; cURus (File No. E14843, Guide NRNTZ/NRNT8), C-Tick Marked | |
| Standards | EN61010-1, EN 61326, VDE0106/P 100, CSA C22.2 No. 14, UL 508 | |
| ¬ 700-HX User Manual, pub. number 700-UM002_-EN-D, available at Literature Library. | ||
| T An attached waterproof packing is necessary to ensure IP66 waterproofing between the 700-HX and installation pan. | ||
Timing Charts
|
| Output mode A Mode: Signal ON-Delay (Timer resets when power comes ON.) | |
|
|
| Output Mode A-1: Signal ON-Delay 2 (Timer resets when power comes ON.) | |
|
|
| Output mode A-2: Power ON Delay 1 (Timer resets when power comes ON) | |
|
|
| Output mode A-3 Power ON Delay 2 (Timer does not reset when power comes ON) | |
|
|
| ¬ Gate not included on any mode of this relay. | |
| Output mode B: Repeat Cycle (Timer resets when power comes ON.) | |
|
|
|
|
| Output Mode B-1: Repeat Cycle 2 (Timer does not reset when power comes ON) | |
|
|
|
|
| ¬ Gate not included on any mode of this relay. | |
| Output mode D: Signal OFF-delay (Timer resets when power comes ON.) | |
|
|
| Output mode E: Interval (Timer resets when power comes ON.) | |
|
|
| Output Mode F: Cumulative (Timer does not reset when power comes ON) | |
|
|
| ¬ Gate not included on any mode of this relay. | |
Z Mode
Output quantity can be adjusted by changing the cycle time set in the adjustment level to 1 and by changing the ON duty (%) set value. The set value shows the ON duty (%) and can be set to a value between 0 and 100 (%). When the cycle time is 0, the output will always be OFF. When the cycle time is not 0 and when ON duty has been set to 0 (%), the output will always be OFF. When ON duty has been set to 100 (%), the output will always be ON.
| Z mode: ON/OFF-duty Adjustable Repeat Cycle | |
|
|
| Output mode T OFF: Twin Timer OFF start | |
|
|
| Output mode T ON: Twin Timer ON start | |
|
|
| ¬ Gate not included on any mode of this Relay. | |
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
|
|
Terminal Arrangement
|
