Bulletin 700-FF DIN Rail Timing Relay
| Product Overview |
|
Bulletin 700-FF
- Fixed function and fixed range timing relays
- DIN Rail mounted without cost of socket
- 22.5 mm wide, factory set, non-adjustable
- Available as SPDT or DPDT contact output, 8 A
- Fixed timing setting from 0.1 s...10 hr
Standards Compliance and Certifications
See Specifications.
Catalog Number Explanation
| 700 | – | FF | A | 1 | 025 | M | U24 | |||||
| Bulletin Number | Type of Relay | Operating Mode | Contact Output | Fixed Time Setting | Fixed Time Units | Input Voltage |
| 700–FF | A | 1 | 025 | M | U24 | |||||
| a | b | c | d | e |
| a | |
| Operating Mode | |
| Code | Description |
| A | On-delay |
| B | Off-delay |
| D | One shot |
| F | Flasher (repeat cycle starts with pulse) |
| G | Flasher (repeat cycle starts with pause) |
| b | |
| Contact Output | |
| All functions: | |
| 1 One changeover contact (SPDT) |
1 C/O |
| 2 Two changeover contact (DPDT) |
2 C/O |
| c | d | |
| Timing Setting/Time Units | ||
| Code | Code | Description |
| 025 | S | 2.5 seconds |
| 270 | M | 27.0 minutes |
| 100 | H | 10 hours |
| Third position is decimal point (025S = 2.5 s, 270M = 27.0 m, 100H = 10 H). 001...999 seconds 001...999 minutes 001...100 hours |
||
| e | |
| Input Voltage | |
| Code | Description |
| U24 | 24V AC/DC |
| A18 | 110...240V AC 50/60 Hz |
Accessories
| Description | Pkg. Quantity | Cat. No. | ||
| Relay Identification Snap-in Markers Snap-in markers fit on the front of Bulletin 700-FF timing relays covers. The catalog numbers are blank cards. |
80 | 1492-MS5X9 | ||
| 1492-MS5X12 | ||||
| 1492-MS6X9 | ||||
| 1492-MS6X12 | ||||
| 56 | 1492-MS8X9 | |||
| 1492-MS8X12 | ||||
| Custom | T | |||
|
Panel Mounting Adapter For surface mounting according to drilling plan EN 50 002 |
5 | 199-FSA | |
|
Label Sheet 105 self-adhesive paper labels each, 6 x 17 mm |
10 | 100-FMS | |
| Marking Tag Sheet 160 perforated paper labels each, 6 x 17 mm, to be used with a transparent cover |
10 | 100-FMP | ||
| Transparent Cover To be used with marking tag sheets |
100 | 100-FMC | ||
| Marking Tag Adapters To be used with marking tag: System 1492 W |
100 | ¬ | 100-FMA2 | |
| ¬ Cat. No. 100-FMA2 is only a marking tag carrier. Please refer to the Terminal Block Accessories section of this catalog for appropriate marker cards to be used with this carrier. | ||||
| T Go to http://www.ab.com/software/ and click "Terminal Marking System and WinABMS" to download software for custom cards. Create your custom text, save the file and email the file to your local Rockwell Automation sales office or Allen-Bradley distributor. | ||||
Connection Diagrams
(A) On-Delay
|
(B) Off-Delay (Min. Pulse AC 50 ms…DC 30 ms)
|
(D) One Shot
|
(F) Flasher (Repeat Cycle Starts with Pulse)
|
(G) Flasher (Repeat Cycle Starts with Pause)
|
Cleverly Designed Function Display LED (Green)
|
Specifications
| Time Characteristics (according to VDE 0435, Part 2021) | |
| Setting Accuracy | ±5% of full scale |
| Repeatability | ±0.2% of the setting values |
| Tolerance | Voltage: ±0.001%/%DU Temperature: ±0.025%/°C |
| Supply | |
| Supply Voltages | 24V AC/DC and 110…240V AC, 50/60 Hz |
| Voltage Tolerance | 80%...115% nominal supply voltage |
| Power Consumption | 0.5 W at 24V DC, 9 VA at 240V AC |
| Time Energized | 100% |
| Reset Time | 150 ms |
| Voltage Interruption | £20 ms without reset (supply voltage) |
| Input Impedance | Relay ON: 3K-13K ohms Relay OFF: 0.7K-4K ohms |
| Cable Length (Supply Voltage Control) | Max. 250 m (490 ft) |
| Pulse Control (B1) | |
| Pulse Duration | ³50 ms (AC), ³30 ms (DC) |
| Input Voltage | Supply voltage range |
| Input Current | 1 mA |
| Max. Leakage Current | 400 micro Amps |
| Cable Length | Max. 250 m (800 ft) without parallel load between B1 and A2 Max. 50 m (160 ft) with load (<3 kW) between B1 and A2 |
| Outputs | |
| Contact Type | Relay as changeover switch |
| Dielectric Coil to Contact Withstand Voltage |
5000 V |
| Switching Capacity | Voltage: 400V AC |
| Current Ith (AC-12): 8 A | |
| Power: 2500 VA (AC-12), 500 VA (AC-15) | |
| According to IEC 6047-5-1: | |
| 3 A/400V AC (inductive load, AC 14) | |
| 3 A/240V AC (inductive load, AC 15) | |
| 1 A/24V DC (inductive load, DC 13) | |
| According to UL 508: | |
| 1.5 A/240V AC (B300) | |
| 3 A/120V AC (B300) | |
| Short-Circuit Resistance | 10 A gL |
| Life | Mechanical: 10 million operations |
| Electrical operations: | |
| 4 Mil. at 1 A/250V AC, cos f = 1 | |
| 0.2 Mil. at 6 A/250V AC, cos f = 1 | |
| 1.5 Mil. at 1 A/250V AC, cos f = 0.3 | |
| 0.3 Mil. at 3 A/250V AC, cos f = 0.3 | |
| 0.5 Mil. at 6 A/24V DC, resistive | |
| 2 Mil. at 4 A/24V DC, resistive | |
| 2 Mil. at 0.2 A/230V DC, resistive | |
| 1 Mil. at 0.4 A/24V DC, L/R = 20 ms | |
| 1 Mil. at 0.2 A/110V DC, L/R = 20 ms | |
| 1 Mil. at 0.1 A/230V DC, L/R = 20 ms | |
| State Indicator | 1 LED, combination signal |
| General Data | |
| Insulation Characteristics | 2 kVAC/50 Hz test voltage according to VDE 0435 and 6 kV 1.2/50 ms surge voltage according to IEC 60947-1 between all inputs and outputs |
| EMC/Interference Immunity | Performance of following requirements: Surge capacity of the supply voltage according to IEC 61000-4-5: 4 kV 1.2/50 ms Burst according to IEC 61000-4-4: 4 kV ESD discharge according to IEC 61000-4-2: Contact 8 kV, air 8 kV Immunity according to IEC 61000-4-6: 0.15...80 MHz 10V Electromagnetic RF field according to IEC 61000-4-3: 80...1000 MHz 10 V/m |
| EMC/Emission | Electromagnetic fields according to EN 55 022: 30 MHz...2 GHz class B |
| Safe Isolation | According to VDE 106, part 101 |
| Climatic Withstand | 56 Cycles (24 hr) at 25…40 °C and 95% relative humidity according to IEC 600682-30 and IEC 60068-2-3 |
| Vibration Resistance | 4 g in 3three axes at 10…150 Hz, test FC according to IEC 60068-2-6 |
| Shock Resistance | 50 g according to IEC 60068-2-27 |
| Protection Class | Enclosure:IP 40 Terminal:IP 20 according to IEC 60947-1 |
| Weight | 100 g |
| Ambient Temperature | Open: –25…+55 °C Enclosed: –20…+45 °C Storage: –40…+85 °C |
| Terminals | Screw terminal M3.5 for Number 2 Posidrive, Philips, and slotted screws. Suitable for power screwdriver. Rated tightening torque 8.8 lb.-in. (0.8 N•m, max. 1.2 N•m). Dual-chamber system for terminal cross-sections of 1 x 0.5 mm2…2 x 2.5 mm2 (solid) or stranded 2 x 2.5 mm2 (flexible with sleeve), #20…14 AWG. Finger protection according to VDE 0106. |
| Mounting | Front mounting; For snap-on mounting on 35 mm DIN Rail or screw fixing by adapter and two screws (M4 type) |
| Disposal | Synthetic material without dioxin according to EC/EFTA notification |
| Certifications | cULus Listed, File E14840, Guide NKCR/NKCR7, CE Marked |
| Standards | UL 508, CSA 22.2 No. 14, EN/IEC 60947-1, -5-1 |
¬ See Performance Data.