Panel Connection Systems

Description

Connecting inputs and outputs to an Allen-Bradley PLC is very convenient with Allen-Bradley PanelConnect™ Modules and cables. Unlike conventional methods of:

wiring a number of inputs or outputs on machine devices (sensors and pneumatic valves) through a panel and maintaining the integrity of the enclosure then
wiring the connector to a terminal block then
wiring to the PLC I/O Module or
facing the task of providing a seal on a number of cables entering an enclosure

Using a PanelConnect Module with associated Connection systems, allows connection of up to 32 inputs or outputs directly to a 32 point PLC Input or Output module with convenient pre-built cables and connectors.

Benefits

Simplifies Machine and System Commissioning

Often a machine or system is set up at the manufacturer and then disassembled for shipping to the job site. Many of the input and output connections need to be initially connected, then disconnected for shipment, and then reconnected for final assembly. When connecting through the enclosure, the time needed for the reconnection as well as making correct enclosure seals, and making the correct connection for final assembly can be greatly simplified and costs reduced using the PanelConnect module and Connection systems. Commissioning can be done in hours instead of taking weeks and months.

Enclosure Integrity

The PanelConnect module is a simple system that mounts on the enclosure and creates the correct seal for the entry of the input and output connections. There is no longer a need to spend the additional time to seal the opening where the sensor or output cables enter the enclosure or use custom connectors. This reduces the associated time and wiring errors as well.

Environmental Rating

PanelConnect Modules are rated for the harsh environments of IP65/NEMA Type 1, 4, 4X, and 12. These products bridge the IP20, In Panel environment to the IP65, On Machine environment.

Reduced Wiring Time and Cost

Wiring is completed in a fraction of the time when connecting the “Plug and Play” easy assembly system of PanelConnect modules, Pre-Wired I/O Cables, Distribution Box and Distribution Box Patch Cords when compared to traditional methods. Both standard and specific build-to-order length cables are available, providing the correct length for any panel in a neat, space-efficient wiring solution. Lower wiring costs are possible for OEMs and users because less skilled labor is needed to connect the “Plug and Play” system.

Minimal Repair and Replacement Time

“Plug and Play” PanelConnect and Connection systems are easily field replaceable using threaded secured connectors. These systems support the control system requirement for Minimal Time To Repair.

Simplified Design

Design engineers can simplify their panel drawings by calling out a PanelConnect Module and pre-wired cable instead of having to detail every individual wire and terminal block on their drawings. Simplified panel drawings aid not only the installer but also the end customer who receives the panel.

Reduced Wiring Errors

Wiring system cables are pre-tested to ensure 100% accurate connections and eliminate the need for point-to-point checking of wiring. This reduces the possibility of crossed wires and loose connections between the I/O module and the PanelConnect Module. Even one error in wiring 128 I/O points in a point-to-point system may require a complete check of the wiring. Wiring errors can take several minutes to track down and correct before the panel is ready for startup. When PanelConnect Modules and cables are snapped in place, they fit every time — no need to find the wrong or loose connection, resulting in a much higher rate of success at system startup.

Increased Volume and Productivity

PanelConnect systems can help OEMs and panel builders produce a higher volume of machines. Inter-connected wiring for a wiring system is 60 times faster to install than traditional point-to-point wiring, enabling OEMs and panel builders using PanelConnect System components to build panels faster and produce more machines. Machine segments also can be outsourced as machine segments can be connected via the “Plug and Play” products. Wiring is completed in a fraction of the time when connecting inputs and outputs with the Connection system and the PanelConnect Module as compared to the time required for traditional methods.

Design Flexibility

To develop a cost-effective system, the hardware components must meet the needs of the design engineer. Allen-Bradley products provide the broadest range of PanelConnect modules and cables, as well as flexibility with modularity and system expansion capabilities. Allen-Bradley Wiring Systems deliver a lower life-cycle cost.

Quality-Looking Panels

The pre-wired cables and PanelConnect modules organize the wiring in your panel providing a consistent look. Markers and pre-printed adhesive labels for the terminal wiring neatly identify field-wiring-side connections, which correspond to the I/O module. A large marking area is also available for identifying I/O information on the PanelConnect modules.

Smaller Panel Space

By mounting the PanelConnect modules on the side wall of the enclosure, DIN Rail space is eliminated in the panel when compared to traditional terminal blocks.

Reduced Wire Preparation and Routing

PanelConnect systems eliminate the time and costs associated with stripping and cutting wires. Pre-wired cables eliminate this step altogether. Routing wires is much easier with wiring systems since engineers only have to worry about routing one pre-wired cable versus 20 wires used in the traditional wiring method.

Easier Marking and Labeling

Three markers on the front of the PanelConnect are provided to mark both I/O module and input/output points and Patch Cord cables. Pre-printed, I/O-specific adhesive label strips for quick marking of power supply terminals save labor compared to point-to-point wiring that requires labor-intensive wire markers. No wire labels are required on a pre-wired cable. Voltage Marking rings are provided to note AC and DC PanelConnect modules.

Fewer Parts, Less Inventory, and Lower Carrying Cost

A wiring system involves the PanelConnect module and the cable, versus a terminal block, barrier, a jumper, markers, wires, and swing arms with traditional hardwired systems. Therefore, it requires fewer components and, in turn, less inventory and lower carrying costs.

Compatibility

PanelConnect systems works with other digital and analog Allen-Bradley 1492 Programmable Controller Wiring Systems. PanelConnect systems work with the Allen-Bradley Sensor Connection Systems as well as other leading connection systems manufacturers: Brad Harrison™ - Daniel Woodhead, Crouse Hinds, Lumberg and Turck. PanelConnect supports connector cables for both Mini-Plus and M23 style for Mini and Micro Sensor connectors.

PanelConnect System View

Click to enlarge - SensorDistribution_sm.txt

Typical Configuration

PanelConnect Input and Output Module Overview

¬ Field side connectors for two keyed (4 on 32 point) 10-pin or 12-pin Mini-Plus style connectors or M23 12-pin (not on 32 point) which mate to patchcords of the appropriate style.
T PanelConnect input/output module connector for 16-point input/output module cable.
‡ Pre-wired or I/O ready PanelConnect Module cable.
§ Power supply Connector for Power source input.

Note:All of the digital PanelConnect for input and output products have the following features:

cULus Listed and CE Approved

PanelConnect 32-Point Combination (16 Input, 16 Output) Module Overview

¬ Field side connectors for four keyed 12-pin Mini-Plus style connectors which mate to 12-pin Mini-Plus style patchcords.
T PanelConnect input/output module connector for 16-point input/output module cables.
‡ Pre-wired or I/O ready PanelConnect Module cable.
§ Power supply Connector for Power source input.

Note:All of the digital PanelConnect combination input and output products have the following features:

Click to enlarge - Page 7 bottom right photo.txt

cULus Listed and CE Approved

PanelConnect Input Features

16-Point Input PanelConnect Module with two 10-pin Mini-Plus Connectors

These modules are used with sensor (input) distribution boxes with no LEDs. Each 10-pin Mini-Plus connector mates with a 10-conductor main patch cord that connects to the distribution box. On the field connector, various sensors (including photoelectric sensors and proximity sensors) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the input (sensor) voltage requirements. Up to 16 inputs (sensors) can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable that connects to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. Modules are available in NEMA Type 4 or 4X versions.

16-Point Input PanelConnect Module with two 12-pin Mini-Plus Connectors

These modules are normally used with sensor (input) distribution boxes with LEDs. Each 12-pin Mini-Plus connector mates with a 12-conductor main patch cord that connects to the distribution box. On the field connector, various sensors (including photoelectric sensors and proximity sensors or other inputs) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the input (sensor) voltage requirements. Up to 16 inputs (sensors) can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with cables that connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. Modules are available in NEMA Type 4 or 4X versions.

16-Point Input PanelConnect Module with two 12-pin M23 Connectors

These modules are used with sensor (input) distribution boxes with or without LEDs. Each 12-pin M23 connector mates with a ten-, eleven-, or twelve-conductor main patch cord that connects to the distribution box. On the field connector side, various sensors (including photoelectric sensors and proximity sensors or other inputs) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the sensor voltage requirements. Up to 16 inputs (sensors) can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. Modules are available in NEMA Type 4 or 4X versions.

Click to enlarge - 03019003_1667-32ID1001-Gray

32-Point Input PanelConnect Module with four 10-pin Mini-Plus Connectors

These modules are used with Connection systems without LEDs on the distribution box. Each 10-pin Mini-Plus connector mates with a ten-conductor main patch cord that connects to the distribution box. Additionally on the field connection side, various inputs (sensors) connect with a variety of connector styles. Up to 32 inputs can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. Modules are available in NEMA Type 4 or 4X versions.

Click to enlarge - 03019001_1667-32ID1201-Gray

32-Point Input PanelConnect Module with four 12-pin Mini-Plus Connectors

These modules are used with Connection systems with LEDs on the distribution box. Each 12-pin Mini-Plus connector mates with a 12-conductor main patch cord that connects to the distribution box. Additionally on the field connection side, various inputs (sensors) connect with a variety of connector styles. Up to 32 inputs can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. Modules are available in NEMA Type 4 or 4X versions.

Digital Pre-Wired Cables

Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Pre-wired cables, when used with a PanelConnect Module replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The pre-wired cables have a removable terminal block or wiring arm at the I/O end of the cable and a cable connector on the other end to connect to the PanelConnect Module. All of the pre-wired cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection every time. The digital pre-wired cables are offered in four standard lengths of 0.5, 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. Pre-wired cables are available for many of the 1746 SLC I/O, 1756 ControlLogix, 1769 Compact for CompactLogix and MicroLogix 1500, and 1771 (PLC-5) Output Modules.

Ready-to-Wire Digital Cables

PanelConnect-ready cables have a cable connector that attaches to the PanelConnect Module, pre-wired to one end, and have free connectors ready to wire to other suppliers’ I/O modules or other components on the other end. PanelConnect ready cables use #22 AWG wire and have individual color-coded conductors for quick wire-to-terminal coordination. The digital PanelConnect-ready cables are offered in standard lengths of 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products.

PanelConnect Fuse Module (optional)

The PanelConnect fuse module provides a convenient method of adding overcurrent protection to your PanelConnect inputs and outputs. This module has sixteen or thirty-two (16 or 32) 5x20 fuse holders to protect each individual input or output. The module has two 20-pin or 40-pin connectors with locking tabs. The right connector is used to connect to the back of the PanelConnect (in-panel connector). The left connector is used to connect to the Input or Output PLC module. The connection between the PanelConnect Module and the Fuse Module is done via the PanelConnect Option Module cable while connection to the PLC is done via PanelConnect pre-wired cables. This module is optional so OEM’s can add fusing based on the needs of their customers.

Click to enlarge - 02060001_A41164-197-02

Digital Option Module Cables

PanelConnect Option Module cable has two over molded cable connectors. The cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection between the fuse module and PanelConnect module every time. These cables are offered in five standard lengths of 0.5, 1.0, 1.5, 2.5, and 5.5 meters to fit a variety of applications.

¬ PanelConnect 16- and 32-point Input...Digital Pre-Wired Cables

T PanelConnect 16- and 32-point Output…Table 1. AC Output Systems NEMA Type 4

‡ Wiring Systems Cable

§ Main Patchcord (Mini-Plus)

§ Distribution Box

Ø Device Patchcords

z Sealing Caps

ª Inductive Proximity...See the Sensors Catalog

v Photoelectric Sensor…See the Sensors Catalog

ª Limit Switch…See the Sensors Catalog

Click to enlarge - UsingSelecTable [Converted]

Product Selection — Input Modules

Using Selection Tables to Make Valid Catalog Numbers

Configure the cable catalog number using 1492-CABLE¬ (for digital cables). See footnote ¬ on pages Table 1. AC Input Systems NEMA Type 4 and .

Table 1. AC Input Systems NEMA Type 4

					Catalog Number
	Allen-Bradley Distribution Box		3-pin mini, no LED		898N-38PS-N10	—	—	—
			3-pin mini, LEDs		—	898N-L38PS-N12	—	—
			3-pin AC micro, no LED		—	—	898R-38PS-N10	—
			3-pin AC micro, LED		—	—	—	898R-L38PS-N12
	Allen-Bradley Device Patchcords				889N-F3AFNU-‡ F		889R-F3AERM-§
	Allen-Bradley Main Patchcords				10-pin Mini Plus	12-pin Mini Plus	10-pin Mini Plus	12-pin Mini Plus
	Allen-Bradley Main Patchcords				889N-F10ACNU-§	889N-F12ACNU-§	889N-F10ACNU-§	889N-F12ACNU-§
	Allen-Bradley PanelConnect (16-input)				1667-16IA1008	1667-16IA1207	1667-16IA1008	1667-16IA1207
System
I/O System	Nominal System	I/O Range	Frequency Module	I/O Module	Cat. No.	Cat. No.	Cat. No.	Cat. No.
1746	100/120V AC	85…132V AC	47…63 Hz	1746-IA16	1492-CABLE¬ A	1492-CABLE¬ A	1492-CABLE¬ A	1492-CABLE¬ A
1746	24V AC	10…30V AC	47…63 Hz	1746-IN16	1492-CABLE¬ B	1492-CABLE¬ B	1492-CABLE¬ B	1492-CABLE¬ B
1756	120V AC	74…132V AC	47…63 Hz	1756-IA16	1492-CABLE¬ X	1492-CABLE¬ X	1492-CABLE¬ X	1492-CABLE¬ X
1756	24V AC	10…30V AC	47…63 Hz	1756-IN16	1492-CABLE¬ X	—	1492-CABLE¬ X	—
1769	100/120V AC	79…132V AC	47…63 Hz	1769-IA16	1492-CAB¬ A69	1492-CAB¬ A69	1492-CAB¬ A69	1492-CAB¬ A69
1771	120V AC	70…138V AC	50/60 Hz	1771-IAD	1492-CABLE¬ F	1492-CABLE¬ F	1492-CABLE¬ F	1492-CABLE¬ F
1771	24V AC	16…30V AC	50/60 Hz	1771-IND	1492-CABLE¬ F	1492-CABLE¬ F	1492-CABLE¬ F	1492-CABLE¬ F
1764	100/120V AC	79…132V AC	47…63 Hz	1764-24AWA	1492-CAB¬ A64	1492-CAB¬ A64	1492-CAB¬ A64	1492-CAB¬ A64
1794	100/120V AC	85…132V AC	47…63 Hz	1794-IA16	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P
Other AC PLC Input Modules					1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P

¬ PanelConnect to PLC I/O module cables are available in standard lengths of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number (“005” = 0.5 m, “010” = 1.0 m, “0.25” = 2.5 m, and “050” = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module. 1492-CABLE¬ P has minimum length of 1.0 m.
‡ Mini patchcords are available in standard lengths of 0.9 m, 1.8 m, 3.6 m, and 6 m (3 ft, 6 ft, 12 ft, and 20 ft). To order, insert the desired length in the catalog number. Example: 889N–F3AFNU–3F represents a mini 0.9 m (3 ft) patchcord. Note catalog number reflects straight male to straight female version with 16 AWG conductors, additional models are also available.
§ AC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889R–F3AERM–3 represents an AC micro 3 m (9.8 ft) patchcord. Note catalog number reflects straight male to straight female version with 18 AWG conductors, additional models are also available.
§ Mini-Plus patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889N–F12ACNU–2 represents a 2 m (6.5 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, additional models are also available.

Table 2. DC Input Systems NEMA Type 4

					Catalog Number
	Allen-Bradley Distribution Box		5-pin DC micro, no LED		898D-58PT-N12
			5-pin DC micro, PNP LED		—	—	898D-P58PT-N12	—	898D-P58PT-N12	—
			5-pin DC micro, NPN LED		—	—	—	898D-N58PT-N12	—	—
			4-pin mini, no LED		898N-48PS-N10		—	—	—	898N-48PS-N10
	Allen-Bradley Device Patchcords				889B-F4AFNU-‡ F		889D-F4ACDM-§			889D-F4AFNU-‡ F
	Allen-Bradley Main Patchcords				10-pin Mini Plus		12-pin Mini Plus			10-pin Mini Plus
	Allen-Bradley Main Patchcords				889N-F10ACNU-§		889N-F12ACNU-§			889N-F10ACNU-§
	PanelConnect (16-input)				1667-16ID1004	1667-16ID1001	1667-16ID1201	1667-16ID1212	—	—
	PanelConnect (32-input)				—	—	—	—	1667-32ID1201	1667-32ID1001
System
I/O System	Nominal System (DC)	I/O Range (DC)‡	Type Module	I/O Module
1746	24V DC	10…30V DC	Sink	1746-IB16	1492-CABLE¬ B	—	1492-CABLE¬ B	—	—	—
	48V DC	30…60V DC	Sink	1746-IC16	1492-CABLE¬ B	—	—	—	—	—
	120V DC	90…146V DC	Sink	1746-IH16	1492-CABLE¬ B	—	—	—	—	—
	24V DC	10…30V DC	Sink	1746-IN16	1492-CABLE¬ B	—	1492-CABLE¬ B	—	—	—
	24V DC	10…30V DC	Sink	1746-ITB16	1492-CABLE¬ B	—	1492-CABLE¬ B	—	—	—
	24V DC	10…30V DC	Source	1746-ITV16	—	1492-CABLE¬ B	—	1492-CABLE¬ BT	—	—
	24V DC	10…30V DC	Source	1746-IV16	—	1492-CABLE¬ B	—	1492-CABLE¬ BT	—	—
	24V DC	30…60V DC	Sink	1746-IB32	—	—	—	—	1492-CABLE¬ H	1492-CABLE¬ H
1756	12/24V DC	10…30V DC	Sink	1756-IB16	1492-CABLE¬ X	—	1492-CABLE¬ X	—	—	—
	48V DC	30…60V DC	Sink	1756-IC16	1492-CABLE¬ X	—	—	—	—	—
	24V DC	10…30V DC	Sink	1756-IB32	—	—	—	—	1492-CABLE¬ Z	1492-CABLE¬ Z
	24V DC	10…30V DC	Source	1756-IV32	—	—	—	—	—	—
1762	24V DC	14…30V DC	Sink	1762-L40BWA	—	—	—	—	1492-CAB¬ A62	1492-CAB¬ A62
1762	24V DC	14…30V DC	Sink	1762-L40BXB	—	—	—	—	1492-CAB¬ A62	1492-CAB¬ A62
1764	24V DC	14…30V DC	Sink	1764-24BWA	1492-CAB¬ A64	1492-CAB¬ A64	1492-CAB¬ A64	—	—	—
1764	24V DC	14…30V DC	Sink	1764-28BXB	1492-CAB¬ B64	1492-CAB¬ B64	1492-CAB¬ B64	—	—	—
1769	24V DC	10…30V DC	Sink	1769-IQ16	1492-CAB¬ B69	—	1492-CAB¬ B69	—	—	—
	24V DC	10…30V DC	Sink	1769-IQ16F	1492-CAB¬ B69	—	1492-CAB¬ B69	—	—	—
	24V DC	10…30V DC	Source	1769-IQ16	—	1492-CAB¬ B69	—	1492-CAB¬ B69	—	—
	24V DC	10…30V DC	Source	1769-IQ16F	—	1492-CAB¬ B69	—	1492-CAB¬ B69	—	—
	24V DC	10…30V DC	Sink	1769-IQ32	—	—	—	—	1492-CAB¬ J69	1492-CAB¬ J69
1771	125V DC	70…138V DC	Sink	1771-IAD	1492-CABLE¬ F	—	—	—	—	—
	24V DC	10…30V DC	Sink	1771-IBD	1492-CABLE¬ F	—	1492-CABLE¬ F	—	—	—
	48V DC	20…60V DC	Sink	1771-ICD	1492-CABLE¬ F	—	1492-CABLE¬ F	—	—	—
	24V DC	9…30V DC	Sink	1771-IND	1492-CABLE¬ F	—	1492-CABLE¬ F	—	—	—
	24V DC	10…30V DC	Sink	1771-IBN	—	—	—	—	1492-CABLE¬ J	1492-CABLE¬ J
1794	24V DC	10…30V DC	Sink	1794-IB16	—	—	1492-CABLE¬ Q	—	—	—
	48V DC	20…60V DC	Sink	1794-IC16	—	—	1492-CABLE¬ Q	—	—	—
	24V DC	10…30V AC	Sink	1794-IB32	—	—	—	—	1492-CABLE¬ Q	1492-CABLE¬ Q
	24V DC	10...30V DC	Source	1794-IV32	—	—	—	—	—	1492-CABLE¬ Q
Other DC PLC Input Modules					1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ Q	1492-CABLE¬ Q

¬ Cables are available in standard lengths of 0.5 m, 1.0 m, and 5.0 m (1.6 ft, 3.2 ft, 16.4 ft). To order, insert the desired length code in the catalog number (“005” = 0.5 m, “010” = 1 m, “0.25” = 2.5 m “050” = 5 m). Example: 1492–CABLE005B is a 0.5m cable. Note 1492–CABLE¬ P has minimum length of 1 m.
‡ Mini patchcords are available in standard lengths of 0.9 m, 1.8 m, 3.6 m, and 6 m (3 ft, 6 ft, 12 ft, and 20 ft). To order, insert the desired length in the catalog number. Example: 889N–F4AFNU–6F represents a mini 1.8 m (6 ft) patchcord. Note catalog number reflects straight male to straight female version with 16 AWG conductors, additional models are also available.
§ DC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889D–F4ACDM–3 represents an DC micro 3 m (9.8 ft) patchcord. Note catalog number reflects straight male to straight female version with 22 AWG conductors, additional models are also available.For use with outputs, 5-pin versions may be required for earth grounding on pin 5 depending on output field device.
§ Mini-Plus patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889N–F12ACNU–2 represents a 2 m (6.5 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, additional models are also available.
Note: PNP type distribution boxes require sink type PLC inputs. NPN type require source inputs.

Table 2. DC Input Systems NEMA Type 4, Continued

			Allen-Bradley Distribution Box LEDs	5-pin DC micro, no LEDs	889D-58PT-M12
			Allen-Bradley Distribution Box LEDs	5-pin DC micro PNP, LEDs	898D-P58PT-M12	—
			Allen-Bradley Device Patchcord		889D-F4ACDM-Ø	889D-F4ACDM-Ø
			Allen-Bradley Main Patchcord		Metric 23 (12-pin)
			Allen-Bradley Main Patchcord		889M-R11RMMU-Ø
			PanelConnect (16-input)		1667-16ID2206	1667-16ID2211
	System
Input System	Nominal	Input Range‡	Type Module	Input Module
1746	24V DC	10…30V DC	Sink	1746-IB16	1492-CABLE¬ B	—
	48V DC	30…60V DC	Sink	1746-IC16	1492-CABLE¬ B	—
	120V DC	90…146V DC	Sink	1746-IH16	—	—
	24V DC	10…30V DC	Sink	1746-IN16	1492-CABLE¬ B	—
	24V DC	10…30V DC	Sink	1746-ITB16	1492-CABLE¬ B	—
	24V DC	10…30V DC	Source	1746-ITV16	—	1492-CABLE¬ B
	24V DC	10…30V DC	Source	1746-IV16	—	1492-CABLE¬ B
	24V DC	10…30V DC	Source	1746-IB32	—	—
	24V DC	10…30V DC	Source	1746-IBN	—	—
1756	12/24V DC	10…30V DC	Sink	1756-IB16	1492-CABLE¬ X	—
	48V DC	30…60V DC	Sink	1756-IC16	1492-CABLE¬ X	—
	24V DC	10…30V DC	Source	1756-IB32	—	—
1764	24V DC	14…30V DC	Sink	1764-24BWA	1492-CAB¬ A64	1492-CAB¬ A64
1764	24V DC	14…30V DC	Sink	1764-28BXB	1492-CAB¬ B64	1492-CAB¬ B64
1769	24V DC	10…30V DC	Sink	1769-IQ16	1492-CAB¬ B69	—
1769	24V DC	10…30V DC	Source	1769-IQ16	—	1492-CAB¬ B69
1771	125V DC	70…138V DC	Sink	1771-IAD	—	—
	24V DC	10…30V DC	Sink	1771-IBD	1492-CABLE¬ F	—
	48V DC	20…60V DC	Sink	1771-ICD	1492-CABLE¬ F	—
	24V DC	9…30V DC	Sink	1771-IND	1492-CABLE¬ F	—
Other DC PLC Intput Modules					1492-CABLE¬ P	1492-CABLE¬ P

¬ Panel Connect to PLC I/O module cables are available in standard lengths of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number (“005” = 0.5 m, “010” = 1.0 m, “0.25” = 2.5 m, and “050” = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module. 1492-CABLE¬ P has minimum length of 1.0 m.
‡ Refer to the PLC module installation manual for details.
§ DC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889D–F4ACDM–3 represents an DC micro 3 m (9.8 ft) patchcord. Note catalog number reflects straight male to straight female version with 22 AWG conductors, additional models are also available.For use with outputs, 5-pin versions may be required for earth grounding on pin 5 depending on output field device.
Ø Replace with length of cable in meters (1 m, 2 m, 3 m, 5 m, or 10 m standard).
Note: PNP type distribution boxes require sink type PLC inputs. NPN type require source inputs.

The same information for PanelConnect NEMA Type 4 applies to PanelConnect NEMA Type 4X products as shown in Tables 1 and 2 for Cables and Distribution Boxes.

Table 3. NEMA Type 4 and 4X Input Systems

NEMA 4X Module	NEMA 4 Module
1667-16IA1008X	1667-16IA1008
1667-16IA1207X	1667-16IA1207
—	—
¬	1667-16ID1001
1667-16ID1004X	1667-16ID1004
1667-16ID1201X	1667-16ID1201
¬	1667-16ID1212
—	—
¬	1667-16ID2206
¬	1667-16ID2211
—	—
¬	1667-32ID1201
¬	1667-32ID1001

¬ Contact factory for availability

PanelConnect™ Specifications

For all PanelConnect dimensions, refer to 16-Point PanelConnect Input or Output Module Dimensions.

For general marker card information, refer to page Marker Cards.

For general adhesive label card information, refer to page Adhesive Label Cards for 16-Point Input PanelConnect Modules.

Refer to the online documentation for new product information.

Click to enlarge - Two-connector-Pinouts

16-Point Input PanelConnect Module with two 10- or 12-pin Mini-Plus Connectors or two 12-pin M23 Connectors

Mini-Plus 12-pin, 1-1/8 in.	Mini-Plus 10-pin, 1-1/8 in.	M23 12-pin, 23 mm
Cat. Nos.	Cat. Nos.	Cat. Nos.
1667-16IA1207	1667-16IA1008	1667-16ID2206
1667-16ID1201	1667-16ID1001	1667-16ID2211
1667-16ID1212	1667-16ID1004

Click to enlarge - 32-pointPanelConnectPLCPwrContRear

Click to enlarge - 32-pointPanelConnectFemaleConnFront

32-Point Input PanelConnect Module with four 10- or 12-pin Mini-Plus Connectors

Mini-Plus 12-pin, 1-1/8 in.		Mini-Plus 10-pin, 1-1/8 in.
Cat. Nos.		Cat. Nos.
1667-32ID1201		1667-32ID1001

Modules for 16-Point Inputs

Features:

Direct connection to common 16-point PLC input modules.

AC and DC versions with color coded ring for voltage indication.

LED power indicator.

Rugged durable construction.

Provides prewired connectivity from on-machine sensor field device to PLC input modules.

Specifications

Cat. No.	1667-161A1008	1667-16ID1001	1667-16ID1004	1667-16IA1207	1667-16ID1201	1667-16ID1212	1667-16ID2206	1667-16ID2211
Field Connector: Number of Pins and Style	10-Pin Mini Plus (1-1/8 in.)			12-Pin Mini Plus (1-1/8 in.)			12-Pin M23 Metric 23 mm
Voltage Rating	10-265V AC	10-265V DC	10-265V DC	10-265V AC	10-265V DC	10-265V DC	10-265V DC	10-265V DC
Module Type	16 Input
Degree of Protection	IP65; Type 1, 4, 4X, 12
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperate Range	0°C…+60°C (32°F…+140°F) Noncondensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE
Power Supply Connector Specification
Wire Range (Rated Cross Section)	#22…#12 AWG (0.2…4 mm²)
Wire Strip Length	8 mm (0.32 in.)
Recommended Tightening Torque	0.50…0.60 N•m (4.5…5.5 lb-in.)

¬ Transient voltage greater than 600Vp use a UL Recognized suprpression device rated at 2.5kV withstand.

Application Notes

1.  Compatiblity- To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.  Wiring- Refer to the label section Pneumatic Valve Wiring Reference Guide.

3.  Dimensions- Refer to 16-Point PanelConnect Input or Output Module Dimensions.

Distribution Block Connection

Match I/O Program to Distribution Block Outputs in the sequence shown below:

Click to enlarge - distributionblockconnection

PanelConnect Pin to Field-Side Connections

Input Connector Pin Reference	Field-Side Connector—10-Pin Mini			Field-Side Connector—12-Pin Mini			Field-Side Connector—M23 12-Pin
	AC	DC	DC	AC	DC	DC	DC	DC
	1667-16IA1008	1667-16ID1001	1667-16ID1004	1667-16IA1207	1667-16ID1201	1667-16ID1212	1667-16ID2206	1667-16ID2211
	1667-16IA1008	1667-16ID1001	1667-16ID1004	1667-16IA1207	1667-16ID1201	1667-16ID1212	1667-16ID2206	1667-16ID2211
1	—	A10,B10	A8,B8	A7,B7	A11,B11	A12,B12	A9,A10, B9. B10	A11, B11
2	—	A10,B10	A8,B8	A7,B7	A11,B11	A12,B12	A9,A10, B9. B10	A11, B11
3	A7	A7	A7	A10	A1	A1	A1	A1
4	A1	A1	A1	A1	A2	A2	A2	A2
5	A9	A9	A9	A12	A3	A3	A3	A3
6	A2	A2	A2	A2	A4	A4	A4	A4
7	A3	A3	A3	A3	A5	A5	A5	A5
8	A4	A4	A4	A4	A6	A6	A6	A6
9	A5	A5	A5	A5	A7	A7	A7	A7
10	A6	A6	A6	A6	A8	A8	A8	A8
11	B7	B7	B7	B10	B1	B1	B1	B1
12	B1	B1	B1	B1	B2	B2	B2	B2
13	B9	B9	B9	B12	B3	B3	B3	B3
14	B2	B2	B2	B2	B4	B4	B4	B4
15	B3	B3	B3	B3	B5	B5	B5	B5
16	B4	B4	B4	B4	B6	B6	B6	B6
17	B5	B5	B5	B5	B7	B7	B7	B7
18	B6	B6	B6	B6	B8	B8	B8	B8
19	A10, B10	A10,B10	A8,B8	A7,B7	A11,B11	A12,B12	A9, A10, B9, B10	A11, B11
20	A10, B10	A10,B10	A8,B8	A7,B7	A11,B11	A12,B12	A9, A10, B9, B10	A11, B11
Power Pin Reference
C	A10, B10	A10, B10	A10, B10	A11, B11	A12, B12	A12, B12	A11, B11	A11, B11
D	—	A8, B8	A8, B8	A7, B7	A11, B11	A11, B11	A9, A10, B9, B10	A9, A10, B9, B10
E	A8, B8	—	—	A9, B9	A9, B9	A9, B9	A12, B12	A12, B12

1.  Compatiblity- To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.  Wiring- Refer to the label section Pneumatic Valve Wiring Reference Guide.

3.  Dimensions- Refer to 16-Point PanelConnect Input or Output Module Dimensions.

Modules for 32-Point Inputs

Features:

Direct connection to common 32-point PLC Input Modules.

LED power indicator.

Rugged durable construction.

Provides prewired connectivity from On-Machine Sensor field device to PLC Input Module.

Specifications

Catalog Number	1667-32ID1001	1667-32ID1201
Field Connector: No. pins Style	10-Pin Mini Plus (1-1/8 in.)	12-Pin Mini Plus (1-1/8 in.)
Voltage Rating	10-30V DC
Module Type	32 Input
Degree of Protection	IP65; Type 1, 4, 4X, 12
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°C…+60°C (32°F…140°F) Noncondensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE
Power Supply Conector Specification
Wire Range (Rated Cross Section)	#22...#12 AWG (0.2...4 mm²)
Wire Strip Length	0.32 in. (8 mm)
Recommended Tightening Torque	4.5...5.5lb.-in. (0.50...0.60 N•m)

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5kV withstand.

Application Notes

Distribution Block Connection

Match I/O Program to Distribution Block Outputs in the sequence shown below:

Click to enlarge - distributionblockconnection2

Panel Connections
Input Connector	Field-Side Connector—10-Pin	Field-Side Connector—12-Pin	Input Connector	Field-Side Connector—10-Pin	Field-Side Connector—12-Pin

	DC	DC		DC	DC
	1667-32ID1001	1667-32ID1201		1667-32ID1001	1667-32ID1201
1	A8, B8, C8, D8	A11, B11, C11, D11	23	B1	B2
2			24	D1	D2
3			25	B9	B3
4			26	D9	D3
5	A7	A1	27	B2	B4
6	C7	C1	28	D2	D4
7	A1	A2	29	B3	B5
8	C1	C2	30	D3	D5
9	A9	A3	31	B4	B6
10	C9	C3	32	D4	D6
11	A2	A4	33	B5	B7
12	C2	C4	34	D5	D7
13	A3	A5	35	B6	B8
14	C3	C5	36	D6	D8
15	A4	A6	37	A8, B8, C8, D8	A11, B11, C11, D11
16	C4	C6	38
17	A5	A7	39
18	C5	C7	40
19	A6	A8	Power Pin Reference
20	C6	C8	C	A10, B10, C10, D10	A12, B12, C12, D12
21	B7	B1	D	A8, B8, C8, D8	A11, B11, C11, D11
22	D7	D1	E	—	A9, B9, C9, D9

Pre-Wired Cables for Input PanelConnect

Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. These pre-wired cables replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and the PanelConnect module.

Specifications

The pre-wired cables have a Bulletin 1746, 1756, 1762 (MicroLogix 1200, 40 I/O Base), 1764 (MicroLogix), 1769, or 1771 PLC input module on one end and a molded cable connector on the other to connect to the PanelConnect Module. The broad offering of digital pre-wired cables supports 16-point and 32-point Bulletin 1746, 1756, 1762, 1764, 1769, and 1771 digital input modules.

Pre-Wired Cable Cat. No.	Standard Cable Lengths	Insulation Rating	No. of Conductors	Conductor Size	Nominal Outer Diameter	I/O Module Connector Cat. No.
1492-CABLE¬ A	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1746-RT25R Red Removable Terminal Block
1492-CABLE¬ B	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1746-RT25B Blue Removable Terminal Block
1492-CABLE¬ F	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1771-WH (16-Point/21 Terminal) Wiring Arm
1492-CABLE¬ X	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1756-TBNH Removable Terminal Block
1492-CAB¬ A69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1769-RTBN18 Removable Terminal Block
1492-CAB¬ B69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1769-RTBN18 Removable Terminal Block
1492-CAB¬ J69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.1 mm (0.46 in.)	(2) 1769-RTBN18 Removable Terminal Blocks
1492-CABLE¬ H	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1746-N3 40-Pin Cable Connector
1492-CABLE¬ J	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1746-WN (32-point/40 Terminal) Wiring Arm
1492-CABLE¬ Z	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1746-TBCH Removable Terminal Block
1492-CABLE¬ X	0.5, 1.0, 2.5, 5.0 m	300V 80°C		#20 AWG	9.0 mm (0.36 in.)	1756-TBNH Removable Terminal Block
1492-CAB¬ A62	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1762-L40xxx Input Terminal
1492-CAB¬ A64	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	9.0 mm (0.36 in.)	1764-24AWA, -24BWA Input Terminal
1492-CAB¬ B64	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	9.0 mm (0.36 in.)	1764-28BXB Input Terminal

¬ Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE005A is for a 0.5 m cable for the 1746-IA16 I/O Module. Also refer to Build-to-Order Length Cables, on [BAD REF 203006 ].

Pinouts

Digital Pre-Wired Cables

The following diagrams illustrate how the individual conductors in the digital pre-wired cables are terminated at both ends. The description listed first is the wire color of the conductor connected to the removable terminal block (Bulletin 1746, 1756, and 1769 I/O) or wiring arm (1771 I/O). The number that follows in parentheses is the corresponding -pin number of the PanelConnect™ mating connect

I/O pin Connector Definition

Click to enlarge - 1492-Cable-Q-Connector-PanelConnect-End

PanelConnect Mating Connector

PanelConnect Digital, Module-Ready Cable Specifications

PanelConnect Module-Ready Cable Specifications

PanelConnect ready cables have a cable connector on one end to attach to the PanelConnect Module plus 20 and 40 individually colored conductors on the other end (Cat. Nos. CABLE¬ P and CABLE¬ Q respectively). These cables allow the PanelConnect Module to be used in specialty applications that require a custom connection, such as connection to other than Allen-Bradley PLCs.

Module-Ready Cable Cat. No.	Cable Lengths	Insulation Rating	Number of Conductors	Conductor Size	Nominal Outer Diameter	Current/ Conductor
1492-CABLE¬ P	1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36")	2 A

Each colored conductor is connected to one pin of the molded cable connector as listed in the tables below.

Connector -pin Number	Wire Color Base/Stripe	Connector pin Number	Wire Color Base/Stripe
1	Black	11	Blue/Black
2	White	12	Black/White
3	Red	13	Red/White
4	Green	14	Green/White
5	Orange	15	Blue/White
6	Blue	16	Black/Red
7	White/Black	17	White/Red
8	Red/Black	18	Orange/Red
9	Green/Black	19	Blue/Red
10	Orange/Black	20	Red/Green

Click to enlarge - Module_Ready_Cable_Page25

Cat. No.	Cable Lengths	Insulation Rating	Number of Conductors	Conductor Size	Nominal Outer Diameter	Current/ Conductor
1492-CABLE¬ Q	1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46")	2 A

Connector -pin Number	Wire Color Base/Stripe	Connector pin Number	Wire Color Base/Stripe
1	Black	21	Orange/Green
2	White	22	Black/White/Red
3	Red	23	White/Black/Red
4	Green	24	Red/Black/White
5	Orange	25	Green/Black/White
6	Blue	26	Orange/Black/White
7	White/Black	27	Blue/Black/White
8	Red/Black	28	Black/Red/Green
9	Green/Black	29	White/Red/Green
10	Orange/Black	30	Red/Black/Green
11	Blue/Black	31	Green/Black/Orange
12	Black/White	32	Orange/Black/Green
13	Red/White	33	Blue/White/Orange
14	Green/White	34	Black/White/Orange
15	Blue/White	35	White/Red/Orange
16	Black/Red	36	Orange/White/Blue
17	White/Red	37	White/Red/Blue
18	Orange/Red	38	Black/White/Green
19	Blue/Red	39	White/Black/Green
20	Red/Green	40	Red/White/Green

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025P is for a 2.5 m, 20 conductor PanelConnect ready cable.

PanelConnect Output Features and Typical Configuration

PanelConnect Output Features

16-Point Output PanelConnect Module with two 12-pin Mini-Plus Connectors

These modules are normally used with Connection systems with LEDs on the distribution box or directly to some pneumatic valve manifolds. Each 12-pin Mini-Plus connector mates with a 12-conductor main patch cord that connects to the distribution box or pneumatic valve manifold. Additionally on the field connection side, various outputs (including pneumatic valves) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the output voltage requirements. Up to 16 outputs can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-output module. Cables are available to connect to the most popular Allen-Bradley PLC output modules. Modules are available in NEMA Type 4 or 4X versions.

16-Point Output PanelConnect Module with two 12-pin M23 Connectors

These modules are used with Connection systems with or without LEDs on the distribution box or directly to some pneumatic valve manifolds. Each 12-pin M23 connector mates with a ten, eleven, or twelve conductor main patch cord that connects to the distribution box or pneumatic valve manifold. Additionally on the field connection side, various outputs (including pneumatic valves) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the output voltage requirements. Up to 16 outputs can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-output module. Cables are available to connect to the most popular Allen-Bradley PLC output modules. Modules are available in NEMA Type 4 or 4X versions.

Click to enlarge - ab_modfront_004945-gray

32-Point Output PanelConnect Module with four 12-pin Mini-Plus Connectors

These modules are used with Connection systems with LEDs on the distribution box or directly to some pneumatic valve manifolds. Each 12-pin Mini-Plus connector mates with a twelve conductor main patch cord that connects to the distribution box. Additionally on the field connection side, various outputs (including pneumatic valves) connect with a variety of connector styles. 24V DC versions of the PanelConnect module are available to meet the output voltage requirements. Up to 32 outputs can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-output module. Cables are available to connect to the most popular Allen-Bradley PLC output modules. Modules are available in NEMA Type 4 or 4X versions.

Digital Pre-Wired Cables

Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Pre-wired cables, when used with a PanelConnect Module replaces the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The pre-wired cables have a removable terminal block or wiring arm at the I/O end of the cable and a cable connector on the other end to connect to the PanelConnect Module. All of the pre-wired cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection every time. The digital pre-wired cables are offered in four standard lengths of 0.5, 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. Pre-wired cables are available for many of the 1746 SLC I/O, 1756 ControlLogix, 1769 Compact for CompactLogix and MicroLogix 1500, and 1771 (PLC-5) Output Modules.

Digital Option Module Cables

PanelConnect Option Module cable has two over molded cable connectors. The cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection betwen the fuse module and PanelConnect module every time. These cables are offered in five standard lengths of 0.5, 1.0, 1.5, 2.5, and 5.5 meters to fit a variety of applications.

Click to enlarge - 02054005hbw_FESTO_wire.txt

Click to enlarge - 02054010_group-festo.txt

Typical Configuration

Product Selection — Output Modules

Using Selection Tables to Make Valid Catalog Numbers

Configure the cable catalog number using 1492-CABLE¬ (for digital cables). See footnote ¬ on pages Table 1. AC Output Systems NEMA Type 4 and .

Table 1. AC Output Systems NEMA Type 4

					Catalog Number
	Distribution Box		3-pin mini, LED		898N-L38PS-N12			—	—	—
	Distribution Box		3-pin AC micro, LED		—	—	—	898R-L38PS-N12
	Device Patchcords				889N-F3AFNU-‡ F			889R-F3AERM-§
	Main Patchcords				12-pin Mini Plus
	Main Patchcords				889N-F12ACNU-§
	PanelConnect (16-output)				1667-16OA1201	1667-16OA1202	1667-16OA1203	1667-16OA1201	1667-16OA1202	1667-16OA1203
System
I/O System	Nominal (AC)	I/O Range (AC)T	Type Module	I/O Module
1746	120/240V AC	85…265V AC	Source	1746-OA16	1492-CABLE¬ C	—	—	1492-CABLE¬ C	—	—
1746	120/240V AC	85…265V AC	Source	1746-OW16	1492-CABLE¬ D	—	—	1492-CABLE¬ D	—	—
1762§ Ø	120/240V AC	5…264V AC	Source	1762-L40AWA	1492-CAB¬ C62	1492-CAB¬ C62	—	1492-CAB¬ C62	1492-CAB¬ C62	—
1762§ Ø	120/240V AC	5…264V AC	Source	1762-L40BWA	1492-CAB¬ C62	1492-CAB¬ C62	—	1492-CAB¬ C62	1492-CAB¬ C62	—
1764‡ Ø	120/240V AC	5…264V AC	Source	1764-24AWA	1492-CAB¬ D64	1492-CAB¬ D64	—	1492-CAB¬ D64	1492-CAB¬ D64	—
1764‡ Ø	120/240V AC	5…264V AC	Source	1764-24BWA	1492-CAB¬ D64	1492-CAB¬ D64	—	1492-CAB¬ D64	1492-CAB¬ D64	—
1769	120/240V AC	85…265V AC	Source	1769-OW16	1492-CAB¬ H69	—	—	1492-CAB¬ H69	—	—
1769	120/240V AC	85…265V AC	Source	1769-OA16	1492-CAB¬ H69	—	—	1492-CAB¬ H69	—	—
1756	120/240V AC	74…265V AC	Source	1756-OA16	—	1492-CABLE¬ X	—	—	1492-CABLE¬ X	—
1771	120V AC	12…138V AC	Source	1771-OAD	—	—	1492-CABLE¬ F	—	—	1492-CABLE¬ F
1771	48V AC	10…60V AC	Source	1771-OND	—	—	1492-CABLE¬ F	—	—	1492-CABLE¬ F
1794	100/120V AC	85…132V AC	Source	1794-OA16	1492-CABLE¬ P	1492-CABLE¬ P	—	1492-CABLE¬ P	1492-CABLE¬ P	—
Other AC PLC Output Modules					1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE005B is for a 0.5 m cable. Note 1492-CABLE¬ P has a minimum length of 1 m.
T Refer to the PLC Installation Manual for details.
‡ Mini patchcords are available in standard lengths of 0.9 m, 1.8 m, 3.6 m, and 6 m (3 ft, 6 ft, 12 ft, and 20 ft). To order, insert the desired length in the catalog number. Example: 889N–F3AFNU–3F represents a mini 0.9 m (3 ft) patchcord. Note catalog number reflects straight male to straight female version with 16 AWG conductors, additional models are also available.
§ AC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889R–F3AERM–3 represents an AC micro 3 m (9.8 ft) patchcord. Note catalog number reflects straight male to straight female version with 18 AWG conductors, additional models are also available.
§ Mini-Plus patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889N–F12ACNU–2 represents a 2 m (6.5 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, additional models are also available.
Ø Refer to Bulletin 1762 and Bulletin 1764 Output Ratings, Table X on 1667-32OD1201 Specifications.

Table 2. DC Output Systems NEMA Type 4

					Catalog Number
	Distribution Box		5-pin DC micro, no LEDs (2 output per connector)		898D-54DT-N12
			5-pin DC micro, no LEDs		898D-58PT-N12
			5-pin DC micro, PNP LEDs		898D-P58PT-N12	—	898D-P58PT-N12			—
			5-pin DC micro, NPN LEDs		—	898D-N58PT-N12	—	—	—	898D-N58PT-N12
	Device Patchcords				889D-F4ACDM-‡
	Main Patchcords				12-pin MIni Plus
	Main Patchcords				889N-F12ACNU-§
	PanelConnect (16-outputs)				1667-16OD1201		1667-16OD1202	1667-16OD1203	—	—
	PanelConnect (32-outputs)				—	—	—	—	1667-32OD1201
System
I/O Systems	Nominal (DC)	I/O Range (DC)T	Type Module	I/O Module
1746	24V DC	10…50V DC	Sourcing	1746-OB16	1492-CABLE¬ E	—	—	—	—	—
	24V DC	10…50V DC	Sourcing	1746-OB16E	1492-CABLE¬ E	—	—	—	—	—
	24V DC	20.4…26.4V DC	Sourcing	1746-OB16P	1492-CABLE¬ E	—	—	—	—	—
	24V DC	10…50V DC	Sinking	1746-OV16	—	1492-CABLE¬ E	—	—	—	—
	24V DC	20.4…26.4V DC	Sinking	1746-OV16P	—	1492-CABLE¬ E	—	—	—	—
	24V DC	5-125V DC	Sourcing	1746-OW16	—	—	—	—	—	—
	24V DC	10…50V DC	Sourcing	1746-OB32	—	—	—	—	1492-CABLE¬ H	—
	24V DC	10…30V DC	Sourcing	1746-OB32E	—	—	—	—	1492-CABLE¬ H	—
	24V DC	10…50V DC	Sinking	1746-OV32	—	—	—	—	—	1492-CABLE¬ H
1756	24V DC	10…31.2V DC	Sourcing	1756-OB16E	—	—	1492-CABLE¬ X	—	—	—
	24V DC	10…31.2V DC	Sourcing	1756-OB32	—	—	—	—	1492-CABLE¬ Z	—
	24V DC	10…31.2V DC	Sinking	1756-OV32E	—	—	—	—	—	1492-CABLE¬ Z
1762§ §	24V DC	5…125V DC	Sourcing	1762-L40AWA	1492-CAB¬ C62	—	—	—	—	—
	24V DC	21.6…27.6V DC	Sourcing	1762-L40BWA	1492-CAB¬ C62	—	—	—	—	—
	24V DC	5…125V DC	Sourcing	1762-L40BXB	1492-CAB¬ D62	—	—	—	—	—
1764‡ §	24V DC	5…125V DC	Sourcing	1764-24AWA	1492-CAB¬ D64	—	—	—	—	—
	24V DC	20.4…26.4V DC	Sourcing	1764-24BWA	1492-CAB¬ D64	—	—	—	—	—
	24V DC	5…125V DC	Sourcing	1764-28BXB	1492-CAB¬ E64	—	—	—	—	—
1769	24V DC	20.4…26.4V DC	Sourcing	1769-OB16	1492-CAB¬ E69	—	—	—	—	—
	24V DC	20.4…26.4V DC	Sinking	1769-OV16	—	1492-CAB¬ E69	—	—	—	—
	24V DC	5-125V DC	Sourcing	1769-OW16	1492-CAB¬ H69	—	—	—	—	—
	24V DC	20.4…26.4V DC	Sourcing	1769-OB32	—	—	—	—	1492-CAB¬ K69	—
1771	24V DC	10…50V DC	Sourcing	1771-OBD	—	—	—	1492-CABLE¬ F	—	—
	24V DC	10…50V DC	Sourcing	1771-OND	—	—	—	—	—	—
	24V DC	10…50V DC	Sourcing	1771-OBN	—	—	—	—	1492-CABLE¬ L	—
	24V DC	10…50V DC	Sinking	1771-OVN	—	—	—	—	—	1492-CABLE¬ L
1794	24V DC	10…50V DC	Sourcing	1794-OB16	1492-CABLE¬ P	—	—	—	—	—
1794	24V DC	10…50V DC	Sourcing	1794-OB32	—	—	—	—	1492-CABLE¬ Q	—
Other 16 Point DC PLC Output Modules					1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P	—	—
Other 32 Point DC PLC Output Modules					—	—	—	—	1492-CABLE¬ Q	—

¬ Cables are available in standard lengths of 0.5 m, 1.0 m, and 5.0 m (1.6 ft, 3.2 ft, 16.4 ft). To order, insert the desired length code in the catalog number (“005” = 0.5 m, “010” = 1 m, “0.25” = 2.5 m “050” = 5 m). Example: 1492–CABLE005B is for a 0.5 m cable. Note 1492–CABLE¬ P as minimum length of 1 m.
T Refer to the PLC Installation Manual for details.
‡ DC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889D–F4ACDM–3 represents an DC micro 3 m (9.8 ft) patchcord. Note catalog number reflects straight male to straight female version with 22 AWG conductors, additional models are also available.For use with outputs, 5-pin versions may be required for earth grounding on pin 5 depending on output field device.
§ Mini-Plus patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889N–F12ACNU–2 represents a 2 m (6.5 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, additional models are also available.
§ Refer to Bulletin 1762 and Bulletin 1764 Output ratings, Table X on 1667-32OD1201 Specifications.
Note: PNP type distribution boxes require source type PLC outputs, NPN require sink outputs.

Table 2. DC Output Systems NEMA Type 4, Continued

					Either with or without LEDs
	Allen-Bradley Distribution Box		5-pin DC micro, no LEDs		898D-58PT-M12
	Allen-Bradley Distribution Box		5-pin DC micro, PNP LEDs		898D-P58PT-M12	—	898D-P58PT-M12
	Allen-Bradley Device Patchcord				889D-F4ACDM-§	—	889D-F4ACDM-§
	Allen-Bradley Main Patchcord 12-pin Metric 23				889M-R11RMMU-§
	PanelConnect (16 output)				1667-16OD2201		1667-16OD2202
System
Output Systems	Nominal	Output RangeT	@ Module	Output Module	—	—	—
1746	24V DC	10…50V DC	Sourcing	1746-OB16	1492-CABLE¬ E	—	—
	24V DC	10…30V DC	Sourcing	1746-OB16E	1492-CABLE¬ E	—	—
	24V DC	20.4…26.4V DC	Sourcing	1746-OB16P	1492-CABLE¬ E	—	—
	24V DC	10…50V DC	Sinking	1746-OV16	—	1492-CABLE¬ E	—
	24V DC	20.4…26.4V DC	Sinking	1746-OV16P	—	1492-CABLE¬ E	—
	24V DC	5-125V DC	Sourcing	1746-OW16	1492-CABLE¬ D	—	—
	24V DC	10…50V DC	Sourcing	1746-OB32	—	—	—
	24V DC	10…30V DC	Sourcing	1746-OB32E	—	—	—
	24V DC	10…50V DC	Sinking	1746-OV32	—	—	—
1756	24V DC	10…31.2V DC	Sourcing	1756-OB16E	—	—	1492-CABLE¬ X
1756	24V DC	10…31.2V DC	Sourcing	1756-OB32	—	—	—
1762§	24V DC	5…125V DC	Sourcing	1762-L40AWA	1492-CAB¬ C62	—	—
	24V DC	21.6…27.6V DC	Sourcing	1762-L40BWA	1492-CAB¬ C62	—	—
	24V DC	5…125V DC	Sourcing	1762-L40BXB	1492-CAB¬ D62	—	—
1764‡	24V DC	5…125V DC	Sourcing	1764-24AWA	1492-CAB¬ D64	—	—
	24V DC	20.4…26.4V DC	Sourcing	1764-24BWA	1492-CAB¬ D64	—	—
	24V DC	5…125V DC	Sourcing	1764-28BXB	1492-CAB¬ E64	—	—
1769	24V DC	20.4…26.4V DC	Sourcing	1769-OB16	1492-CAB¬ E69	—	—
	24V DC	20.4…26.4V DC	Sinking	1769-OV16	—	1492-CAB¬ E69	—
	24V DC	5…125V DC	Sourcing	1769-OW16	1492-CAB¬ H69	—	—
1771	24V DC	10…50V DC	Sourcing	1771-OBD	—	—	—
	24V DC	10…50V DC	Sourcing	1771-OND	—	—	—
	24V DC	10…50V DC	Sourcing	1771-OBN	—	—	—
	24V DC	10…50V DC	Sinking	1771-OVN	—	—	—
1794	24V DC	10…50V DC	Sourcing	1794-OB16	—	—	—
1794	24V DC	10…50V DC	Sourcing	1794-OB32	—	—	—
Other 16-Point DC PLC Output Modules					1492-CABLE¬ P	1492-CABLE¬ P	1492-CABLE¬ P
Other 32-Point DC PLC Output Modules					—	—	—

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end.
T Refer to PLC installation manual for details.
‡ Refer to Bulletin 1764 output ratings, when using PanelConnect, Table X on 1667-32OD1201 (32-Point Output).
§ Refer to Bulletin 1762 output ratings, when using PanelConnect, Table X on 1667-32OD1201 (32-Point Output).
§ Replace with length of cable in meters (1 m, 2 m, 3 m, 5 m, or 10 m standard).
Note: PNP type distribution boxes require source type PLC outputs, NPN require sink outputs.

Table 2. DC Output Systems NEMA Type 4, Continued

					Either with or without LEDs
	Allen-Bradley Distribution Box		5-pin DC micro, no LEDs		898D-58PT-M12
	Allen-Bradley Distribution Box		5-pin DC micro, PNP LEDs		898D-P58PT-M12
	Allen-Bradley Device Patchcord				889M-F4ACDM-§
	Allen-Bradley Main Patchcord 12-pin Metric 23				889M-R11RMMU-§
	PanelConnect (16 output)				1667-16OD2205	1667-16OD2203
System
Output Systems	Nominal	Output RangeT	@ Module	Output Module
1746	24V DC	10…50V DC	Sourcing	1746-OB16	—	—
	24V DC	10…30V DC	Sourcing	1746-OB16E	—	—
	24V DC	20.4…26.4V DC	Sourcing	1746-OB16P	—	—
	24V DC	10…50V DC	Sinking	1746-OV16	—	—
	24V DC	20.4…26.4V DC	Sinking	1746-OV16P	—	—
	24V DC	5-125V DC	Sourcing	1746-OW16	—	—
	24V DC	10…50V DC	Sourcing	1746-OB32	—	—
	24V DC	10…30V DC	Sourcing	1746-OB32E	—	—
	24V DC	10…50V DC	Sinking	1746-OV32	—	—
1756	24V DC	10…31.2V DC	Sourcing	1756-OB16E	1492-CABLE¬ X	—
1756	24V DC	10…31.2V DC	Sourcing	1756-OB32	—	—
1769	24V DC	20.4…26.4V DC	Sourcing	1769-OB16	—	—
	24V DC	20.4…26.4V DC	Sinking	1769-OV16	—	—
	24V DC	5-125V DC	Sourcing	1769-OW16	—	—
1771	24V DC	10…50V DC	Sourcing	1771-OBD	—	1492-CABLE¬ F
	24V DC	10…50V DC	Sourcing	1771-OND	—	1492-CABLE¬ F
	24V DC	10…50V DC	Sourcing	1771-OBN	—	—
	24V DC	10…50V DC	Sinking	1771-OVN	—	—
1794	24V DC	10…50V DC	Sourcing	1794-OB16	—	—
1794	24V DC	10…50V DC	Sourcing	1794-OB32	—	—
Other 16-Point DC PLC Output Modules					1492-CABLE¬ P	1492-CABLE¬ P
Other 32-Point DC PLC Output Modules					—	—

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on [BAD REF 203002 ].
T Refer to PLC installation manual for details.
§ Replace with length of cable in meteres (1 m, 2 m, 3 m, 5 m, or 10 m standard).
Note: PNP type distribution boxes require source type PLC outputs, NPN require sink outputs.

Table X. Bulletin 1764 Output Current Ratings

Output Module Cat. No.	Current per Circuit	Current per Module	Indicator Circuit Current
1764-24AWA (outputs)¬	0.5 A (Out 0…4)	4.0 A	2 mA
1764-24BWA (outputs)¬	0.25 A (Out 4…11)
1764-28BXB (outputs)¬	2.0 A (Out 0…1)
	0.6 A (Out 2…7)
	1.0 A (Out 8…11)

¬ Refer to Bulletin 1764 literature for output voltage ratings. A single power supply must be used with and Bulletin 1667 module.

Table Y. Bulletin 1762 Output Current Ratings

Output Module Cat. No.	Current per Circuit	Current per Module	Indicator Circuit Current
1762-40AWA (outputs)¬	0.25 A	4.0 A	2 mA
1762-40BWA (outputs)¬
1762-40BXB (outputs)¬

¬ Refer to Bulletin 1762 literature for output voltage ratings. A single power supply must be used with and Bulletin 1667 module.

Table 3. AC Output with Direct Connect to Pneumatic Valves

					AC Output
			Main Connector Style		Mini-plus (1-1/8 in.)
			Connectors		12-pin
			Valve Interface		Valve Series	Valve Interface	Valve Interface Cable
			Output points					16	16	16
					Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.	Cat. No.
			Parker Hannifin		“F” Series Air Control ValveT	SCC122NB	—	1667-16OA1201	1667-16OA1202	1667-16OA1203
			Festo		Midi/Maxi Pneumatic Valve Manifold‡	IMP2-03-1§	Build to order from Mfg.	1667-16OA1201	1667-16OA1202	1667-16OA1203
			Festo		Midi/Maxi Pneumatic Valve Manifold‡	IMP2-03-4§	Build to order from Mfg.	1667-16OA1201	1667-16OA1202	1667-16OA1203
	System
I/O System	Nominal	Output Range§	Type Module	I/O Module
1746	120V AC	120…240V AC	Source	1746-OA16	—	—	—	1492-CABLE¬ C	—	—
1756	120V AC	85…265V AC	Source	1756-OA16	—	—	—	—	1492-CABLE¬ X	—
1769	120V AC	74…265V AC	Source	1769-OA16	—	—	—	1492-CAB¬ H69	—	—
1771	120V AC	10…138V AC	Source	1771-OAD	—	—	—	—	—	1492-CABLE¬ F
1794	100/120V AC	85…132V AC	Source	1794-OA16	—	—	—	1492-CABLE¬ P	—	—

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end.
T Voltage Code 23 and 83 valve (120V AC)
‡ 120V AC Solenoid Valves only
§ Maximum 8 outputs
§ Refer to PLC installation manual for details.

Table 4. DC Output with Direct Connect to Pneumatic Valves

Connectors					12-pin
Main Connector Style					Mini-plus (1 1/8in)				Metric 23
Main Patchcord					889N-F12ACNU-§				889M-F11RMMU-§
Output points					16	16	16	32	16	16	16
Valve Interface		Valve Series	Valve Interface Cat. No.	Valve Interface Cable Cat. No.	PanelConnect Catalog Number				PanelConnect Catalog Number
Parker Hanifin		“F” Series Air Control ValveT	SCC122MB	See	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-32OD1201	—	—	—
Festo		Midi/Maxi Pneumatic Valve Manifold‡	IMP2-03-1§	Build to order from manufacturer	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-32OD1201	—	—	—
Festo		Midi/Maxi Pneumatic Valve Manifold‡	IMP2-03-4§	Build to order from manufacturer	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-32OD1201	—	—	—
Festo		“Compact Performance” Valve Manifold	CPV-…VI-MP§	Build to order from manufacturer	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-32OD1201	—	—	—
Festo		“Compact Performance” Valve Manifol	CPA-…-MP§	Build to order from manufacturer	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-32OD1201	—	—	—
Numatics		2005 Valve	AKP…§	Dist.	—	—	—	—	1667-16OD2201	1667-16OD2202	—
Numatics		2012 Valve	AKP…§	Dist.	—	—	—	—	1667-16OD2201	1667-16OD2202	—
Numatics		ISO5599/2 Valve	AKP…§	Dist.	—	—	—	—	1667-16OD2201	1667-16OD2202	—
System					PanelConnect Cable Catalog Number
I/O System	Nominal	I/O Range	@ Module	I/O Module	PanelConnect Cable Catalog Number
1746	24V DC	10…50V DC	Source	1746-OB16	1492-CABLE¬ E	—	—	—	1492-CABLE¬ E	—	—
	24V DC	10…30V DC	Source	1746-OB16E	1492-CABLE¬ E	—	—	—	1492-CABLE¬ E	—	—
	24V DC	20.4…26.4V DC	Source	1746-OBP16	1492-CABLE¬ E	—	—	—	1492-CABLE¬ E	—	—
	24V DC	10…50V DC	Source	1746-OB32	—	—	—	1492-CABLE¬ H	—	—	—
	24V DC	10…30V DC	Source	1746-OB32E	—	—	—	1492-CABLE¬ H	—	—	—
1756	24V DC	10…31.2V DC	Source	1756-OB16E	—	1492-CABLE¬ X	—	—	—	1492-CABLE¬ X	—
1756	24V DC	10…31.2V DC	Source	1756-OB32	—	—	—	1492-CABLE¬ Z	—	—	—
1769	24V DC	20.4…26.4V DC	Source	1769-OB16	1492-CAB¬ E69	—	—	—	1492-CAB¬ E69	—	—
1769	24V DC	20.4…26.4V DC	Source	1769-OB32	—	—	—	1492-CAB¬ K69	—	—	—
1771	24V DC	10…50V DC	Source	1771-OBD	—	—	1492-CABLE¬ F	—	—	—	1492-CABLE¬ F
1771	24V DC	10…50V DC	Source	1771-OBN	—	—	—	1492-CABLE¬ L	—	—	—
1794	24V DC	10…50V DC	Source	1794-OB16	1492-CABLE¬ P	—	—	—	1492-CABLE¬ P	—	—

¬ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. .
T Voltage Code 19 Valve
‡ 24V DC Solenoid Valves Only
§ Maximum of 8 Outputs
§ Mini-Plus patchcords are available in standard legnths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889N-F12ACNU-2 represents a 2 m (6.5 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, addtional models are also available.

The same information for Type 4 applies to Type 4X products as shown in Tables 1…4, 2, and 4…6 for Cables and Distribution Boxes.

Table 5. Type 4X Input and Output Systems

NEMA 4X Module	NEMA 4 Module
1667-16OA1201X	1667-16OA1201
1667-16OA1202X	1667-16OA1202
¬	1667-16OA1203
¬	1667-16OD1201
¬	1667-16OD1202
¬	1667-16OD1203
¬	1667-16OD1204
¬	1667-16OD1205
¬	1667-16OD1206
¬	1667-16OD1207
1667-16OD2201X	1667-16OD2201
1667-16OD2202X	1667-16OD2202
¬	1667-16OD2203
¬	1667-16OD2204
¬	1667-16OD2205
¬	1667-32OD1201

¬ Contact factory for availability. Note: to maintain Type 4X compatibility, refer to Sealing Caps

Table 6. Distribution Boxes

Allen-Bradley Distribution Boxes for Outputs
Typical PanelConnect Modules for PLC Output Platform			Connection Systems - 8 output connections
1746, 1769 and 1794 Catalog Number	1756 Catalog Number	1771 Catalog Number	Distribution Box Catalog Number	Voltage Type	Voltage Range System	LED on Connection Box	Main Connector Type	Output Connection Type	Individual Valve Supported
1667-16OD1201	1667-16OD1202	1667-16OD1203	898D-58PT-N12	DC	10-30V DC	No	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-16OD1201	1667-16OD1202	1667-16OD1203	898D-P58PT-N12 _	DC	10-30V DC	Yes PNP	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-16OD1201	—	—	898D-N58PT-N12 _	DC	10-30V DC	Yes NPN	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-16OA1201	1667-16OA1202	1667-16OA1203	898N-L38PS-N12	AC	85-132V AC	YES	12 pin Mini-Plus (1-1/8 in.)	3-pin Mini	Single
1667-16OA1201	1667-16OA1202	1667-16OA1203	898R-L38PS-N12	AC	85-132V AC	YES	12 pin Mini-Plus (1-1/8 in.)	3-pin Micro	Single
1667-16OD1201	1667-16OD1202	1667-16OD1203	898D-54DT-N12	DC	10-30V DC	NO	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Double
1667-32OD1201	1667-32OD1201	1667-32OD1201	898D-58PT-N12	DC	10-30V DC	No	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-32OD1201	1667-32OD1201	1667-32OD1201	898D-P58PT-N12 _	DC	10-30V DC	Yes PNP	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-32OD1201	—	1667-32OD1201	898D-N58PT-N12 _	DC	10-30V DC	Yes NPN	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Single
1667-32OD1201	1667-32OD1201	1667-32OD1201	898D-54DT-N12	DC	10-30V DC	NO	12 pin Mini-Plus (1-1/8 in.)	5-pin Micro	Double

Note:All References to Crouse Hinds, Daniel Woodhead, Lumberg and Turck were obtained from manufacturers’ commercial literature. Refer to manufacturers’ literature for specific information.

Note: PNP type distribution boxes require source type PLC outputs, NPN require sink outputs.

Click to enlarge - EXPANSION BLOCKpage64

Note: PNP type distribution boxes require source type PLC outputs, NPN require sink outputs.

Table 7. Pneumatic Valve Direct Interfaces

Festo Interface to Panel Connect

PanelConnect Module for Pneumatic Valves	Valve Connection
Catalog Number PanelConnect	Valve Series	Catalog Number To Valve Interface	Catalog Number for Cable from Valve to PanelConnect	Voltage Type & Output Points	Voltage Range	Main Connector Type PanelConnect	Main Connector Type Valve Interface
1667-16OD1201	Midi / Maxi Pneumatic Valve Manifold¬	03E-x-MP4	Build to order by Festo	DC & 16	24V DC	24V DC12-pin Mini-Plus (1-1/8 in.)	25-Pin D-Shell
	“Compact Performance” Valve Manifold	12P-x-MP-xx-x-x
1667-32OD1201	Midi / Maxi Pneumatic Valve Manifold¬	03E-x-MP4	Build to order by Festo	DC & 32
	“Compact Performance” Valve Manifold	12P-x-MP-xx-x-x
1667-16OD1202	Midi / Maxi Pneumatic Valve Manifold¬	03E-x-MP4	Build to order by Festo	DC & 16
	“Compact Performance” Valve Manifold	12P-x-MP-xx-x-x
1667-16OA1203	Midi / Maxi Pneumatic Valve Manifold¬	03E-x-MP4
	“Compact Performance” Valve Manifold	12P-x-MP-xx-x-x
1667-16OA1201	Midi / Maxi Pneumatic Valve ManifoldT	03E-x-MP4	Build to order by Festo	AC & 16	120V AC
1667-16OA1202
1667-16OA1203

Parker Hannifin Interface to Panel Connect

PanelConnect Module for Pneumatic Valves	Valve Connection
Catalog Number PanelConnect	Valve Series	Catalog Number To Valve Interface	Catalog Number for Cable from Valve to PanelConnect	Voltage Type & Output Points	Voltage Range	Main Connector Type PanelConnect	Main Connector Type Valve Interface
1667-16OD1201	“F” Series Air Control Valve‡	SCxxx1MB	889N-F12ACUØ	DC & 16	24V DC	12-pin Mini-Plus (1-1/8 in.)
1667-32OD1201
1667-16OD1202
1667-16OD1203
1667-16OA1201	“F” Series Air Control Valve§	SCxxx1MB		AC & 16	120V AC	12-pin Mini-Plus (1-1/8 in.)
1667-16OA1202
1667-16OA1203

Numatics Interface to Panel Connect

PanelConnect Module for Pneumatic Valves	Valve Connection
Catalog Number PanelConnect	Valve Series	Catalog Number To Valve Interface	Catalog Number for Cable from Valve to PanelConnect§	Voltage Type & Output Points	Voltage Range	Main Connector Type PanelConnect	Main Connector Type Valve Interface
1667-16OD2201	2005 Valve	AKP…	Available from Distributor	DC & 16	24V DC	Metric M23
1667-16OD2201	2012 Valve
1667-16OD2201	ISO 5999/2

Note:Maximum of 8 Outputs per PanelConnect Connector
¬ DC 24V DC Solenoid Valves Only
T AC 120V DC Solenoid Valves Only
‡ Voltage Code 19 Valve
§ Voltage Code 23 and 83 Valve (120V AC)
§ A-B or Numatics distributor that carries on M23 cable.
Ø Mini-Plus patchcords are available in standard legnths of 1 m, 2 m, 3 m, 5 m, and 10 m (0.3 ft, 0.6 ft, 0.9 ft, 1.5 ft and 3 ft). To order, insert the desired length in the catalog number. Example: 889N-F12ACNU-2 represents a 2 m (0.6 ft) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, addtional models are also available.

Digital PanelConnect™ Output Specifications

For all PanelConnect dimensions, refer to 16-Point PanelConnect Input or Output Module Dimensions.

For general marker card information, refer to Marker Cards.

For general adhesive label card information, refer to Adhesive Label Cards for 16-Point Input PanelConnect Modules.

Click to enlarge - Two-Four-connector-Pinouts-Outputs

Output PanelConnect Module with two or four 12-pin Mini-Plus connectors or two 12-pin M23 connectors

16-Point with Mini-Plus 12-pin, 1-1/8 in.	32-Point with Mini-Plus 12-pin, 1-1/8 in.	16-Point with M23 12-pin, 23 mm
Cat. No.	Cat. No.	Cat. No.
1667-16OA1201	1667-32OD1201	1667-16OD2201
1667-16OA1202		1667-16OD2202
1667-16OA1203		1667-16OD2203
1667-16OD1201		1667-16OD2204
1667-16OD1202		1667-16OD2205
1667-16OD1203
1667-16OD1204
1667-16OD1205
1667-16OD1206
1667-16OD1207

Digital PanelConnect™ Modules for Outputs

Features:

Direct connection to common 16- and 32-point PLC output cards.

AC and DC versions with color-coded ring for voltage indication.

LED power indicator.

Rugged durable construction.

Provides pre-wired connectivity from field device to PLC output module.

Cat. No.	1667-16OA1201T	1667-16OA1202T	1667-16OA1203	1667-16OD1201T	1667-16OD1202	1667-16OD1203	1667-16OD1204T	1667-16OD1205	1667-16OD1206	1667-16OD1207
Field Connector Style	12-Pin Mini Plus (1-1/8 in.)
Voltage Rating	10-265V AC			10-265V DC
Module Type	16 Output
Degree of Protection	IP65; Type 1, 4, 4X, 12
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°C…+60°C (32°F…+140°F); Noncondensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE
Power Supply Connector Specification
Wire Range (Rated Cross Section)	#22…#12 AWG (0.2…4 mm²)
Wire Strip Length	8 mm (0.32 in.)
Recommended Tightening Torque	0.50…0.60 N•m (4.5…5.5 lb-in.)

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5kV withstand.
T When using 1667-Oxx PanelConnect modules with bulletin 1762 MicroLogix 1200 embedded or Bulletin 1764 MicroLogix 1500 base I/O, the Bulletin 1667 module current ratings are lower. Refer to Table X, .

Application Notes

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below

1667-160Axxxx

1667-160Dxxxx

Panel Connections
Field Side Connector—12-Pin Mini-Plus

Output Connector Pin Reference	AC	AC	AC	DC	DC	DC	DC	DC	DC	DC
Output Connector Pin Reference	1667-16OA1201	1667-16OA1202	1667-16OA1203	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-16OD1204	1667-16OD1205	1667-16OD1206	1667-16OD1207
	1667-16OA1201	1667-16OA1202	1667-16OA1203	1667-16OD1201	1667-16OD1202	1667-16OD1203	1667-16OD1204	1667-16OD1205	1667-16OD1206	1667-16OD1207
1	A11, B11	A11	A11, B11	A12, B12	A12	A12, B12	A12, B12	A12	A10,B10	A10
2	A11, B11	A7	A11, B11	A12, B12	A11	A12, B12	A12, B12	A10	A10,B10	B11
3	A10	A10	A10	A1	A1	A1	A7	A7	A1	A1
4	A1	A1	A1	A2	A2	A2	A6	A6	A2	A2
5	A12	A12	A12	A3	A3	A3	A5	A5	A3	A3
6	A2	A2	A2	A4	A4	A4	A4	A4	A4	A4
7	A3	A3	A3	A5	A5	A5	A3	A3	A5	A5
8	A4	A4	A4	A6	A6	A6	A2	A2	A6	A6
9	A5	A5	A5	A7	A7	A7	A1	A1	A7	A7
10	A6	A6	A6	A8	A8	A8	A8	A8	A8	A8
11	B10	B10	B10	B1	B1	B1	B7	B7	B1	B1
12	B1	B1	B1	B2	B2	B2	B6	B6	B2	B2
13	B12	B12	B12	B3	B3	B3	B5	B5	B3	B3
14	B2	B2	B2	B4	B4	B4	B4	B4	B4	B4
15	B3	B3	B3	B5	B5	B5	B3	B3	B5	B5
16	B4	B4	B4	B6	B6	B6	B2	B2	B6	B6
17	B5	B5	B5	B7	B7	B7	B1	B1	B7	B7
18	B6	B6	B6	B8	B8	B8	B8	B8	B8	B8
19	A11, B11	B11	A11, B11	A11, B11	B12	A12, B12	A10, B10	B12	A11, B11	A10
20	A11, B11	B7	A7, B7	A11, B11	B11	A11, B11	A10, B10	B10	A11, B11	B11
Power Pin Reference

C				A12, B12	A12, B12	A12, B12	A12, B12	A12, B12	A10, B10	A10, B10
D	A7, A11, B7, B11	A7, A11, B7, B11	A7, A11, B7, B11	A11, B11	A11, B11	A11, B11	A10, B10	A10, B10	A11, B11	A11, B11
E	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9	A9, B9

Click to enlarge - 16-pt_miniplus_12-pin

Modules for 16 Outputs (M23)

Features:

Direct connection to common 16 point output cards.

AC and DC versions with color coded ring for voltage indication.

LED power indicator.

Rugged durable construction.

Provides pre-wired connectivity from field device to PLC output module.

Specifications

Cat. No.	1667-16OD2201T	1667-16OD2202	1667-16OD2203	1667-16OD2204	1667-16OD2205
Number of Pins	12
Field Connector Style	M23 Metric 23mm
Voltage Rating	10...265V DC
Number of Points	16
Degree of Protection	IP65 Type 1, 4, 4X, 12
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Column	2
Operating Temperature Range	0°...+60°C (32°…140°F) Non-Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE
Power Supply Connector Specifications
Wire Range (Rated Cross Section)	#22...#12 AWG (0.2...4 mm²)
Wire Strip Length	0.32 in. (8 mm)
Recommended Tightening Torque	4.5...5.5 lb.-in. (0.50...0.60 N•m)

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5kV withstand.
T When using 1667-Oxx PanelConnect modules with bulletin 1762 MicroLogix 1200 embedded or Bulletin 1764 MicroLogix 1500 base I/O, the Bulletin 1667 module current ratings are lower. Refer toTable X, .

Application Notes

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Panel Connections
Field Side Connector—12-Pin M23

Output Connector Pin Reference	DC	DC	DC	DC	DC
Output Connector Pin Reference	1667-16OD2201	1667-16OD2202	1667-16OD2203	1667-16OD2204	1667-16OD2205
	1667-16OD2201	1667-16OD2202	1667-16OD2203	1667-16OD2204	1667-16OD2205
1	A11, B11	A11	A11, B11	A1, B1	A1, B1
2	A11, B11	A9, A10	A11, B11	A1, B1	A3, B3
3	A1	A1	A1	A4	A4
4	A2	A2	A2	A5	A5
5	A3	A3	A3	A6	A6
6	A4	A4	A4	A7	A7
7	A5	A5	A5	A8	A8
8	A6	A6	A6	A9	A9
9	A7	A7	A7	A10	A10
10	A8	A8	A8	A11	A11
11	B1	B1	B1	B4	B4
12	B2	B2	B2	B5	B5
13	B3	B3	B3	B6	B6
14	B4	B4	B4	B7	B7
15	B5	B5	B5	B8	B8
16	B6	B6	B6	B9	B9
17	B7	B7	B7	B10	B10
18	B8	B8	B8	B11	B11
19	A9, A10	B11	A11, B11	A3, B3	A1, B1
20	B9, B10	B9, B10	A9,A10, B9, B10	A3, B3	A3, B3
Power Pin Reference
C	A11, B11	A11, B11	A11, B11	A1, B1	A1, B1
D	A9, A10, B9, B10	A9, A10, B9, B10	A9, A10, B9, B10	A3, B3	A3, B3
E	A12, B12	A12, B12	A12, B12	A12, B12	A12, B12

1667-32OD1201 (32-Point Output)

1667-32OD1201 Specifications

Main PanelConnect Connector	Number of pins	12
	Style	Mini-Plus 1-1/8 in.
	Number of points	32

Degree of Protection	IP65 Type 1, 4, 4X, 12
Voltage Rating	10…30V DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0…+60×C Non-Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

	Power Supply Connector Specification
Wire Range (Rated Cross Section)		#22…#12 AWG (0.2…4 mm²)
Wire Strip Length		0.32 in. (8 mm)
Recommended Tightening Torque		4.5…5.5 lb.-in. (0.50…0.60 Nm)

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Pinout

Click to enlarge - Front_12-pin-32-point-Mini-plus-with-callouts

Panel Connections
Connector Pin Reference	Field Side Connector	Connector Pin Reference	Field Side Connector

1	A12, B12, C12, D12	21	B1
2		22	D1
3		23	B2
4		24	D2
5	A1	25	B3
6	C1	26	D3
7	A2	27	B4
8	C2	28	D4
9	A3	29	B5
10	C3	30	D5
11	A4	31	B6
12	C4	32	D6
13	A5	33	B7
14	C5	34	D7
15	A6	35	B8
16	C6	36	D8
17	A7	37	A11, B11, C11, D11
18	C7	38
19	A8	39
20	C8	40
Power Pin Reference

		C	A12, B12
		D	A11, B11, C11, D11
		E	A9, B9, C9, D9

Application Notes

1.   Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.   Wiring — Refer to the label section on [BAD REF 202766 ].

3.   Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

Note:For configuring to double solenoid valves, refer to Table 6. Distribution Boxes for Distribution Box connections.

Table X. PLC-Specific Current Ratings

Cat. No.	Current/Circuit	Current/Module	Indicator Circuit Current	Operating Temperature Range
1762-40AWA (Outputs) ¬	0.25 A	4.0 A	2 mA	0°…60°C
1762-40BWA (Outputs) ¬
1762-40BXB (Outputs) ¬
1764-24AWA (Outputs) ¬	0.5 A (Outputs 0…4) 0.25 A (Outputs 4…11)
1764-24BWA (Outputs) ¬
1764-28BXB (Outputs) ¬	2.0 A (Outputs 0…1) 0.6 A (Outputs 2…7) 1.0 A (Outputs 8…11)

¬ Refer to Bulletin 1762 and 1764 literature for output voltage ratings.

Pre-Wired Cables for Output PanelConnect™

Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Digital pre-wired cables, when used with a PanelConnect™ Module, replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The digital ready-to-wire cables provide one end of the cable pre-terminated, for the PanelConnect Module.

Specifications

The pre-wired cables have a Bulletin 1746 Removable Terminal Block, 1756 Removable Terminal Block, 1769 Removable Terminal Block, or 1771 Wiring Arm on one end and a cable connector on the other to connect to the PanelConnect Module. The broad offering of digital pre-wired cables supports Bulletin 1746, 1756, 1769, and 1771 digital modules.

Cat. No.	Standard Cable Lengths	Insulation Rating	No. of Conductors	Conductor Size	Nominal Outer Diameter	I/O Module Connector Cat. No.
1492-CABLE¬ C	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1746-RT25R Red Removable Terminal Block
1492-CABLE¬ D	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1746-RT25C Orange Removable Terminal Block
1492-CABLE¬ E	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1746-RT25B Blue Removable Terminal Block
1492-CABLE¬ F	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1771-WH (16-Point/21 Terminal) Wiring Arm
1492-CABLE¬ H	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1746-N3 40-pin cable connector
1492-CABLE¬ L	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1771-WN (32-point/40 Terminal) Wiring Arm
1492-CABLE¬ X	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1756-TBNH Removable Terminal Block
1492-CABLE¬ Z	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1756-TBCH Removable Terminal Block
1492-CAB¬ B62	0.5, 1.0, 2.5, 5.0 m	300V 80°C	40	#22 AWG	11.7 mm (0.46 in.)	1762-L40xxx Output Terminal
1492-CAB¬ C64	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1764-24AWA, -24BWA Output Terminal
1492-CAB¬ F64	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1764-28BXB Output Terminal
1492-CAB¬ E69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	1769-RTBN18 Removable Terminal Block
1492-CAB¬ H69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	11.0 mm (0.46 in.)	1769-RTBN18 Removable Terminal Block
1492-CAB¬ K69	0.5, 1.0, 2.5, 5.0 m	300V 80°C	20	#22 AWG	9.0 mm (0.36 in.)	(2) 1769-RTBN18 Removable Terminal Block

¬ Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE005A is for a 0.5 m cable for the 1746-IA16 I/O Module.

I/O pin Connector Definition

Click to enlarge - PanelConnect Mating Connector

PanelConnect Mating Connector

Combination PanelConnect Features

32-Point Combination Input/Output PanelConnect Module with four 12-pin Mini-Plus Connectors

These modules are used when input and output devices are in the vicinity of each other (i.e., conveyor systems).

Each 12-pin Mini-Plus connector connects to four (4) input and four (4) output devices. The distribution box used in this application is split between four (4) inputs and four (4) outputs. Each 12-pin Mini-Plus connector mates with a twelve-conductor patchcord that connects to the distribution box.

These modules are normally used with Connection systems with LEDs on the distribution box, for easier identification on the machine. The 32-Point combination modules are available only for DC inputs and outputs.

Each PanelConnect module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with two 20-pin cables, one for PLC input modules and one for PLC output modules. These cables are available for the most popular Allen-Bradley Input and Output I/O modules. Modules are available in Type 4 and 4X versions.

¬ PanelConnect Combination
32-point Input/Output...Digital Pre-Wired Cables

T Wiring Systems Cable

‡ Main Patchcord (Mini-Plus)

§ Distribution Box

§ Device Patchcords

Ø Sealing Caps…Sealing Caps

z Inductive Proximity...See the Sensors Catalog

ª Photoelectric Sensor…See the Sensors Catalog

v Limit Switch…See the Sensors Catalog

Click to enlarge - ab_modfront_004945-gray_txt

Click to enlarge - ab_locable cu_006951.pg78_txt

Click to enlarge - ab_encl_006949_pg78_txt

Typical Configuration

Click to enlarge - panel_drawing_comb_pg77

Selecting Combination Products

Follow these steps when starting selection from the I/O Module and PanelConnect:

1.  Determine the Input or Output voltage type. Use Table 1 for DC Outputs systems with Distribution Box connection.

2.  Determine the PLC I/O system that you are using, 1746, 1756, 1769, 1771, 1762, 1764, 1794

3.  The main connector for all combination modules is a Mini-Plus - 1 1/8 in. type.

4.  All available Distribution Box have LED indicators

5.  Select the appropriate PanelConnect module and a cable

6.  If Type 4X system is required, select from Table 2

Note:Appropriate Connection Systems suppliers are noted in Tables 1…3. Appropriate Pneumatic Valve suppliers are noted in Table 1.

Refer to Table 3 for each supplier for Distribution Box details.

Follow these steps when starting selection from Output Distribution Box and connect type:

Determine Output Distribution Box details, first

1.  Determine manufacturer of Distribution Box

2.  Determine voltage type DC, and nominal voltage

3.  Determine Distribution Box with LED

4.  Determine connection type

5.  Select PanelConnect Module and a cable

Refer to Table 1 to determine appropriate output system and PanelConnect Cable.

Follow these steps when starting selection from direct connect Pneumatic valves Manifold:

Determine Pneumatic Valve Manifold details, first

1.  Determine manufacturer of pneumatic valve

2.  Determine voltage type AC or DC

3.  Determine Pneumatic Valve series

4.  Select Valve Interface (Table 2 or 3)

5.  Select PanelConnect Module and a cable

Refer to Table 1 to determine appropriate output system and PanelConnect cable

Table 1. 32-Point Combination Modules

DC Combination Input and Output

Distribution Box

5-pin DC micro, no LEDs, dual input/output per port

898D-54DT-N12

—

898D-54DT-N12

5-pin DC micro, no LEDs

898D-58PT-N12

—

898D-58PT-N12

5-pin DC micro, PNP LEDs

898D-P58PT-N12

—

5-pin DC micro, NPN LEDs

—

898D-N58PT-N12

Device Patchcords

889D-F4ACDM-§

Main Patchcord
Mini-plus ( 1-1/8 in.) 12-pin

889N-F12ACNU-§

PanelConnect

1667-32CD1201

1667-32CD1202

1667-32CD1203

1667-32CD1204

Allen-Bradley Input Systems

Allen-Bradley Output Systems

I/O System

Nominal

Input Range

Type Module

Input Module

Input CableT

Output Cable‡

Input CableT

Output Cable‡

Input CableT

Output Cable‡

Input CableT

Output Cable‡

Nominal

Input Range

Type Module

Output Module

1746

24V DC

10…30V

Sink

1746-IB16

1492-CABLE¬ B

1492-CABLE¬ E

—

24V DC

10…30V

Source

1746-OB16E

24V DC

10…30V AC/DC

Sink

1746-IN16

1492-CABLE¬ B

1492-CABLE¬ E

—

24V DC

10…30V

Source

1746-OB16E

24V DC

10…30V DC

Sink

1746-ITB16

1492-CABLE¬ B

1492-CABLE¬ E

—

24V DC

10…30V

Source

1746-OB16E

24V DC

10…30V DC

Source

1746-ITV16

—

1492-CABLE¬ E

24V DC

10…50V DC

Sink

1746-OV16

24V DC

10…30V DC

Source

1746-IV16

—

1492-CABLE¬ B

1492-CABLE¬ E

24V DC

20…26V DC

Sink

1746-OVP16

1756

24V DC

10…30V DC

Sink

1756-IB16

—

1492-CABLE¬ X

—

24V DC

10…30V DC

Source

1756-OB16E

1769

24V DC

10…30V DC

Sink Only

1769-IQ16 (Sink Mode)

1492-CAB¬ B69

1492-CAB¬ E69

—

24V DC

20…26V DC

Source

1769-OB16

24V DC

10…30V DC

Source

1769-IQ16 (Source Mode)

—

1492-CAB¬ B69

1492-CAB¬ E69

24V DC

20…26V DC

Sink

1769-OV16

1771

24V DC

10…30V DC

Sink
Only

1771-IBD

—

1492-CABLE¬ F

—

24V DC

10…50V DC

Source

1771-OBD

24V DC

20…60V DC

Sink

1771-ICD

—

1492-CABLE¬ F

—

24V DC

10…50V DC

Source

1771-OBD

24V DC

9…30V DC

Sink

1771-IND

—

1492-CABLE¬ F

—

24V DC

10…50V DC

Source

1771-OBD

1794

24V DC

10…30V DC

Sink

1794-IB16

1492-CABLE¬ P

—

1492-CABLE¬ P

24V DC

10…30V DC

Source

1794-OB16

¬ Cables are available in standard lengths of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number (“005” = 0.5 m, “010” = 1.0 m, “0.25” = 2.5 m, and “050” = 5 m). Example:
1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module. 1492-CABLE¬ P has minimum length of 1.0 m.

T The input cable mates to the Allen-Bradley input system input module.

‡ The output cable mates to the Allen-Bradley input system output module.

§ Mini patchcords are available in standard lengths of 0.9 m, 1.8 m, 3.6 m, and 6 m (3 ft., 6 ft., 12 ft., and 20 ft.). To order, insert the desired length in the catalog number. Example: 889N-F12ACNU-2 represents a 2 m (6.5 ft.) patchcord. Note catalog number reflects straigh male to straight female version with 18/22 AWG conductors, additional models are also available.

§ DC micro patchcords are available in standard lengths of 1 m, 2 m, 3 m, 5 m, and 10 m (3.3 ft, 6.5 ft, 9.8 ft, 16.4 ft and 32.8 ft). To order, insert the desired length in the catalog number. Example: 889D-F4ACDM-2 represents a 2 m (6.5 ft.) patchcord. Note catalog number reflects straight male to straight female version with 18/22 AWG conductors, additional models are also available.

Note:PNP type disitrubtion boxes require sink type PLC inputs and source type PLC outputs. NPN type distribution boxes require source type PLC inputs and sink type PLC outputs.

Digital PanelConnect™ Combination Specifications

For all PanelConnect dimensions, refer to 16-Point PanelConnect Input or Output Module Dimensions.

For general marker card information, refer to Marker Cards.

For general adhesive label card information, refer to Adhesive Label Cards for 16-Point Input PanelConnect Modules.

Refer to the online documentation for new product information.

1667-32CD1201

Click to enlarge - 03019004_1667-32OD1201-Gray

1667-32CD1201 Specifications

Main PanelConnect Connector	No. pins	12
Main PanelConnect Connector	Style	Mini-Plus 1-1/8 in.
	Type	16 Input / 16 Output
	No Points	32-Point Combination

Degree of Protection	IP65 Type 1, 4, 4X, 12
Voltage Rating	10…30V DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°…+60°C (32°…140°F) Non Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

	Power Supply Connector Specification
Wire Range (Rated Cross Section)		#22…#12 AWG (0.2…4 mm²)
Wire Strip Length		0.32 in. (8 mm)
Recommended Tightening Torque		4.5…5.5 lb.-in. (0.50…0.60 N•m)

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Pinout

Connector Pin Reference Input	Field Side Connector	Connector Pin Reference Output	Field Side Connector

1	—	1	C12, D12
2	—	2	C12, D12
3	A1	3	A5
4	A2	4	A6
5	A3	5	A7
6	A4	6	A8
7	B1	7	B5
8	B2	8	B6
9	B3	9	B7
10	B4	10	B8
11	C1	11	C5
12	C2	12	C6
13	C3	13	C7
14	C4	14	C8
15	D1	15	D5
16	D2	16	D6
17	D3	17	D7
18	D4	18	D8
19	A11, B11	19	C11, D11
20	A11, B11	20	C11, D11
		Power Pin Ref.
		C	A12, B12, C12, D12
		D	A11, B11, C11, D11
		E	A9, B9, C9, D9

Application Notes

1.   Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.   Wiring — Refer to the label section on [BAD REF 214245 ].

3.   Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

1667-32CD1202

1667-32CD1202 Specifications

Main PanelConnect Connector	No. pins	12
Main PanelConnect Connector	Style	Mini-Plus 1-1/8 in.
	Type	16 Input / 16 Output
	No Points	32-Point Combination

Degree of Protection	IP65 Type 1, 4, 4X, 12
Voltage Rating	10…30V DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°…+60°C (32°…140°F) Non Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

	Power Supply Connector Specification
Wire Range (Rated Cross Section)		#22…#12 AWG (0.2…4 mm²)
Wire Strip Length		0.32 in. (8 mm)
Recommended Tightening Torque		4.5…5.5 lb.-in. (0.50…0.60 N•m)

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Pinout

Connector Pin Reference Input	Field Side Connector	Connector Pin Reference Output	Field Side Connector

1	A11, B11	1	C12, D12
2	A11, B11	2	C11, D11
3	A1	3	A5
4	A2	4	A6
5	A3	5	A7
6	A4	6	A8
7	B1	7	B5
8	B2	8	B6
9	B3	9	B7
10	B4	10	B8
11	C1	11	C5
12	C2	12	C6
13	C3	13	C7
14	C4	14	C8
15	D1	15	D5
16	D2	16	D6
17	D3	17	D7
18	D4	18	D8
19	A11, B11	19	C12, D12
20	A11, B11	20	C11, D11
		Power Pin Ref.
		C	A12, B12, C12, D12
		D	A11, B11, C11, D11
		E	A9, B9, C9, D9

Application Notes

1.   Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.   Wiring — Refer to the label section on Adhesive Label Cards for 16-Point Output PanelConnect Modules.

3.   Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

1667-32CD1203

1667-32CD1203 Specifications

Main PanelConnect Connector	No. pins	12
Main PanelConnect Connector	Style	Mini-Plus 1-1/8 in.
	Type	16 Input / 16 Output
	No Points	32-Point Combination

Degree of Protection	IP65 Type 1, 4, 4X, 12
Voltage Rating	10…30V DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°…+60°C (32°…140°F) Non Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

	Power Supply Connector Specification
Wire Range (Rated Cross Section)		#22…#12 AWG (0.2…4 mm²)
Wire Strip Length		0.32 in. (8 mm)
Recommended Tightening Torque		4.5…5.5 lb.-in. (0.50…0.60 N•m)

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Pinout

Connector Pin Reference Input	Field Side Connector	Connector Pin Reference Output	Field Side Connector

1	—	1	C12, D12
2	—	2	C12, D12
3	A1	3	A5
4	A2	4	A6
5	A3	5	A7
6	A4	6	A8
7	B1	7	B5
8	B2	8	B6
9	B3	9	B7
10	B4	10	B8
11	C1	11	C5
12	C2	12	C6
13	C3	13	C7
14	C4	14	C8
15	D1	15	D5
16	D2	16	D6
17	D3	17	D7
18	D4	18	D8
19	—	19	C12, D12
20	A11, B11	20	C11, D11
		Power Pin Ref.
		C	A12, B12, C12, D12
		D	A11, B11, C11, D11
		E	A9, B9, C9, D9

Application Notes

1.   Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.   Wiring — Refer to the label section on Adhesive Label Cards for 16-Point Output PanelConnect Modules.

3.   Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

1667-32CD1204

1667-32CD1204 Specifications

Main PanelConnect Connector	No. pins	12
Main PanelConnect Connector	Style	Mini-Plus 1-1/8 in.
	Type	16 Input / 16 Output
	No Points	32-Point Combination

Degree of Protection	IP65 Type 1, 4, 4X, 12
Voltage Rating	10…30V DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Indicator Circuit Current (Nominal)	2 mA
No. of Terminals per Device Common	2
Operating Temperature Range	0°…+60°C (32°…140°F) Non Condensing
Certifications	cULus Listed (File E113724 Guide NRAQ) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

	Power Supply Connector Specification
Wire Range (Rated Cross Section)		#22…#12 AWG (0.2…4 mm²)
Wire Strip Length		0.32 in. (8 mm)
Recommended Tightening Torque		4.5…5.5 lb.-in. (0.50…0.60 N•m)

Distribution Block Connection

Match I/O Program to Distribution Block outputs in the sequence shown below:

Pinout

Connector Pin Reference Input	Field Side Connector	Connector Pin Reference Output	Field Side Connector

1	A12, B12	1	C12, D12
2	A12, B12	2	C12, D12
3	A1	3	A5
4	A2	4	A6
5	A3	5	A7
6	A4	6	A8
7	B1	7	B5
8	B2	8	B6
9	B3	9	B7
10	B4	10	B8
11	C1	11	C5
12	C2	12	C6
13	C3	13	C7
14	C4	14	C8
15	D1	15	D5
16	D2	16	D6
17	D3	17	D7
18	D4	18	D8
19	A12, B12	19	C11, D11
20	A12, B12	20	C11, D11
		Power Pin Ref.
		C	A12, B12, C12, D12
		D	A11, B11, C11, D11
		E	A9, B9, C9, D9

Application Notes

1.   Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module.

2.   Wiring — Refer to the label section on Adhesive Label Cards for 16-Point Output PanelConnect Modules.

3.   Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

Accessories

PanelConnect Fuse Module

The PanelConnect fuse module provides a convenient method of adding overcurrent protection to your PanelConnect inputs and outputs. This module has sixteen or thirty-two (16 or 32) 5x20 fuse holders to protect each individual input or output. The module has two 20-pin or 40-pin connectors with locking tabs. The right connector is used to connect to the back of the PanelConnect (in-panel connector). The left connector is used to connect to the Input or Output PLC module. The connection between the PanelConnect Module and the Fuse Module is done via the PanelConnect Option Module cable while connection to the PLC is done via PanelConnect pre-wired cables. This module is optional so OEM’s can add fusing based on the needs of their customers.

Digital Option Module Cables

PanelConnect Option Module cable has two over molded cable connectors. The cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection between the fuse module and PanelConnect Module every time. These cables are offered in five standard lengths of 0.5, 1.0, 1.5, 2.5, and 5.5 meters to fit a variety of applications.

Click to enlarge - Sealing Caps Installed

Sealing Caps

To maintain the Type 4, 4X, and 12 enclosure rating, these accessory caps must be used if both field side connectors are not permanently terminated. Hand tighten plus one quarter turn.

PanelConnect Catalog Number	1667-ZC1¬ Mini-Plus 1-1/8 in.	1667-ZC2¬ M23	PanelConnect Catalog Number	1667-ZC1¬ Mini-Plus 1-1/8 in.	1667-ZC2¬ M23
1667-16IA1008	X		1667-16OD1202	X
1667-16IA1207	X		1667-16OD1203	X
1667-16IA2209		X	1667-16OD1204	X
1667-16ID1001	X		1667-16OD1205	X
1667-16ID1004	X		1667-16OD1206	X
1667-16ID1201	X		1667-16OD1207	X
1667-16ID1202	X		1667-16OD2201		X
1667-16ID1203	X		1667-16OD2202		X
1667-16ID1210	X		1667-16OD2203		X
1667-16ID1212	X		1667-16OD2204		X
1667-16ID2205		X	1667-16OD2205		X
1667-16ID2206		X	1667-32CO1201	X
1667-16ID2211		X	1667-32CO1202	X
1667-16ID2213		X	1667-32CO1203	X
1667-16OA1201	X		1667-32CO1204	X
1667-16OA1202	X		1667-32ID1201	X
1667-16OA1203	X		1667-32ID1202	X
1667-16OD1201	X		1667-32OA1201	X

¬ Add X to Cat. No. for NEMA 4X sealing cap

Mounting Bracket

Use the above bracket (1667-ZB) when mounting the PanelConnect module within an enclosure.

Marker Cards

Each PanelConnect is provided with markers ¬ , T installed in the front of the module. The center marker T indicates whether the module is an input or output combined device. The blank markers ¬ are for customer use to mark I/O address or cable reference. In addition, each PanelConnect is provided with a tree of five markers for machine marking. Replacement and spare markers are available as accessories, 1492-M9X20.

Voltage Marking Ring

Each PanelConnect™ module is provided with two voltage marking rings(‡ ). AC modules use the red rings provided and DC modules use the blue rings.

Click to enlarge - voltagemarkingring2page99

The same information for Type 4 applies to Type 4X products as shown in Tables 1 and 2 for Cables and Distribution Boxes.

Table 2. Type 4X Input Systems

Type 4X Module	Type 4 Module
¬	1667-32CD1201
¬	1667-32CD1202
¬	1667-32CD1203
¬	1667-32CD1204

¬ Contact factory for availability

Adhesive Label Cards for 16-Point Input PanelConnect Modules

Each PanelConnect™ module is provided with an adhesive label card. The label card is made available for the back of the PanelConnect Module and provides the power supply connector descriptions. The label strips provides the wiring description from the input module power connections.

The label lists (‡ ) all of the compatible input modules and their respective power wiring descriptions. Depending on the input module that is used, the label strip is simply peeled from the label card and applied to the back side power supply connector (‡ ).

In addition, blank labels are provided for:

marking the pre-wired cable with identification label (§ )

marking the PanelConnect Module identification the inside of the panel label(§ Ø )

1667-16IA1008	1667-16ID1001	1667-16ID2205
1667-16IA1207	1667-16ID1004	1667-16ID2206
1667-16IA2209	1667-16ID1201	1667-16ID2211
	1667-16ID1202	1667-16ID2213
	1667-16ID1203
	1667-16ID1212

Click to enlarge - Input_Dimensions_marker

16-Point Input Label Card with Labels

Adhesive Label Cards for 16-Point Output PanelConnect Modules

Each PanelConnect™ module is provided with an adhesive label card. The label card is made available for the back of the PanelConnect Module and provides the power supply connector descriptions. The label strips provides the wiring description from the input module power connections.

The label lists (‡ )all of the compatible input modules and their respective power wiring descriptions. Depending on the input module that is used, the label strip is simply peeled from the label card and applied to the back side power supply connector (‡ ).

In addition, blank labels are provided for:

marking the pre-wired cable with identification label (§ )

marking the PanelConnect Module identification the inside of the panel label (§ Ø )

1667-16OA1201	1667-16OD1201	1667-16OD2201	1667-16OD2204
1667-16OA1202	1667-16OD1202	1667-16OD2202	1667-16OD2205
1667-16OA1203	1667-16OD1203	1667-16OD2203
	1667-16OD1204
	1667-16OD1205
	1667-16OD1206
	1667-16OD1207

16-Point Output Label Card with Labels

Adhesive Label Cards for 32-Point Input, Output and Combination Input/Output PanelConnect Modules

Each PanelConnect™ module is provided with an adhesive label card. The label card is made available for the back of the PanelConnect Module and provides the power supply connector descriptions. The label strips provides the wiring description from the input module power connections.

The label lists (‡ ) all of the compatible input modules and their respective power wiring descriptions. Depending on the input module that is used, the label strip is simply peeled from the label card and applied to the back side power supply connector (‡ ).

In addition, blank labels are provided for:

marking the pre-wired cable with identification label

marking the PanelConnect Module identification the inside of the panel label (§ Ø )

Combination	Input	Output
1667-32CD1201	1667-32ID1001 1667-32ID12001	1667-32OD1201
1667-32CD1202
1667-32CD1203
1667-32CD1204

Fuse Modules

1667-Z16F

1667-Z16F Specifications

Option Module Connector	No. pins	20
	Style	Male

Degree of Protection	IP20
Voltage Rating	10…265V AC/DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Operating Temperature Range	0°…+60°C (32°…140°F) Non-Condensing
Certifications	cURus Recognized (File E113724 Guide NRAQ2) CSA Certified (File LR1234) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

Pinout

Fuse Module Connections
Connector Pin Reference from I/O	PLC Connector	Connector Pin Reference from I/O	PLC Connector

1	1	11	11
2	2	12	12
3	3	13	13
4	4	14	14
5	5	15	15
6	6	16	16
7	7	17	17
8	8	18	18
9	9	19	19
10	10	20	20

Application Notes

1. Compatibility — To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the fuse and PanelConnect Module.

2. Dimensions — Refer to 16-Point PanelConnect Input or Output Module Dimensions.

1667-Z32F

Click to enlarge - ab_fusemod_006806-Grayscale

1667-Z32F Specifications

Option Module Connector	No. pins	40
	Style	Male

Degree of Protection	IP20
Voltage Rating	10…265V AC/DC
Maximum Peak Voltage¬	600V_p
Maximum Current (per Circuit)	2 A
Maximum Current (per Module)	12 A
Operating Temperature Range	0°…+60°C (32°…140°F) Non-Condensing
Certifications	cURus Recognized (File E113724 Guide NRAQ2) CSA Certified (File LR1234) CE

¬ Transient voltage greater than 600V_p use a UL Recognized suppression device rated at 2.5 kV withstand.

Pinout

Fuse Module Connections
Connector Pin Reference from I/O	PanelConnect Connector Pin Reference	Connector Pin Reference from I/O	PanelConnect Connector pin Reference from I/O