30 mm NEMA
|
|
Description
The Bulletin 800T and 800H 30.5 mm Emergency Stop devices provide increased reliability. E-stops with normally closed late break contacts comply with EN418 and IEC 947‑5‑5 standards. This means the operator will latch when actuated before the contacts will change state.
Application flexibility is offered with 2‑position push-pull or 2‑position push-pull/twist release configurations. Non-illuminated and illuminated operator options are available. Contact block versions are also available that provide IP2X finger-safe protection.
Rockwell Automation also offers Self-Monitoring™ contact blocks (SMCB) which feature enhanced E-stop safety for critical process control applications. The SMCB monitors whether or not it is properly installed on the operator so that the normally closed contacts will open when the E-stop is actuated. If the SMCB is separated from the operator for any reason, the controlled circuit will automatically open.
Features
- 30.5 mm mounting hole
- Type 4/13 watertight/oiltight (Bul. 800T)
- Type 4/4X/13 corrosion-resistant/watertight/oiltight (Bul. 800H)
- Heavy industrial stations and operators
Standards Compliance
UL 508
CCC
Certifications
UL Listed
(File No. E14840, E10314
Guide No. NKCR, NOIV)
CSA Certified
(File No. LR1234, LR11924)
CSA C22.2, No. 14
EN/IEC: 60947-5-1
Specifications
| Electrical Ratings | ||
| Contact ratings | Refer to the contact ratings tables below. | |
| Dielectric strength | 2200V for one minute, 1300V for one minute (Logic Reed) | |
| Electrical design life cycles | 1 000 000 at max. rated load, 200 000 at max. rated load (Logic Reed) | |
| Mechanical Ratings | ||
| Vibration | 10…2000 Hz 1.52 mm displacement (peak-to-peak) max./10 G max. (except Logic Reed) | |
| Shock | 1/2 cycle sine wave for 11 ms ³ 25 G (contact fragility) and no damage at 100 G | |
| Degree of protection | Type 1/4/12/13 (Bul. 800T); Type 1/4/4X/12/13 (Bul. 800H); EN/IEC 60529 IP66/65 | |
| Mechanical design life cycles (Push-pull/twist-to-release) |
250 000 min. | |
| Contact operation | Shallow, mini, and low voltage contact blocks: Slow, double make and break Logic Reed and sealed switch contact blocks: Single break magnetic |
|
| Wire gauge/Terminal screw torque | #18…12 AWG / 6…8 lb•in | |
| Typical operating forces | ||
| 2-position push-pull | 7.5 lbs max. push or pull | |
| Twist-to-release or push-pull | 9 lbs max. push or pull 30 in oz. max. twist, 6 in oz. minimum return | |
| Contact blocks | Standard | 1 lb |
| Logic Reed | 1 lb max. | |
| Sealed switch | 3 lbs max. at 0.205 in plunger travel | |
| Stackable sealed switch | 1 lb max. | |
| Environment | ||
| Temperature range | Operating | –40…+131 °F (–40…+55 °C) |
| Storage | –40…+185 °F (–40…+85 °C) | |
| Note:Operating temperatures below freezing are based on the absence of moisture and liquids. Contact your local Rockwell Automation sales office or Allen-Bradley distributor for use in lower temperature applications. | ||
| Humidity | 50…95% RH from 77…140 °F (25…60 °C) per Procedure IV of MIL-STD-BIOC, Method 507.1 cycling test | |
Standard Contact Ratings
Minimum: 24V 24 mA
Maximum thermal continuous current Ith 10 A AC/2.5 A DC. Bulletin 800T and 800H units with Cat. No. 800T-XA contacts have ratings as follows:
| Max. Opertnl. Volts Ue |
Utilization Category | Rated Operational Currents | |||
| IEC | NEMA | Volts Ue | Make | Break | |
| AC 600 | AC-15 | A600 | 120…600 72…120 24…72 |
7200VA 60 A 60 A |
720VA 720VA 10 A |
| DC 600 | DC-13 | Q600 | 28…600 24…28‡ |
69VA 2.5 A |
|
| ‡ For applications below 24V/24 mA, PenTUFF™ or Logic Reed contacts are recommended. | |||||
Product Selection
2-Position Push-Pull and Push-Pull/Twist Release, Non-Illuminated
Note: A jumbo or large legend plate is recommended, if space allows.
|
|
|
||
| 2-Position Push-Pull Cat. No. 800T-FX6D4 |
2-Position Push-Pull / Twist Cat. No. 800T-FXT6D4 |
2-Position Push-Pull / Twist Cat. No. 800H-FRXT6D4 |
| Contact Type | Operator Position | Button Color | Type 4/13 | Type 4/4X/13 | |||
|
|
Push-Pull | Push-Pull/Twist Release |
Push-Pull/Twist Release |
|||
| Out | In | Cat. No. | Cat. No. | Cat. No. | |||
|
N.C.L.B.⋆ | X | O | Red | 800T-FX6D4 | 800T-FXT6D4 | 800H-FRXT6D4 |
|
N.O. - N.C.L.B.⋆ | O X |
X O |
Red | 800T-FX6A1 | 800T-FXT6A1 | 800H-FRXT6A1 |
|
N.C.L.B. - N.C.L.B.⋆ | X X |
O O |
Red | 800T-FX6A5 | 800T-FXT6A5 | 800H-FRXT6A5 |
|
S.M.C.B.⋆ ‡ | X | O | Red | 800TC-FX6D4S | 800TC-FXT6D4S | 800HC-FRXT6D4S |
|
N.O. - S.M.C.B.⋆ ‡ | O X |
X O |
Red | 800TC-FX6A1S | 800TC-FXT6A1S | 800HC-FRXT6A1S |
|
S.M.C.B. - S.M.C.B⋆ ‡ | X X |
O O |
Red | 800TC-FX6A5S | 800TC-FXT6A5S | 800HC-FRXT6A5S |
| Note:X = Closed/O = Open | |||||||
| Note:Emergency stop push buttons are compliant with EN 418 and EN/IEC 60947-5-5 Standards when using N.C.L.B. contact blocks. | |||||||
| Note:These caps are only available in plastic. | |||||||
| ⋆ Normally closed late break contact. When button is pushed from the OUT to IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs. | |||||||
| ‡ The Self Monitoring Contact Block (S.M.C.B.) is composed of a N.C.L.B. contact wired in series with a N.O. monitoring contact. The N.O. monitoring contact automatically closes when the S.M.C.B. is properly installed onto the E-stop operator. If the S.M.C.B. is separated from the E-stop operator, the N.O. monitoring contact will automatically open. | |||||||
2-Position Push-Pull and Push-Pull/Twist Release Units, Illuminated
Note: A jumbo or large legend plate is recommended, if space allows.
|
|
|
||
| Illuminated 2-Position Push-Pull Cat. No. 800T-FXP16RA1 |
Illuminated 2-Position Push-Pull/Twist Cat. No. 800T-FXTP16RA1 |
Illuminated 2-Position Push-Pull/Twist Cat. No. 800H-FRXTP16RA1 |
| Type | Lamp Type | Volts | Color | Contacts | Operator Position | Type 4/13 | Type 4/4X/13 | ||
|
|
|
Push-Pull Release |
Push-Pull/Twist Release |
Push-Pull/Twist Release |
|||||
| Maintained | Maintained | ||||||||
| Out | In | Cat. No. | Cat. No. | Cat. No. | |||||
| Full Voltage | Incandescent | 24V AC/DC | Red | N.O. - N.C.L.B. ⋆ § |
O X |
X O |
800T-FXQ24RA1 | 800T-FXTQ24RA1 | 800H-FRXTQ24RA1 |
| LED | 120V AC | 800T-FXQH10RA1 | 800T-FXTQH10RA1 | 800H-FRXTQH10RA1 | |||||
| 24V AC/DC | 800T-FXQH24RA1 | 800T-FXTQH24RA1 | 800H-FRXTQH24RA1 | ||||||
| Transformer | Incandescent | 120V AC | Red | N.O. - N.C.L.B. ⋆ § |
O X |
X O |
800T-FXP16RA1 | 800T-FXTP16RA1 | 800H-FRXTP16RA1 |
| 240V AC | 800T-FXP26RA1 | 800T-FXTP26RA1 | 800H-FRXTP26RA1 | ||||||
| LED | 120V AC | 800T-FXPH16RA1 | 800T-FXTPH16RA1 | 800H-FRXTPH16RA1 | |||||
| 240V AC | 800T-FXPH26RA1 | 800T-FXTPH26RA1 | 800H-FRXTPH26RA1 | ||||||
| Note:X = Closed/O = Open | |||||||||
| Note:Emergency stop push buttons are compliant with EN 418 and EN/IEC 60947-5-5 Standards when using N.C.L.B. contact blocks. | |||||||||
| ⋆ Normally closed late break contact. When button is pushed from the OUT to IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs. | |||||||||
| ‡ The Self Monitoring Contact Block (S.M.C.B.) is composed of a N.C.L.B. contact wired in series with a N.O. monitoring contact. The N.O. monitoring contact automatically closes when the S.M.C.B. is properly installed onto the E-stop operator. If the S.M.C.B. is separated from the E-stop operator, the N.O. monitoring contact will automatically open. | |||||||||
| § Contact your local Rockwell Automation sales office or Allen-Bradley distributor for availability of illuminated E-stops with Self Monitoring Contact Blocks (S.M.C.B.s). | |||||||||
Accessories
| Type | Style | Color | Cat. No. | |
|
Emergency Stop Legend Plates | For 800T Buttons | Yellow, Blank | 800T-X646 |
| Yellow, Emergency Stop | 800T-X646EM | |||
|
For 800H Buttons | Yellow, Emergency Stop | 800H-W690 | |