Catalogs > Drives Catalog > PowerFlex 700S
PowerFlex 700S
| Introduction |  |
Conformity to Standards | |
Drive Description | |
Catalog Number Explanation | |
| Hardware Control Options | |
Factory Installed Options | |
User Installed Options | |
Drive Application Software | |
| Human Interface and Wireless Interface Modules IP20/NEMA Type 1 (Position e) |
||||
|
|
|
||
| Cat. Code: 0 No HIM (Blank Plate) |
Cat. Code: 3 LCD Display, Full Numeric Keypad |
Cat. Code: 5 LCD Display, Programmer Only |
||
|
||||
| Cat. Code: C Door Mounted Bezel LCD Display, Full Numeric Keypad Frame 10 & Up |
||||
| Documentation | |
| Description | Cat. Code |
| (Position f) | |
| Quick Start Guide | E |
| No Documentation | N |
| Internal Brake IGBT | |||
| Drive Input Voltage | Brake IGBT | Frame | Cat. Code |
| (Position g) | |||
| 208…480V AC | Standard | 1…3 | Y |
| Optional | 4 | Y | |
| 5 | Y | ||
| 4…6 | N | ||
| 6 | Y | ||
| 9 | Y | ||
Internal Dynamic Brake Resistors
These resistors have a limited duty cycle. Refer to the PowerFlex Dynamic Braking Selection Guide to determine if an internal resistor will be sufficient for your application. An external resistor may be required.
| Drive Input Voltage | Frame | Brake Resistance | Cat. Code |
| W | (Position h) | ||
| 208…240V AC | 1 (1.0-5.0 Hp) | 62 | Y |
| 1 (7.5 Hp) | 22 | Y | |
| 2 | 22 | Y | |
| 380…600V AC | 1 | 115 | Y |
| 2 | 68 | Y | |
| All | – | N | |
| Internal EMC Filter | |||
| Drive Input Voltage | Frame | CE Filter | Cat. Code |
| (Position i) | |||
| 208…240V AC 380…480V AC 600…690V AC |
1…6 | with CE Filter & Choke, No dv/dt Filter | A |
| 380…500V AC | 9…14 | with CE Filter, No Choke, No dv/dt Filter | B |
| 600…690V AC | 14 | with CE Filter & dv/dt Filter, No Choke | E |
| 380…500V AC | 9 | No CE Filter, No Choke, No dv/dt Filter ¬ | N |
| ¬ For use on a high resistive ground or ungrounded distribution system. | |||
| Internal Communication Adapters | |
| Description | Cat. Code |
| (Position j) | |
| None | N |
| ControlNet™ Communication Adapter (Coax) | C |
| DeviceNet™ Communication Adapter | D |
| EtherNet/IP™ Communication Adapter | E |
| Remote I/O Communication Adapter | R |
| RS485 DF1 Communication Adapter | S |
| DriveLogix Comm Option, ControlNet (Coax) ‡ § | 1 |
| DriveLogix Comm Option, ControlNet Redundant (Coax) ‡ § | 2 |
| DriveLogix Comm Option, ControlNet (Fiber) ‡ § | 3 |
| DriveLogix Comm Option, ControlNet Redundant (Fiber) ‡ § | 4 |
| DriveLogix Comm Option, DeviceNet (Open Conn.) ‡ § | 5 |
| DriveLogix Comm Option, EtherNet/IP (Twisted Pair) ‡ § | 6 |
| ‡ Must have the DriveLogix option. | |
| § Requires Expanded Cassette. | |
| Control Options | ||
| Control Option | Description | Cat. Code |
| (Position k) | ||
| Phase II Control | Expanded Cassette Only | A |
| Expanded Cassette w/SynchLink | B | |
| Expanded Cassette w/Logix Expansion Board | C | |
| Expanded Cassette w/Logix Expansion Board & SynchLink | D | |
| Slim Cassette | G | |
| Slim Cassette w/SynchLink | H | |
| Feedback Options | |
| Description | Cat. Code |
| (Position l) | |
| No Option (includes Standard Encoder Interface) | N |
| Resolver, 10…26V, 10 kHz, 10…16 bit | A |
| Stegmann - High Resolution Encoder Hyperface, 8.5V DC, 20 bit, 100k/r § | B |
| Multi-Device Interface - for Stegmann or Linear Temposonics § | C |
| 2nd Encoder, 5V or 12V Configurable by the Drive § | E |
| DriveGuard Safe-Off (w/2nd Encoder) § | S |
| Stegmann & 2nd Encoder § | T |
| Stegmann & DriveGuard Safe-Off (w/2nd Encoder) § | U |
| § Requires Expanded Cassette. | |
| Additional Configurations | |
| Description | Cat. Code |
| (Position m) | |
| Phase II Control | E |
| Phase II Control, with DriveLogix5730 Controller | K |
| Phase II Control, with DriveLogix5730 Controller & EtherNet/IP | L |