|
Drives Service & Support > 1395 > Specifications
| Electrical | |
| Input Voltages | 150 460VAC +/ 10%, 3 phase |
| Input Power | 1.5 kVA to 660 kVA |
| Input Frequency | 50/60Hz +/ 3 Hz. |
| Max Rate of Change | 0.5 Hz/Sec. |
| Output Voltage | 240VDC (230VAC Input) 400VDC (380 415 AC Input) 500VDC (460VAC Input) |
| Output Horsepower (Continuous) | 1 to 300 HP, 240VDC 1.5 to 500 HP, 400VDC 2 to 600 HP, 500VDC |
| Output Current | 3.6 to 980A |
| Field Voltage | 120 150VDC, 230VAC 200 250VDC, 380VAC 220 270VDC, 415VAC 240 300VDC, 460VAC Field Voltage Source is selectable between internal or external supply. |
| Field Current | 1 30HP, 230V; 2 60HP, 460V Drive: 150mA 10 Amperes Continuous 40 100HP, 230V; 75 200HP, 460V Drive: 650mA 20 Amperes (continuous) 125 300HP, 230V; 250 600HP, 460V Drive: 650mA 40 Amperes (continuous) |
| Field Control | A 6:1 speed range with an encoder or DC tach feedback |
| Field Economy | Programmable enable, time delay, power on standby |
| Armature Firing | Phase sequence insensitive, Regenerative/Nonregenerative |
| Output Waveform | 6 pulse, full wave, NEMA Code C |
| Controller Current Output | 150% for one minute, 200% for 10 seconds, 260% for 5 seconds |
| Armature Control | Tapered current limit,di/dt limit, Instantaneous overcurrent, Programmable motor overload |
| Speed Regulation | |
| Encoder | 0.01% of set speed (over a 10:1 speed range); 0.001% of top speed (over a 100:1 speed range). |
| DC Tachometer | 0.5% of top speed with 5PY tachometer; 0.1% of top speed with BC42 tachometer. |
| Armature Voltage | 2% of top speed |
| Feedback Devices | |
| DC Tachometer | 5 PY, BC42 or equal |
| Encoder | Incremental, dual channel; 12 volts, 500mA, isolated with differential transmitter, 102.5 kHz max. Quadrature : 90°± 27° @ 25°C, Duty Cycle: 50% ± 10% Source/Sink capable, A-B 845H or equal |
| External Inputs | |
| Enable/Contingency Coast Stop | 24VDC/115VAC, hard-wired to DC contactor |
| System Reset | 24VDC/115VAC, Isolated |
| Motor Thermostat | 24VDC/115VAC, Isolated |
| Communication Port | RS-422 for programming terminal |
| External Outputs | |
| Drive Ready/Faulted | N.O. relay contact, open when drive faulted or de-energized, closed when ready. Contact rating - 1 ADC @ 24 VDC or 0.5A @ 120VAC |
| Environmental | |
| Ambient Operating Temperature | 0° to 55°C (32° - 130° F) |
| Relative Humidity | 5% to 95%, non-condensing |
| Altitude | 3,300 feet (1,000 meters) |
| Standard Features | |
| Accel/Decel | 0.1 to 6554 seconds, independently programmable. |
| Preset Speeds | 5 adjustments, programmable |
| Jog Speeds | 2 adjustments, programmable |
| "S" Ramp | Programmable |
| Motor Operated Pot (MOP) | 10 adjustments, programmable |
| Options | |
| Discrete Adapter Board | |
| Digital Inputs (4) | 24VDC or 120VAC, 10 mA. NOTE: A separate board and part number is used for each voltage rating. |
| Digital Outputs (2) | Dry relay contacts rated at 0.6 amps at 125VAC or 2.0 amps at 30VDC. |
| Analog Inputs (4) | 0 to +/- 10 VDC, differential input impedance - 20K ohms. |
| Analog Outputs (4) | -10 to + 10VDC, 1mA minimum output impedance - 200 ohms. |
| Power Supply (For external use) | +10VDC, 4mA maximum, -10VDC, 4mA maximum. |
| Digital Reference Board | |
| Digital Reference Input (1) | Current source and sink input for high common mode noise immunity. Nominal 5VDC or 12VDC interface (internal hardware configurable), + 10mA nominal current source/sink requirements. |
| Digital Inputs (10) | 24VDC Nominal; 18VDC minimum, 28VDC maximum; 10 ma nominal. |
| Discrete Outputs (5) | 24VDC nominal; Current sourcing type driver; Diode clamped for inductive load; 18VDC minimum, 28VDC maximum; 1.5VDC saturation, 100mA maximum load. |
| Analog Inputs (2) | 0 to +/- 10 VDC, differential input impedance - differential > 1m ohm; 20K ohms (single ended to analog common). |
| Analog Outputs (2) | -10 to +10VDC, 2.5mA maximum output impedance - 200 ohms. |
| Power Supply (for external use) | +10VDC, 4mA maximum, -10VDC, 4mA maximum. |
| Node Adapter board | This board allows the Bulletin 1395 to be controlled using an Allen-Bradley PLC controller from either the PLC3 or PLC5 family. The +5V Node Adapter board power is generated internally in the Drive. |
| Multi-Communications Adapter Board | |
| Power Supply | Board power provided by Drive discrete input, 24VDC or 115VAC, jumper selectable. |
| Communications Channels (2) | Each channel can be configured as either Allen-Bradley Remote I/O (RIO) or Allen-Bradley Data Highway + (DH+) interfaces. Compatible with PLC3, PLC250,PLC5/15, PLC5/25, PLC5/40, PLC5/60 and Controlview. |
| Function Blocks (4) | These programmable function blocks can be used to manipulate data. |
| Discrete Input (1) | One programmable discrete input is available (24VDC or 115VAC). |