|
Number |
Status Indicator |
Description |
1 |
DSI Connection Status |
|
2 |
Adapter Status |
|
3 |
DeviceNet Status |
|
4 |
Not Used for DeviceNet |
| Status | Cause | Corrective Action |
| Off | The adapter is not powered or is not connected properly to the drive. | • Securely connect the adapter to the drive using the ribbon cable. • Apply power to the drive. |
| Flashing Red |
The adapter is not receiving communication from the drive, connected drive is faulted, or a drive is missing in Multi-Drive mode. | • Clear any drive faults. • Verify that cables are securely connected. • Cycle power to the drive. |
| Solid Red |
The drive has refused an I/O connection from the adapter. Another DSI peripheral is using the same DSI port as the adapter. |
Important: Cycle power to the product after making the following correction: Verify that all DSI cables are securely connected and not damaged. Replace cables if necessary. |
| Flashing Green |
The adapter is establishing an I/O connection to the drive or [DSI I/O Config] is configured for all I/O disabled. | • No Action. This status indicator will turn solid green or red. • Verify Parameter 15, [DSI I/O Config] settings. • Normal behavior if no DSI I/O is enabled. |
| Solid Green |
The adapter is properly connected and is communicating with the drive. |
No Action. |
| Orange | Daisy-chained drives in Multi-Drive mode are not all Allen-Bradley drives (PowerFlex 4/40). |
Use Allen-Bradley PowerFlex 4/40’s for the daisy-chained drives. |
| Status | Cause | Corrective Action |
| Off | The adapter is not powered. | • Securely connect the adapter to the drive using the ribbon cable. • Apply power to the drive. |
| Flashing Red |
The adapter has failed the firmware test, connected drive is faulted, or a drive is missing in Multi-Drive mode. | • Clear faults in the drive. • Cycle power to the drive. • If cycling power does not correct the problem, the parameter settings may have been corrupted. Reset defaults and reconfigure the module. • If resetting defaults does not correct the problem, flash the adapter with the latest firmware release. • For Multi-Drive mode, determine which drive is missing or faulted. Check cabling and configuration settings (see Configuring the RS-485 Network section in Chapter 7 of the user manual). |
| Solid Red |
The adapter has failed the hardware test. | • Cycle power to the drive. • Replace the adapter. |
| Flashing Green |
The adapter is operational, but is not transferring I/O data. | • Place the scanner in RUN mode. • Program the controller to recognize and transmit I/O to the adapter. • Configure the adapter for the program in the controller. • Normal behavior if no DSI I/O is enabled. |
| Solid Green |
The adapter is operational and transferring I/O data. | No Action. |
| Status | Cause | Corrective Action |
| Off | The adapter and/or network is not powered or adapter is not connected properly to the network. | • Securely connect the adapter to the drive using the Internal Interface cable and to the network using a DeviceNet cable. • Correctly connect the DeviceNet cable to the DeviceNet plug. • Apply power to the drive and network. |
| Flashing Red |
A DeviceNet I/O connection has timed out. | • Place the scanner in RUN mode, or apply power to the peer device that will send I/O. • Check the amount of traffic on the network. |
| Solid Red |
Failed duplicate node detection test or bus off condition exists. | • Configure the adapter to use a unique node address on the DeviceNet network. • Configure the adapter to use the correct network data rate. • Ensure network has correct media installed. |
| Flashing Green |
The adapter is properly connected but is not communicating with any devices on the network. | • Place the controller in RUN mode, or apply power to the peer device that will send I/O. • Program a controller or peer device to recognize and transmit I/O to the adapter. • Configure the adapter for the program in the controller or the I/O from the peer device. |
| Solid Green |
The adapter is properly connected and communicating on the network. | No action required. |
Not Used in this configuration.