|
Click for Dimensions
| Category | Specifications |
|
| Environment | Altitude | 1000 m (3300 ft) max. without derating |
| Ambient Operating Temperature | IP20: –10 to 50 degrees C (14 to 122 degrees F) NEMA 1: –10 to 40 degrees C (14 to 104 degrees F) |
|
| Cooling Method | Convection: 0.2 kW (0.25 HP) drive ratings, Catalog Numbers 22A-V1P5N104, 22A-A1P5N114, 22A-A1P5104 and 22A-B1P5N104 Fan: All other drive ratings. |
|
| Storage Temperature: | –40 to 85 degrees C (–40 to 185 degrees F) | |
| Atmosphere: | Important: Drive must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust. If the drive is not going to be installed for a period of time, it must be stored in an area where it will not be exposed to a corrosive atmosphere. | |
| Relative Humidity: | 0 to 95% non-condensing | |
| Shock (operating): | 15G peak for 11ms duration (±1.0ms) | |
| Vibration (operating): | 1G peak, 5 to 2000 Hz | |
| Control | Carrier Frequency | 2-16 kHz. Drive rating based on 4 kHz. |
| Frequency Accuracy | Digital Input: Within ±0.05% of set output frequency. Analog Input: Within 0.5% of maximum output frequency. |
|
| Speed Regulation - Open Loop with Slip Compensation: |
±2% of base speed across a 40:1 speed range. | |
| Stop Modes: | Multiple programmable stop modes including - Ramp, Coast, DC-Brake, Ramp-to-Hold and S Curve. | |
| Accel/Decel: | Two independently programmable accel and decel times. Each time may be programmed from 0 - 600 seconds in 0.1 second increments. | |
| Intermittent Overload: | 150% Overload capability for up to 1 minute 200% Overload capability for up to 3 seconds |
|
| Electronic Motor Overload Protection |
Class 10 protection with speed sensitive response. |
|
| Input / Output Ratings | Output Frequency | 0-400hz (Programmable) |
| Efficiency | 97.5% (Typical) | |
| Approvals |  |
|
| Digital Control Inputs | SRC (Source) Mode | 18-24V = ON 0-6V = OFF |
| SNK (Sink) Mode | 0-6V = ON 18-24V = OFF |
|
| Analog Control Inputs | 4-20mA Analog | 250 Ohm Input Impedance |
| 0-10V DC Analog | 100k Ohm Input Impedance | |
| External Pot | 1-10k ohms, 2 Watt Minimum | |
| Control Output Programmable Output (form C relay) |
Resistive Rating | 3.0A at 30Vdc/125Vac/240Vac |
| Inductive Rating | 0.5A at 30Vdc/125Vac/240Vac | |
| Opto Outputs | 30V DC, 50mA Non-inductive | |
| Analog Outputs (10 bit) | 0-10V, 1k ohm Min. : 4-20mA, 525 ohm Max. | |
| Protective Features | Motor Protection | I2T Overload Protection - 150% for 60 Seconds, 200% for 3 Seconds (Provides Class 10 Protection) |
| Over Current | 200% Hardware Limit 300% Instantaneous Fault |
|
| Over Voltage | 100-120Vac Input - Trip at 405Vdc Bus Voltage (Equivalent to 150Vac Incoming Line) | |
| 200-240Vac Input - Trip at 405Vdc Bus Voltage (Equivalent to 290Vac Incoming Line) | ||
| 380-480Vac Input - Trip at 810Vdc Bus Voltage (Equivalent to 575Vac Incoming Line) | ||
| Under Voltage | 100-120Vac Input - Trip at 210Vdc Bus Voltage (Equivalent to 75Vac Incoming Line) | |
| 200-240Vac Input - Trip at 210Vdc Bus Voltage (Equivalent to 150Vac Incoming Line) | ||
| 380-480Vac Input - Trip at 390Vdc Bus Voltage (Equivalent to 275Vac Incoming Line) | ||
| Control Ride Through | Minimum Ride Through is 0.5 Seconds, Typical Value 2 Seconds | |
| Faultless Power Ride Through | 100 milliseconds | |
| Dynamic Braking | Internal brake IGBT included with all ratings 0.75kW (1 HP) and larger. | |