Allen-Bradley Home
Drives Service & Support

General Resources
 

Drives Service & Support > Powerflex 700S > Data Sheets Frame 9+

Category Specification 380/400V
Drive		 480V
Drive		 500V
Drive		 600V
Drive		 690V
Drive
Protection AC Input Overvoltage Trip: 475VAC 570VAC 611VAC 690VAC -
Bus Overvoltage Trip: 675VDC 810VDC 810VDC 1013VDC -
Bus Undervoltage Trip: Adjustable
Nominal Bus Voltage: 540VDC 648VDC 645VDC 810VDC -
Heat Sink Thermistor: Monitored by microprocessor overtemp trip

Drive Overcurrent Trip
Software Current Limit: Calculated value, 105% of motor rated to 200% of drive rated.
105% of 3 sec. rating (158%-210%)
143% of 3 sec. rating (215%-287%)
Hardware Current Limit: 105% of 3 sec. rating (158%-210%)
Line Transients: Up to 6000 volts peak per IEEE C62.41-1991
Control Logic Noise Immunity: Showering arc transients up to 1500V peak
Power Ride-Thru: 15 milliseconds at full load
Logic Control Ride-Thru 0.25 sec., drive not running
Ground Fault Trip: Ground Fault Trip:
Short Circuit Trip: Phase-to-phase on drive output
Agency
Certification

The drive is also designed to meet the following specifications:

  • NFPA 70 - US National Electrical Code
  • NEMA ICS 3.1 - Safety standards for Construction and Guide for Selection, Installation and Operation of Adjustable Speed Drive Systems.
  • IEC 146 - International Electrical Code.
Listed to UL508C and CAN/CSA-C2.2 No. 14-M91.
Marked for all applicable European Directives
EMC Directive (89/336/EEC)
Emissions
EN 61800-3 Adjustable Speed electrical power drive systems
Part 3
Low Voltage Directive (73/23/EEC)
EN 50178 Electronic Equipment for use in Power Installations
Category Specification
Environment Altitude: 1000 m (3300 ft.) max. without derating
Surrounding Air Temperature without
Derating:		 Based on drive rating, refer to Drive Frame ahapters
Storage Temperature (all const.): -40 to 70° C (-40 to 158° F)
Relative Humidity: 5 to 95% non-condensing
Shock: 15G peak for 11 ms duration (+/- 1.0 ms)
Vibration: 2 mm (0.0787 in.) displacement, 1G peak
EN50178 / EN60068-2-6
Atmosphere: Important: Drive must not be installed in an area where the
ambient atmosphere contains volatile or corrosive gas, vapors
or dust. If the drive is not going to be installed for a period of
time, it must be stored in an area where it will not be exposed to
a corrosive atmosphere.
Electrical Voltage Tolerance: - 10% of minimum, + 10% of maximum.
Frequency Tolerance: 47-63 Hz
Input Phases: Three-phase input provides full rating for all drives. Single-phase operation provides 50% of rated current.
Displacement Power Factor: 0.98 across speed range
Efficiency: 97.5% at rated amps, nominal line volts.
Max. Short Circuit Current Rating:
Using Recommended Fuse or Circuit
Breaker Type		 Maximum short circuit current rating to match specified fuse/circuit breaker capability.
</= 200,000 Amps
Maximum Drive to Motor Power Ratio The drive to motor rating cannot exceed a 2:1 ratio
Control Method
Induction Motor:
Brushless Motor:		 Sine coded PWM with programmable carrier frequency, Indirect
Self-Organized, Field-Oriented Control, Current-regulated. Ratings apply to all drives (refer to the De-rating Guidelines in the
PowerFlex Reference Manual). The drive can be supplied as 6
pulse or 12 pulse in a configured package.
Carrier Frequency
Frames 0 - 4		 Drive rating: 2 kHz, Settings: 2, 4, 8, 10 kHz
Output Voltage Range: 0 to rated motor voltage
Output Frequency Range: 0 – 320 Hz
Speed Regulation:
Without Feedback 0.1% of base speed across 120:1 speed range
120:1 operating range
50 rad/sec bandwidth
With Feedback 0.001% of base speed across 120:1 speed range
1000:1 operating range
300 rad/sec bandwidth
Torque Regulation:
Without Feedback +/-10%, 600 rad/sec bandwidth
With Feedback +/-5%, 2500 rad/sec bandwidth
Selectable Motor Control: Field Oriented Control with and without a feedback device and Brushless motor control
Stop Modes: Multiple programmable stop modes including – Ramp, Coast and Current Limit
Accel/Decel Adjustable from 0.5 to 4.0 seconds
S-Curve Time 110% Overload capability for up to 1 minute
150% Overload capability for up to 3 seconds
Current Limit Capability: Independent Motoring and Regenerative Power Limits programmable to 800% of rated output current
Electronic Motor Overload Protection Class 10 protection with speed sensitive response. Investigated by U.L. to comply with N.E.C. Article 430 U.L.
File E59272, volume 12.
Feedback Encoder Inputs Dual Channel Plus Marker, Isolated with differential transmitter Output (Line Drive) Incremental, Dual Channel Quadrature type
Encoder Voltage Supply 5V DC or 12 V DC (5V DC requires an external power supply)
Maximum Encoder Input Frequency 400khz
Stegmann Option
Encoder Voltage Supply 11.5V DC @ 130 mA
Hi-Resolution Feedback Sine/Cosine 1V P-P Offset 2.5
Maximum Cable Length 182 m (600 ft.)
RS-485 Interface Hi-Resolution Feedback Option card obtains the following information via the Hiperface RS-485 interface shortly after powerup:
Address, Command Number, Mode, Number of turns, Number of Sine/Cos cycles, Checksum
Customer I/O Plus (P1) - HiRes Allen-Bradley PN: S94262912
Weidmuller PN: BL3.50/90/12BK
Resolver Option:
Excitation Freq 2400 Hz
Excitation Voltage 4.25 - 26 Vrms
Operating Frequency Range 1 - 10 kHz
Resolver Feedback Voltage 2V ± 300 mV
Maximum Cable Length 304.8 meters (1000 ft.)
Category Specification
DriveLogix User Available Memory  
Base: 256 kbytes
With Memory Expansion Board: 768kbytes
Battery: 1756-BA1 (Allen-Bradley PN 94194801) 0.59g lithium
Serial Cable: 1761-CBLPM02 to 1761-NET-AIC
1761-CBLPA00 to 1761-NET-AIC
1756-CP3 directly to controller
1747-CP3 directly to controller
category 3 (2)
Flex I/O Connection: Up to (8) modules
FLEXBUS Current Output: 640 mA maximum @ 5.1V dc
Cable: 4100-CCF3