Allen-Bradley Home
Drives Service & Support

General Resources
 

Drives Service & Support > PowerFlex 700S Phase II control > Data Sheets

Category
Specification
Protection   200 - 208V 240V 380 - 400V 480V 600V
AC Input Overvoltage Trip 247 VAC 285VAC 475VAC 570VAC 690VAC
Bus Overvoltage Trip 350VDC 405VDC 675VDC 810VDC 1013VDC
Bus Undervoltage Trip Adjustable
Nominal Bus Voltage 281VDC 324VDC 540VDC 648VDC 810VDC
Heat Sink Thermistor Monitored by microprocessor overtemp trip

 

Category Specification
Protection Drive Overcurrent Trip
  • Software Current Limit: Calculated Value, 105% of motor rated to 200% of drive rated
  • Hardware Current Limit: 105% of 3 sec. rating (158%-210%)
  • Instantaneous Current Limit: 143% of 3 sec. rating (215%-287%)
Line Transients Up to 6000 votls peak per IEEE C62.41-1991
Control Logic Noise Immunity Showering arc transients up to 1500V peak
Power Ride-Thru 15 milliseconds at full load
Logic Control Ride-Thru 0.25 sec., drive not running
Ground Fault Trip Phase-to-ground on drive output
Short Circuit Trip Phase-to-phase on drive output
Agency Certification The drive is designed to meet the following specifications:
NFPA 70 – US National Electric Code
NEMA ICS 3.1 – Safety Standards for Construction and Guide for Selection,
Installation and Operation of Adjustable Speed Drive Systems.
NEMA 250 – Enclosures for Electrical Equipment
IEC 146 – International Electrical Code.
C-UL-US UL and cUL Listed to UL508C and CAN/CSA-C2.2 No. 14-M91
CE Marked for all applicable European Directives
EMC Directive (89/336/EEC)
Emissions
EN 61800-3 Adjustable Speed electrical power drive systems Part 3
Immunity
EN 61800-3 Second Environment, Restricted Distribution
Low Voltage Directive (73/23/EEC)
EN 50178 Electronic Equipment for use in Power Installations
Environment Altitude 1000 m (3300 ft.) max. without derating
Surrounding Air Temperature without
Derating:
  • Open Type: 0 to 50° C (32 to 122° F)
  • IP20: 0 to 50° C (32 to 122° F)
  • NEMA Type 1: 0 to 40° C (32 to 104 ° F)
  • IP56, NEMA Type 4X: 0 to 40 ° C (32 to 104 ° F)

Note: Frames 9 & 10 are rated 0 to 40 ° C (32 to 104 ° F) surrounding air.
Storage Temperature (all const.): -40 to 70° C (-40 to 158° F)
Relative Humidity: 5 to 95% non-condensing
Shock: 10G peak for 11 ms duration (+/- 1.0 ms)
Vibration: 0.152 mm (0.006 in.) displacement, 1G peak, 5.5 Hz
Atmosphere Important: Frame 9 & up drives must not be installed in an area where the ambient
atmosphere contains volatile or corrosive gas, vapors or dust. If the drive is not going to be installed for a period of time, it must be stored in an area where it will not be exposed to a corrosive atmosphere.

 

Category Specification
Electrical AC Input Voltage Tolerance: See for Full Power and Operating Range
Frequency Tolerance: 47-63 Hz
Input Phases: Three-phase input provides full rating for all drives. Single-phase operation provides 50% of
rated current.
DC Input Voltage Tolerance: +/- 10% of Nominal Bus Voltage (above)
Displacement Power Factor: 0.98 across speed range
Efficiency: 97.5% at rated amps, nominal line volts.
Max. Short Circuit Current Rating: Maximum short circuit current rating to match specified fuse/circuit breaker capability.
≤ 200,000 Amps
Maximum Drive to Motor Power Ratio The drive to motor rating cannot exceed a 2:1 ratio
Control Method
  • Induction Motor: Ratings apply to all drives (refer to the Derating Guidelines). The drive can be supplied as 6 pulse or 12 pulse in a configured package. Indirect Self-Organized, Field-Oriented Control
  • Brushless Motor: Current-regulated, sine-coded PWM with programmable carrier frequency
Carrier Frequency Frames 0 - 4: Drive rating: 4 kHz, Settings: 2, 4, 8, 10 kHz
Frames 9 & up: 2 kHz
Output Voltage Range: 0 to rated motor voltage
Output Frequency Range: 0 – 320 Hz
Speed Control w/ feedback
  • 0.001% of base speed across 120:1 speed range
  • 1000:1 operating range
  • 300 rad/sec bandwidth
Speed Control w/o feedback
  • 0.1% of base speed across 120:1 speed
    range
  • 120:1 operating range
  • 50 rad/sec bandwidth
Torque Regulation w/ feedack +/-5%, 2500 rad/sec bandwidth
Torque Regulation w/o feedback +/-10%, 600 rad/sec bandwidth
Selectable Motor Control: Field Oriented Control with and without a feedback device and permanent magnet motor control
Stop Modes: Multiple programmable stop modes including – Ramp, Coast and Current Limit
Accel/Decel Independently programmable accel and decel times adjustable from 0 to 6553.5 in 0.1 second
increments.
S-Curve Time Adjustable from 0.5 to 4.0 seconds
Intermittent Overload: 110% Overload capability for up to 1 minute
150% Overload capability for up to 3 seconds
Current Limit Capability: Independent Motoring and Regenerative Power Limits programmable to 800% of rated output
current
Electronic Motor Overload Protection Class 10 protection with speed sensitive response. Investigated by U.L. to comply with N.E.C.
Article 430 U.L. File E59272, volume 12.

 

Category Specification
Feedback Encoder Inputs (2): Dual Channel Plus Marker, Isolated with differential transmitter Output (Line Drive) Incremental,
Dual Channel Quadrature type
Encoder Voltage Supply: 5V DC or 12 V DC (5V DC requires an external power supply) 320 mA/channel
Maximum Input Frequency: 400 kHz
Stegmann Hi-Resolution Option:
  • Encoder Voltage Supply: 11.5V DC @ 130 mA
  • Hi-Resolution Feedback: Sine/Cosine 1V P-P Offset 2.5
  • Maximum Cable Length: 182 m (600 ft.)
  • RS-485 Interface: Hi-Resolution Feedback Option card obtains the following information via the Hiperface RS-485 interface shortly after power-up: Address, Command Number, Mode, Number of turns, Number of Sine/Cos cycles, Checksum
  • Customer-I/O Plug (P1) - Hi Res: Allen-Bradley PN: S94262912 -or- Weidmuller PN: BL3.50/90/12BK
Resolver Option:
  • Excitation Frequency: 2400 Hz
  • Excitation Voltage: 4.25-26 Vrms
  • Operating Frequency Range: 1 - 10 kHz
  • Resolver Feedback Voltage: 2V ± 300 mV
  • Maximum Cable Length: 304.8 meters (1000 ft.)
DriveLogix User Available Memory Base: 1.5 megabytes
Battery: 1769-BA
Serial Cable: 1761-CBLPM02 to 1761-NET-AIC
1761-CBLPA00 to 1761-NET-AIC
1756-CP3 directly to controller
1747-CP3 directly to controller
category 3 (2)
Compact I/O Connection: Up to (30) modules
Cable: 20D-DL2-CL3
20D-DL2-CR3